Question about Cars & Trucks

1 Answer

Remove the wheel well splash shield - Cars & Trucks

Posted by on

1 Answer

ON WHAT?

Usually you can see plastic push pin you remove

There may be a few screws as well

Posted on May 10, 2014

Testimonial: "THANKS FOR A QUICK RESPONSE."

  • Rex Beene
    Rex Beene May 10, 2014

    I REALIZE THAT IT MIGHT SEEM LIKE I MIGHT BE TOO MUCH OF A NOVICE TO NOT BE ABLE TO PULL OUT THE PUSH PINS. IS THERE A PATTERN OF THE PIECES THAT YOU TAKE THEM OFF IN? I'M ON A LIMITED BUDGET AND CAN'T BE REPLACING STUPID STUFF WHEN I HAVE THE WATER PUMP, BRAKES, ROTORS, AND PROBABLY ENGINE MOUNTS. I REALLY NEED AN EXPLODED VIEW OF THE ENGINE

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locatiom of pcm 04 pacifica


REMOVAL
Behind the front left wheel splash shield 1. Disconnect the negative battery cable. 2. Raise vehicle and support. 3. Remove the left front wheel. 4. Remove the left front splash shield.


5. Unlock and remove the 4 connectors . 6. Remove the 3 mounting screws . 7. Remove the PCM.



Dec 01, 2016 | 2004 Chrysler Pacifica

1 Answer

Where is the horn location under hood of a 2007 mercury mountneer?


Remove the LH front fender splash shield !
Fender Splash Shield Removal and Installation
  1. Loosen the running board bolts and lower the running board to access the front fender moulding pin-type retainer.
    • To install, tighten to 23 Nm (17 lb-ft).
  1. Remove the lower pin-type retainer from the front fender moulding.
  1. Remove the 2 rear pin-type retainers from the front fender moulding.
  1. Position the front fender moulding aside and remove the splash shield lower screw.
    >
  1. Remove the front splash shield screws.
  1. Remove the front splash shield pin-type retainers.
  1. Remove the front splash shield.
  1. Remove the front fender splash shield.
  1. To install, reverse the removal procedure.

Mar 25, 2015 | 2007 Mercury Mountaineer

1 Answer

How do i replace rear wheel bearings


Remove tire, brake caliper, rotor, and abs sensor. Remove complete steering knuckle with hub, rotor sensor, splash shield, and bearing with seals from tie rod, strut, and ball joint. Take complete steering knuckle with hub, rotor sensor, splash shield, and bearing with seals to auto machine shop to have old bearing and seals, and rotor sensor with hub pressed out and new bearing and seals, and rotor sensor with hub pressed in. Don't forget the splash shield that fits between the the steering knuckle and rotor sensor with hub. Reassemble in reverse order. Pay special attention to abs wheel speed sensor specifications. Any further help: innovatactive@yahoo.com.

Mar 16, 2013 | 1994 Mitsubishi 3000GT

1 Answer

Need belt routing diagram for 2001 chrysler sebring lxi


Thanks for using FixYa.




jturcotte_2444.gif

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze



jturcotte_2445.gif

Fig. Accessory drive belt routing-Chrysler 2.7L engine





2.7L Engine
A/C & Alternator Belt

  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Loosen tensioner locking bolt and pivot bolt.
  4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:
  1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
  2. Adjust drive belt tension.
  3. Install the belt splash shield and right front wheel.
  4. Lower vehicle.
    jturcotte_2446.gif

    Fig. Installing A/C & alternator belt-2.7L engine


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and belt splash shield.
  4. Loosen the tensioner locking bolt and pivot bolt.
  5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:
  1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
  2. Adjust the drive belt tension.
  3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
  4. Lower the vehicle.

Power Steering Belt
  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Remove the air conditioning compressor/alternator belt.
  4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
  5. Remove the power steering belt.

To install:
  1. Install the power steering belt on pulleys.
  2. Adjust drive belt tension.
  3. Install the air conditioning compressor/alternator belt.
  4. Install the belt splash shield and right front wheel.
  5. Lower vehicle.


Oct 27, 2011 | Cars & Trucks

1 Answer

Location of battery


BATTERY LOCATION.YOU HAVE TO SAFELY RAISE SUPPORT VECHICLE ON JACKSTANDS. REMOVE THE LEFT FRONT WHEEL.THEN YOU WILL SEE A BATTERY COVER SPLASH SHIELD.REMOVE THE 4 PLASTIC FASTERNERS REMOVE THE SPLASH SHIELD.THEN YOU WILL SEE BATTERY.

Apr 14, 2011 | 2001 Dodge Stratus

1 Answer

I need to replace the alternator. How difficult is it going to be. Am I going to have to move things out of the way to get to it or is it fairly accessible?


Hi, yes, this is a pretty big job but not really hard. You have to jack up the car and go in through the wheel well to get the alternator out. Fortunately, there are good instructions at autozone.com, which I have pasted below. Please let me know if you have any questions and thanks for using FixYa.


REMOVAL & INSTALLATION See Figures 2 through 11

  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt.
  3. Raise and support the vehicle safely.
  4. Remove the right front wheel from the vehicle.
  5. Remove the right wheel inner fender splash shield.
  6. If equipped, remove the alternator dust shield attaching bolt and unclip the shield from the alternator. When removing the dust shield, be careful not to damage the rubber boot over the battery's positive terminal.
  7. Disengage the alternator field wire connector.
  8. Remove the retaining nut and wire from the positive (B+) terminal on the back of the alternator, using alternator output stud wrench SA9401C or equivalent, as a back-up wrench to prevent the stud from rotating. If the positive terminal stud rotates, the plastic insulator will crack or break, causing alternator failure.
  9. Remove the upper and lower alternator attaching bolts.
  10. Remove the alternator from the vehicle through the wheel well opening.

To install:
  1. Position the alternator in the vehicle and install the lower attaching bolt.
  2. Install the upper attaching bolt and tighten both bolts to 24 ft. lbs. (32 Nm).
  3. Engage the alternator field wire connector.
  4. Install the B+ terminal wire. The battery terminal wire should be placed on the back of the alternator between a 10 and 11 o'clock position.
  5. Be sure to use the alternator output stud wrench SA9401C to prevent the terminal stud from rotating, then tighten the alternator positive terminal nut to 89 inch lbs. (10 Nm).
  6. Install the alternator dust shield and tighten the fastener bolt to 89 inch lbs. (10 Nm).
  7. Install the serpentine drive belt.
  8. Install the wheel well splash shield and right front wheel. Tighten the wheel lugs in a criss-cross pattern to 103 ft. lbs. (140 Nm).
  9. Remove the supports and lower the vehicle.
  10. Connect the negative battery cable.


jturcotte_669.gif

Fig. Fig. 2: Compress the belt tensioner and disengage the serpentine belt, then remove it from the top of the engine compartment

jturcotte_670.gif

Fig. Fig. 3: After removing the front wheel, remove the inner fender splash shield

jturcotte_671.gif

Fig. Fig. 4: View of the alternator location with the inner fender splash shield removed

jturcotte_672.gif

Fig. Fig. 5: Loosen the alternator dust shield retaining fastener (1), being careful not to damage the dust boot over the positive battery terminal (2)

jturcotte_673.gif

Fig. Fig. 6: Remove the alternator dust shield from beneath the vehicle

jturcotte_674.gif

Fig. Fig. 7: Disengage the alternator field wire connector

jturcotte_675.gif Fig. Fig. 8: Keep the alternator output stud from rotating by holding it secure with a wrench

jturcotte_676.gif

Fig. Fig. 9: If it is more accessible, remove the upper alternator attaching bolt from the top of the engine compartment

jturcotte_677.gif

Fig. Fig. 10: Remove the lower alternator attaching bolt from beneath the vehicle

jturcotte_678.gif

Fig. Fig. 11: Remove the alternator through the wheel well opening

Dec 30, 2010 | 1996 Saturn SL

2 Answers

How do you remove the tesion pulley on a 93 saturn sl2 there is no room to get in there and remove it


Raise the right front wheel off the ground and support that corner of the car on a jackstand. Remove the right front wheel. Remove the inner splash shield. The splash shield is held in place with numerous black plastic clips- the center of the clip needs to be pulled part way out, then the entire clip is removed. After the splash shield is remove you get good access to the tensioner and it's mounting bolts.

Nov 01, 2009 | 1993 Saturn SL2

1 Answer

How do I get to the drivers side marker light bulb


  1. Remove the inner wheel well splash shield.
  2. Grasp the bulb socket and rotate it counter-clockwise to remove it from the lamp.
  3. Remove the bulb from the socket.
  4. Installation is the reverse of removal.
b2159df.gif
Remove the retaining bolts for the splash shield and ...

aa616ff.gif
... remove the splash shield from the vehicle

470117c.gif
Twist the bulb socket to remove it from the lamp and ...

61c885a.gif
... lower the socket down to access the bulb

fd06434.gif
Pull the bulb straight out to remove it from the socket

Oct 10, 2009 | 1997 Chevrolet Cavalier

1 Answer

How to 1998 Taurus altenator R&R


please rate highly if this helps
Generator 3.0L (2V)
Removal
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  2. Remove the right front wheel. Refer to Section 00-02 .
  3. Remove the lower fender splash shield retainers and position the shield out of the way.
  4. Lower the vehicle.
  5. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  6. Remove the power steering line bracket and heater hose support bracket from the generator.
  7. Remove the upper generator bolts.
  8. Remove the generator splash shield.
  9. Raise the vehicle.
  10. Disconnect the electrical connector and remove the battery positive cable from the generator.
  11. Position an adjustable stand to the subframe.
  12. Remove the right subframe bolts.
  13. Remove the lower generator bolt.
  14. Disconnect the right hand stabilizer link.
  15. Lower the subframe to provide clearance.
  16. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Connect the right hand stabilizer link and torque to 47-62 Nm (35-46 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B + cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
3.0L (4V)
Removal
  1. Disconnect the battery ground cable. For additional information, refer to Section 14-01 .
  1. Remove the accessory drive belt from the generator pulley. Refer to Section 03-05 .
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist. Refer to Section 00-02 .
  1. Remove the right front wheel. Refer to Section 00-02 .
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Section 03-05 .
  1. Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.
3.4L (4V)
Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the right side cowl vent screen. Refer to Section 01-02 .
  1. Raise the vehicle and remove right front wheel assembly. Refer to Section 00-02 .
  1. Remove right tie-rod. Refer to Section 11-02 .
  1. Remove accessory drive belt (8620) from generator. Refer to Section 03-05 .
  1. Disconnect electrical harness connector and output terminal wiring.
  1. Remove nut and position engine control sensor wiring (12A581) out of the way.
  1. Remove the two bolts and one stud bolt.
  1. Remove generator from vehcile

May 12, 2009 | 1998 Ford Taurus

1 Answer

Dont know location of computer


The PCM is located behind the right front fender splash shield, you wheel need to remove the right front wheel and splash shield to gain access to it.

Aug 03, 2008 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...