Question about 2000 Ford Ranger SuperCab

1 Answer

Where is egrpressurefeedback sensor located on a 1999 ford ranger 2.5l

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 156 Answers

I believe it's on the right hand side near tranny dipstick. .simple thing to do is follow the egr steel exhaust tube from the back of the motor, the D.P.F.E will be off of that tube connected with 2 black rubber hoses and have a single electric connection.

Posted on Jun 20, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Ajkill
  • 2035 Answers

SOURCE: 2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???

Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Posted on Jan 16, 2009

  • 1 Answer

SOURCE: O reading for O2 sensors on 98 Ranger XLT

Yes the 98 ranger has 3 02 sensors,they are located in the exhaust system under vehicle,2 of them
are in front of the cataletic converter and 1 behind it.I replaced mine ,reset the codes and the check
engine light still comes on?

Posted on Jan 19, 2009

the recycler
  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

the recycler
  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

lacroixx1
  • 101 Answers

SOURCE: 1999 ford ranger 4.0 engine code p1151

are all codes for the o2 sensor

Posted on Jun 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace a egr pressure feedback sensor on a 1999 ford ranger


it maybe a metal sensor, which has been replaced with a plastic sensor. not hard to change, however make sure the two hoses are in good shape, no cracks etc. may mount with two 7 mm screws. be careful...jim

May 09, 2014 | 1999 Ford Ranger SuperCab

1 Answer

1999 Ranger IAC and PCM problems


i would start looking for vacuum leaks first,

Jun 20, 2012 | 1999 Ford Ranger SuperCab

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

1 Answer

2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???


Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Jan 16, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

O reading for O2 sensors on 98 Ranger XLT


Yes the 98 ranger has 3 02 sensors,they are located in the exhaust system under vehicle,2 of them
are in front of the cataletic converter and 1 behind it.I replaced mine ,reset the codes and the check
engine light still comes on?

Jan 16, 2009 | 2004 Ford Ranger

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...