Question about Cars & Trucks

1 Answer

Will a transmission from a 1998 ford Taurus gl work in a 1997 ford Taurus gl both are ax4n transmission

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Cars & Trucks Expert
  • 139 Answers

As long as its the same model then yes

Posted on May 10, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: 97 taurus GL inner tie rods

You have to have a special tool like this
http://motors.shop.ebay.com/items/Parts-Accessories_Automotive-Tools__W0QQ_nkwZfordQ20innerQ20tieQ20rodQ20toolQQ_fromfsbZQQ_trksidZm270Q2el1313QQ_odkwZQQ_osacatZPartsQ2dAccessoriesQ5fAutomotiveQ2dTools

Disconnect the outer tie rod and remove,then remove boot,then use special tool to remove inner tie rod. You will then have to have it aligned. You can use a tape measure to get it close enough to drive,just mark one of the grooves in the tire so you are measuring the exact same points,measure from tire to tire in the front of front tires then take a measurement at the rear of front tires and adjust the outer tire rods until the measurements are pretty close to equal.

Posted on Feb 17, 2009

chuck943
  • 783 Answers

SOURCE: obd code p0133 and p01131

P1131 bank 1 indicates the fuel/air ratio is correcting rich for an overly lean condition.
Diagnostic Trouble Codes (DTCs) P0133 and P0153 indicates the response rate of the upstream HO2S(s) is below some calibrated window. The test measures the HO2S amplitude and output frequency. This is accomplished by superimposing a 1.5 to 2.5 Hz square wave over Lambse. The HO2S switching is monitored during this time to see if the calibration limit is met. P0133 is also bank 1.
Although these codes could be caused by several things such as vacuum leaks,fuel contamination,exhaust leaks,miss-fires,etc. Since it is localized on only bank one I would replace that front(upper in the exhaust to back cylinder head) 02 sensor and see if that did not correct my concern.

Posted on Mar 12, 2009

chuck943
  • 783 Answers

SOURCE: I need to find a fuse diagram for a 1997 ford taurus gl.

http://www.genuineservice.com/genuineservice/en/default?page=genuineService

Go to this website on left hand task bar pick owner guide,input vehicle information and go to owner guide. The fuse information starts on page 100.

Posted on Mar 12, 2009

  • 4 Answers

SOURCE: Ford Taurus Transmission Removal step by step

its quite a job, but hopefully this helps you, i have already replaced my gfs transmission on her 2000 taurus once and i need to do it again, ford really sucked on these transmissions. if you jack up the car high enough to give you about 21/2 feet of pllay under the car it would be good, take the tires off, take the calipers off, disc brakes, nut on axles, rack and pinion to the spindle, shocks, everything that will get in the way when you bring down the bottom frame. under the hood, i take out the intake air box and battery with battery plate so it gives you room to disconnect the shift cable and all connections that need to be disconnected. now remember when you bring down this frame its going to come down with motor and tranny, so you gotta either get an engine hoist or put some blocks under the mottor,take the starter off, take the torque converter cover off from the bottom its right in the middle of the motor and tranny 2 screws, there are 4 nuts honding the torque converter in there so you will probably need the help of someone to turn the main pulley as you look for those 4 nuts, take all bolts holding the transmission in place, take axles off, 2 big nuts for the rack and pinion, 2 nuts for motor mounts (if you are under the car they are holding onto the squared frame, use a engine hoist to hold on to the motor and use a jack under to hold the tranny, now this is the tricky part, you might want to use a second jack to hold the frame, as you take off the 4 main bolts for the bottom frame leave one so it dosent come crashing down, if you have everything secure, take the last bolt off as you have the jack holding it in the front in place, when you take it off then bring the jack down slowly making sure you got all bolts and connections, once that is down make sure all bolts and connections are disconnected from transmission, there are 2 metal hoses that go into the front of the transmission that are a pain to get out, squeeze the 2 little plastic ears that it has as you try to pull the tip out, play with it cause sometimes they are a pain, once you have that, double check everything and you can wiggle the tranny to make sure its loose off the motor if it is, take precaution and bring the jack down slow to bring your transmition down. hope it helps if you know some basics of mechanical.

Posted on Jul 15, 2010

  • 118 Answers

SOURCE: Does 1997 Ford Taurus GL

Chain.

Posted on Aug 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 taurus ax4n tranny


You might need to replace the valve body clip with the upgraded (stronger) one. Ford had problems for a while with the clip breaking and not allowing the tranny to shift into O/D. I had the no O/D problem, I replaced the clip with the upgraded (stronger) one which fixed the problem.

fix with this kit
Sonnax 96206-07K AX4N 4F50N Transmission forward control valve, Transmissionpartsusa.com

Below are the DTC codes if it has any. ISSUE
No 4th gear operation (no 3-4 shift) and Diagnostic Trouble Codes (DTCs) P0734 and/or P0761 or 648 may occur on some vehicles.

Nov 19, 2013 | 1996 Ford Taurus

1 Answer

Will a 1999ford Taurus transmission will fit in a 1995 Winstar van


No it will not, there are two transmissions availiable in both of those vehicles AX4S and AX4N.Both of these transmission had changes in 1997 that will keep them from retro fitting back.Also they will not interchange between each other because of different lengths and are wired differently.

Mar 08, 2011 | 1995 Ford Windstar

1 Answer

1996 ford taurus ax4n transmission. front seal replacement.


my overdrive isnt working when it worked in the car it came out of

Oct 16, 2010 | 1996 Ford Taurus

1 Answer

I need a new Trans for a 1996 ford Taurus GL wagon.


The best way is to use the vehicle VIN number, here is a link to a Ford Vin Number Look-up site, that will tell you the transmission code and the type of transmission you have:
https://www.fleet.ford.com/maintenance/vin_tools/default.asp

May 23, 2010 | 1996 Ford Taurus

1 Answer

Could you please tell me how a changeover transmission would be for a 96 Ford Taurus


O.k. I don't know what a changeover transmission is. Are you talking about a remanufactured transmission? The transmission in a 1996 Taurus would be a AXOD-E or a AX4N. Not sure about the price. I would guess about 1600-1800 dollars.

Apr 15, 2010 | 1996 Ford Taurus

2 Answers

Will a transmission #ax4s from 1988 ford windstar fit a 200 windstar with transmission # ax4s


I dont think that will work ....1988 was aod and aode trans

The AXOD-E was renamed AX4S in 1993. In addition to the name change, improvements in the lubrication of the gearset and capacity upgrades were made. A centrifugal piston assembly was implemented in the intermediate clutch position to improve 1st-2nd and 2nd-1st shift quality and an increase in the clutch's durability was made on some models. High energy friction materials were also introduced. A new twin piston torque converter clutch (TCC) was introduced with the AX4S and the AX4N on some models. The transaxle pan on this model will sometimes read "AXOD Metric" since it's based on the AXOD transaxle. The data plate code for this transmission is "L."
Applications:
The Ford AX4S automatic transmission is a four-speed electronic overdrive transmission used in 1995 to 2000 Ford Windstar minivan. The transmission is also used in 1991 to 2003 Ford Taurus and Mercury Sable, and 1993 to 1995 Ford Taurus SHO models. The AX4S is a second-generation version of the AXOD and AXOD-E transmissions used in 1986 to 1991 Ford Taurus.

Nov 16, 2009 | 2001 Ford Windstar

1 Answer

Speedometer


with the speedometer it could be a bad sending unit located on the left side of the transmission near the cv axle. or that the guage is faulty, or a loose connection. your transmission is a AX4N Metric if it's an automatic. the sending unit is a dealer only item and costs about 60 dollars it is not cable driven but has an electrical harness to it. as far as the hard steering it could be that your power steering pump is bad, you have a blockage in your rack and pinion unit, or there is air in the system

May 19, 2009 | 1998 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...