Question about 1998 Oldsmobile Intrigue

1 Answer

Olds intrigue recalls

Window wiper pulse module board was replaced to operate wipers.wipers work fine however,they won't shut off.is there asolution to this problem.can you me,thank you.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 247 Answers

Replace wiper switch or bring it to your dealer.

Posted on May 10, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

the recycler
  • 22 Answers

SOURCE: Wipers stop after 5 minutes of slow or intermiant speed use.

Try replacing the Wiper Motor Pulse Board Module. It is available at aftermarket parts stores, it is easy to replace, and it is a high failure item. Eventually, the module will fail completely and leave you with no wipers.

Posted on Feb 25, 2009

  • 4 Answers

SOURCE: Wiper does not stop wiping until engine shut-off

you need to replace multi function switch

Posted on May 08, 2009

  • 16 Answers

SOURCE: my '98 olds intrigue has wiper problems

My best solution, which you may not want to hear is new wiper motors. It seems like a common thing in these cars (the wipes don't go down all the way.

Posted on Jul 22, 2010

  • 611 Answers

SOURCE: 2002 Olds Intrigue ...sometimes the

usually its both the switch and the pulse usually go bad at the same time but u can start with wiper motor with pulse board try rockauto.comtheyre best for parts

Posted on Sep 20, 2011

  • 33250 Answers

SOURCE: My '98 Olds Intrigue passenger wiper quit. The driver side works fine. What to do?

The wiper arm fastens to a rotating shaft at the bottom. The arm may have loosened and needs to be tightened. Also could be a problem with the wiper linkage.

Posted on Sep 05, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 trialblazer rear window wiper inop. changed switch and motor. no power to motor. cannot find relay nor fuse


There are something's involved that you are not aware of , or familiar with . Electronic control modules .
Rear Wiper/Washer System Controls
• Body control module (BCM)
• Liftgate control module (LGM)
• Rear wiper/washer switch
Do you know what a serial data network is ?
Rear Wiper/Washer System Operation
The rear window wiper/washer switch is an input to the BCM. The requested rear wiper mode is sent to the liftgate control module (LGM) by the BCM as a message on the serial data circuit, and the rear window wiper motor is controlled by the LGM. The switch power circuit to the rear wiper/washer switch is a 12-volt reference supplied by the BCM during ignition on, accessory or RAP power modes. The rear wiper/washer switch is a series of resistors and the switch position is determined by the voltage of the rear wiper/washer switch signal circuit to the BCM. The rear wiper/washer switch has continuity at all times and the BCM expects a rear wiper/washer switch signal voltage in all switch positions including OFF. The rear wiper motor is supplied battery positive voltage and ground. The LGM controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the LGM. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode. The liftglass and liftgate ajar switches are inputs to the LGM and must be in an inactive state in order for rear wiper washer system operation to be enabled. When an ajar switch is active the LGM suspends wiper motor operation directly and sends the ajar switch status messages over the serial data circuit enabling the BCM to suspend washer pump operation. The rear window washer pump is controlled by the BCM through the rear washer relay. Battery positive voltage is supplied to the coil and switch sides of the rear washer relay. When the rear window wash request is active the BCM energizes the relay by grounding the relay coil through the rear washer relay control circuit. When the relay is energized battery positive voltage to the relay switch is supplied to the washer pump control circuit.

Your best bet , take it to a qualified repair shop and have it checked for DTC'S - diagnostic trouble codes .
DTC B1017 or B3970
The rear wiper motor is supplied battery positive voltage and ground. The liftgate control module controls rear wiper motor operation through the rear wiper motor control circuit. The rear wiper motor control circuit is supplied a battery positive reference voltage by the rear wiper motor module and is pulse width modulated to ground by the liftgate control module. The duty cycle of the pulse width modulation determines the rear wiper motor operating mode.
DTC B3799

2
Turn the ignition ON.
Operate the rear wiper switch through all the switch positions.
Does the rear window wiper operate normally?
--
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Install a scan tool.
Display the liftgate control module data list.
Observe the following parameters while operating the respective switches. Refer to Scan Tool Data List for typical values.
• Liftgate Ajar Switch
• Liftglass Ajar Switch
Did the scan tool indicate the correct switch positions?
--
Go to Step 4
Go to Courtesy Lamps Inoperative in Lighting Systems
4
Observe the requested rear wiper parameter in LGM data list.
Operate the rear wiper switch through all the switch positions.
Does the scan tool indicate the correct requested rear wiper parameter in relation to the switch position?
--
Go to Step 5
Go to Step 6

Feb 06, 2017 | 2002 Chevrolet TrailBlazer

1 Answer

1999 Pontiac Grand Prix wipers will not turn off


replace the arm it's self. take the streering wheel..

Jan 29, 2014 | 1999 Pontiac Grand Prix

1 Answer

1984 buick lesaber wipers stoped pulsing


Usually when the delay function fails, the problem is in the circuit board module on the wiper motor.
You would need to check the circuit with a meter, the module may be available without buying a wiper motor.

Feb 08, 2013 | 1984 Buick LeSabre

1 Answer

2002 Olds Intrigue ...sometimes the wipers start by themselves with the switch in the off position. The only way to shut them off is to push the washer button.(sometimes takes 3 or 4 tries).-do you think...


usually its both the switch and the pulse usually go bad at the same time but u can start with wiper motor with pulse board try rockauto.comtheyre best for parts

Sep 14, 2011 | Oldsmobile Intrigue Cars & Trucks

1 Answer

Can you please give me instructions on replacing the wiper motor pulse board module on my 95 Chevy Van G20?


This is a very simple procedure and will save you lots of money by replacing it yourself! A common replacement item on GM vehicles, it should be readily available at your local auto parts retailer and should take no more than a half-hour with just a couple of tools.


• Turn the ignition key to the OFF position.
• Remove the Connector Position Assurance (CPA) and disconnect the wiper motor electrical connector.
atye.gif
• Remove the three screws that secure the cover to the wiper motor and remove the cover.
• Inspect for sealant on the inside of the cover and then discard the cover and screws. Important: If sealant was found on the old cover, it will be necessary to remove any old sealant from the motor housing in Step 6.
• Carefully remove the module (circuit board) from the wiper motor by lifting up on the end of the module electrical connector.
• If necessary, remove any old sealant from the wiper motor housing (refer to Step 4). Notice: When handling the new module in the next step, be careful not to damage or band the electrical contacts on the bottom side of the module.
• Install the module into the wiper motor housing, making sure that the module is fully seated. When fully seated, the edges of the module circuit board will be flush (even) with the motor housing along all sides.
atye_0.gif
• Carefully apply a bead of silicone sealant, P/N 12345739 (or GE-162 sealant or equivalent) in the groove of the NEW cover (Figure 2). Remove any excess sealant that is outside of the groove. Important: Only apply enough sealant to fill the groove in the cover.
Install the new cover on the wiper motor housing and install the three new screws.
• Tighten the screws to 2.6 N·m (23 lb in).
• Reconnect the wiper motor electrical connector to the wiper motor assembly and install the CPA.
• Turn the ignition key to the ON position and check the wiper system for proper operation (delay/low/high/etc.).



May 04, 2011 | Chevrolet G20 Cars & Trucks

2 Answers

My wipers work when they want to don't always work when it's raining. Is there a recall on the windshield wiper motor for a 1997 Chevy Blazer?


I don't believe there is a recall but I've replaced a lot of the wiper control modules [glorified circuit board] on top of the wiper motor for similar problems. Something in the circuit board goes bad and causes the wipers to malfunction randomly. There are other things that can cause wipers not to work but I'd look there first

Jun 10, 2010 | 1997 Chevrolet Blazer

10 Answers

Windshield wipers will not turn off - 2003 Chevrolet Silverado


Fixed the wiper problem which was identical to Brad's by changing out the wiper module which is also called a pulse module or something of that nature. Pretty easy fix. You have to remove the grill that the wiper blades protrudes from in order to get to the motor (4 clips in front which can be removed by hand, remove radio antenna, a center push down retainer, two plastic end caps which pop off and then 1 star type screw on each end under the end caps). Getting the blades off seemed difficult. I used a small puller to pop them off after removing the nuts.

You can't buy this module at a regular parts store. I had to get it from the dealer so be prepared to spend $130 to $140 for the part or go to the salvage yard. Works great now.

Mar 14, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Wipers stop after 5 minutes of slow or intermiant speed use.


Try replacing the Wiper Motor Pulse Board Module. It is available at aftermarket parts stores, it is easy to replace, and it is a high failure item. Eventually, the module will fail completely and leave you with no wipers.

Feb 25, 2009 | 2001 Oldsmobile Intrigue

3 Answers

I have a 2003 Chevy Trailblazer Windshield Wiper problem.


As it turns out, there is a recall On 2002-2003 Chevy Trail Blazer's
Windshield Wiper/washer
NHTSA No. 04V046000
Recall Date: Feb, 4th, 2004
Call your dealer to see if this is still under the recall to be fixed.
RECALL: 2002 - 2003 Chevrolet Trailblazer NHTSA Campaign Number: 04V046000 www.nhtsa.dot.gov
Manufacturer GENERAL MOTORS CORP. Recall Date: FEB 02, 2004 Potential Number Of Units Affected: 581394 Description VISIBILITY:WINDSHIELD WIPER/WASHER Summary CERTAIN SPORT UTILITY VEHICLES HAVE WINDSHIELD WIPER SYSTEMS THAT WILL NOT TURN ON, CEASE OPERATION WHILE IN USE, FAIL TO TURN OFF/ON BY THEMSELVES (MOISTURE SENSITIVE WIPER SYSTEM), OR HAVE CONTINUOUS WINDSHIELD WASHER PUMP OPERATION BECAUSE THE PRESENCE OF WATER WITHIN THE WIPER MODULES CAN EITHER CAUSE A SHORT CIRCUIT OR CAN LEAD TO THE CORROSION OF COMPONENTS WITHIN THE MODULE. Consequence DEPENDING ON THE OCCURRENCE AND WEATHER SITUATION, DRIVER VISIBILITY COULD BE REDUCED, WHICH COULD RESULT IN A CRASH. Remedy DEALERS WILL COVER THE WINDSHIELD WIPER MODULE VENT HOLE WITH A PATCH. ALSO, THE WIPER MOTOR, CIRCUIT BOARD, AND ELECTRICAL CONNECTOR WILL BE INSPECTED TO SIGNS OF WATER INTRUSION AND/OR CORROSION AND BE REPLACED AS REQUIRED. THE RECALL BEGAN JULY 6, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438; OLDSMOBILE AT 1-800-630-6537; OR GMC AT 1-866-996-9463.

Nov 25, 2008 | 2003 Chevrolet TrailBlazer

4 Answers

Need wiring diagram


i dont think u need a wiring diagram. you should check your wiper motor circuit board first. on my 94 s10 the wipers either worked when they wanted to and now they dont work at all. just either replace the circuit board yourself ($19.95 on ebay) or replace the whole wiper motor ($60 on ebay) and your wipers should work. just give this a shot as its a good place to start. i myself am going to replace the wiper circuit board as its cheap, and really easy to access and replace. all you need is a screw driver. good luck. and no, im not a GM Technician. just owned my truck since day 1 and always try to check vehicle forums for answers first.

Aug 01, 2008 | 1994 Chevrolet S-10

Not finding what you are looking for?
1998 Oldsmobile Intrigue Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...