Question about 2002 Mercury Cougar
Fog light relay location
Light relays are located in the engine comparment fuse box, the cover will have a list to show what is what
Posted on May 10, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Look under the dash near where the headlamp switch mounts and if yours is equipped you should see I think it is a blue 4 pin connector with the following wire colors OG,OG/WH,OG/GN,BK.
This is for the fog lamp relay.If yours has this connector then you will need to purchase a relay ford part number F6RZ-14N089-AA should list for about $10.
Posted on Feb 25, 2009
It is located on top of the engine under the throttle body, it sucks, plan on a whole day if you are a good machanic.
Posted on Dec 31, 2008
balkjr Check the 7.5 amp fuse thats under the dash labeled high beams and low beams. I like a idiot checked all the other fuses under the hood but neglected to check that one and it was blown. Once i replaced the fuse my headlights work fine but still no instrument lights. For whatever reason i was able to blow the fuse again by shorting out the dimmer switch so i checked it with a multimeter and it had voltage going in but none out. I unplugged the dimmer switch and looked into it and alias noticed a solder in the middle pin that had snapped off. Its proved trickier than i had expected to solder it back but i know for sure that it is the culprit because i was able to use a pin to reach in it and hold the solder point down to get connection and my instrument lights worked fine. You can look right into the switch and see the solder point thats broke if that seems to be the problem for you also it comes from the middle pin on the switch and solders straight to the board. Just look inside the switch is made fairly open.
Posted on Feb 08, 2009
The power distribution box is
located in the engine compartment.
The power distribution box contains
high-current fuses that protect your
vehicle’s main electrical systems
The starter relay is in position #56 of that box.
Posted on Mar 23, 2009
I just got done replacing the O2 sensors in my 99 Cougar due to throwing a P0135 malfunction code. There's 3. Facing the engine there's one in the front coming off of the front header, which is easy to get to. Another more tricky one if between the engine and the fire wall on the rear header pipe. The third is under the vehicle behind the transmission pan on top of the exhaust. In order to replace the O2 sensor near the fire wall you will need to remove the 4 retaining bolts for the ECM module and move it out of the way. Additionally you will need to remove the 2 retaining nuts for a wiring harness that is seated below the ECM module. Pay close attention to the connectors because the front and under vehicle O2 sensors have round connectors the one near the firewall has a squared connector. I was able to replace all 3 by myself in approximately 35 minutes. If your throwing a O2 heater malfunction code it is most likely going to be the sensor near the firewall. make sure that you know someone with a code reader so the code can be cleared. If you're do for an emmissions inspection be sure to put at least 40 miles on the new O2 sensor with different types of driving (e.g. highway, coasting, decellerated turns and rapid acceleration). Gotta love project cars for your kids!!
Posted on Apr 04, 2009
Tips for a great answer:
Feb 27, 2016 | Mercury Cars & Trucks
Mar 12, 2014 | 2002 Mercury Cougar
May 17, 2010 | 1999 Mercury Cougar
Mar 29, 2010 | 2000 Mercury Cougar
Mar 20, 2009 | 2002 Mercury Cougar
Mar 18, 2009 | 1999 Mercury Cougar
Feb 25, 2009 | 2000 Mercury Cougar
Jan 17, 2009 | 2001 Mercury Cougar
Dec 17, 2008 | 1991 Mercury Cougar
Mar 05, 2015 | 2002 Mercury Cougar
150 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: