Question about Renault Kangoo

1 Answer

How two find tdc on my van

Never marked the belt like a nob now i need no how 2 find tdc on the crank does any 1 no any easy way 2 fix pls

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Renault Expert
  • 403 Answers

It should be easy but if worst comes to worst can you move the crank and take number 1 plug out with a rod in the hole of the plug turn it up or down the crank until the stick or rod goes up and check the marks on the crank pulley with the top pulleys

Posted on Jun 18, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 37 Answers

SOURCE: 1991 mazda b2200- timing belt changed

The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Posted on Dec 13, 2008

ewashmidas
  • 362 Answers

SOURCE: Fitting n13 timing belt

A 1990 Nissan Pulsar has a timing chain, not a belt. Here is the picture.
a4e2a04.png

Posted on Mar 14, 2009

  • 170 Answers

SOURCE: I removed the timming belt of a fiat uno 1983-1985

PULL OUT NO 1 SPARK PLUG PUT A SCREW DRIVER DOWN THE HOLE AND TURN THE ENGINE OVER BY HAND UNTIL THE SCREW DRIVER IS AT THE TOP THEN YO WILL SEE THE MARKS ON THE CRANK OR LOOK AT THE TIMMING COVER IT SHOULD SHOW YOU TDC

Posted on Aug 31, 2009

  • 114 Answers

SOURCE: 1997AudiA6Quatro2.8L-aligning cam and crankshaft for timing belt

You must find the cam lock bar and crank lock pin to do this job properly, otherwise you can bend some valves and that becomes expensive..the front crank damper has a mark to line up with a mark on the timing cover for #1 TDC, but the cam lock bar is what aligns the cams into position. The crank lock pin is helpful but not 100% necessary...

Posted on Sep 16, 2009

emissionwiz
  • 76846 Answers

SOURCE: 1992 Volvo 960 Broken timing belt

IF U BROKE THIS BELT WHILE DRIVING U HAVE BENT THE VALVES IN THE ENGINE, THIS IS WHAT IS CALLED AN INTERFERENCE DESIGN ENGINE, THAT MEANS WHEN THE TIMING BELT BREAKS THE PISTONS HIT THE ENGINES VALVES

Posted on Nov 11, 2009

Testimonial: "THanks - was not able to accept this last answer, but thankfully I found another way to say THANKS. That notch was suspicious!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could have happened?


I would do a leakage test on the suspect cylinder and compare with a couple others.

Mar 10, 2016 | 1999 Ford Escort

1 Answer

What needs to b done if a 1.6L suzuki engine was accidentally cranked one short/quick turn while the timing belt ra's removed? ?? Haynes book only mentions NOT to turn engine w/belt off, but says NOTHING...


wOW NO YEAR STATED, 89-99> n o caar stated either,
so I guess G16a or G16b engine.... why must i guess.... lots of 1.6 by suzuki made.....
nothing, its free running, most G16s are.
cant speak for all 8 cams sold world wide, but stock USA
its free running. why not put the crank at TDC #1 firing
and turn cam by hand and feel, (reality) look ma, no hitting....

that warning is just Haynes (junk book) stating what is printed
on all real SUZ. OEM FSM books, it states this.
http://www.fixkick.com/t-belt/interference.jpg

and is a worldly warning, on all engine they sell world wide all 56 engines sold.

most G16 are free running SOHC , usually are and rare DOHC.
most authorities, all that ive seen and seen most all mimic
the above factory warning, but what else can they do..
they read it and its CLEAR , no?

now your question, sure it dont say what to do
after all they dont know where you left the cam,

if super paranoid, (been there)
we do this,
put crank TDC, mark, (fires every 180 degrees it does)
the turn pulley to 90degrees, this puts all pistons 1/2 up.
now drop the head on to block with , cam cog with E mark at 12pm.
this is #4 firing.
now back the crank up CCW 90%
now #4 is firing.

easy huh> ?
note how the G16 has 2 heads, and are done DIFFERENTLY.
http://www.fixkick.com/t-belt/tbelt-index.html#Tbelt-main

if not paranoid?
put crank to TDC mark, 0deg
put cam cog to E mark up(16v). or pimple mark up(8v) 12pm
there is a 12pm mark on top back of cam cog
this is #4 firing, an is where all G16s are timed. (ALL)
end story.
there are false marks ,fully documented in link for 4 engines.
(they changed marks 4 times)

Mar 16, 2015 | Suzuki Cars & Trucks

1 Answer

How do I reset the timing?


First pull the timing belt tensioner then slip the belt off the cam gears. You then need to find TDC (Top dead center). 3 ways to find TDC 1) There are marks on the crank pulley align them for TDC. 2) Remove timing cover and use crank gear mark seen in link below 3) Put the dip stick in cylinder 1 and turn engine until dip stick stops going up. After finding TDC align cam gear marks seen in link below. Now make sure both cam and crank stay in position and slip timing belt back on (you can move the cam gear to get the belt on but make sure the marks are aligned after the belt is on). Last tighten the belt tensioner, I usually use my finger or an extension to get some more tension on the belt. You might have to remove engine mount bracket makes life much easier as the front cover section is TIGHT !!!. Turn engine a few times to make sure you have compression and engine turns without getting stuck. See link below good luck.

http://bladeagenos21.soup.io/post/374487151/timing-marks-on-mazda-626-1994-diagram

Jul 08, 2014 | 2002 Mazda 626

1 Answer

How to change a timing belt


You may follow these steps:

1. Remove any shrouding in the wheel so that you can access the lower timing belt pulley and the crankshaft snout.

2. Locate the timing marks on the flywheel and cam, then you set them both to TDC. The flywheel pulley TDC mark is accessible through a hole in the bellhousing. The camshaft TDC is easy to locate, especially if you added some marks.

3. Support the engine with something like skyhook if you want to remove the rightside motor mount. Most belts are installed with a mount in the center, making them problematic when changing. You can now remove the motor mount temporarily.

4. Freeing up the belt tensioner pulley can release any belt tension.

5. Slip through the new belt into place and make sure that you are not disturbing the cam or crank pulleys, or else the engine will be out of time if changes and adjustments are made. Then check by slowly rotating the crank to two full turns with a socket on the crank snout.

Sep 12, 2012 | 1997 Buick Skylark

1 Answer

How do i set the valve timing if i cant see the timing marks on a VW 1.8 20valve golf cylinder head timing chain , i can only find the one on the belt side i have put the cam on TDC for the ex-valve but...


The 2 cams are linked with a chain at the rear of the cylinder head.

The cams need to be set so the slots on the chain sprockets line up with the cam tower caps with 16 links between cam caps.

You cannot see the front crank pulley tdc mark so you need to lock the engine at tdc with a screwdriver jammed into the timing hole on the bell housing after setting engine at tdc or use a DTI
to check to tdc in the #1 spark plug hole.

If the cams have not been disturbed you only need to set the belt cam sprocket to the mark and crank to tdc.....all this means pulling the core support into the service position so the belt tensioner can be locked down and/or doing a complete belt job along with a coolant pump if over 70,000 miles..

Aug 20, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

When it is in time were are the time mark be at cams & cranke


You will need the manual to see where the timing marks are.The timing marks should have been aligned before you removed the old belt.In short,how to do it is find #1 cyl tdc,both valves closed,look at the camshafts and there will be 2 marks one is marked "E",the othe"I"These 2 marks vary on each engine and its a must to have the correct setting which is only in the manual.With the crank set at TDC,both cams aligned ,then reset your belt.Dont forget to allow for the tensioner when you release the tension as the cams will turn slightly.I would recommend getting the book as you will never get it right without it.For $20,its a good investment

Feb 07, 2011 | 1998 Mazda MPV

1 Answer

I have a 2.3 how do i install the timing belt


Align harmonic damper mark at TDC with #1 piston at top. You'll have to remove harmonic damper on front of crank. (You can do it without removing the damper, but it's a real pain in the rear.) This WILL require an industrial strength impact wrench to break the bolt loose. Pull spark plugs. Makes last step easy and you can use a screwdriver to make sure #1 is at top. You'll see tick marks on the crank pulley, the cam pulley and the auxillary shaft pulley. These marks must line up. Use a straight edge (ruler, piece of flat metal stock, etc.) to make sure they're aligned. Pull tensioner arm back and lock it there. Install belt around pullies. Now comes the tricky part. Whne you release the tensioner, the auxillary shaft will rotate at least one tooth off of alignment. Release tension and compensate auxillary shaft postion. You want the marks aligned with the belt under tension. Now using a long wrench, rotate the engine clockwise by turning the crank balancer bolt. After 2 complete revolutions back to TDC, confirm timing mark alignment on the pullies. If they're off, redo it until they're aligned. Good luck.

Oct 14, 2009 | 1996 Ford Ranger SuperCab

2 Answers

1990 LEXUS LS400 T-SHIRT GOT CAUGHT BETWEEN TIMING BELT AND CAMSHAFT GEAR(DONT ASK I STILL CANT GET OVER IT)ANYHOW i GOT THE SHIRT OUT BUT WHEN I GO AND PUT THE CRANK AT 0 AND THE ROTOR POINTING AT THE #1...


take the timing belt off reset the crank at 0 with # 1 piston at TDC ensure that both cams are up at twelve 'oclock with belt on, when the tension is released and the tensioner is tightened turn the crank atleast 360 degrees and ensure that the timing does not shift before starting engine

Aug 19, 2009 | 1990 Lexus LS 400

1 Answer

1997AudiA6Quatro2.8L-aligning cam and crankshaft for timing belt


You must find the cam lock bar and crank lock pin to do this job properly, otherwise you can bend some valves and that becomes expensive..the front crank damper has a mark to line up with a mark on the timing cover for #1 TDC, but the cam lock bar is what aligns the cams into position. The crank lock pin is helpful but not 100% necessary...

Aug 15, 2009 | 1997 Audi A6

2 Answers

1991 mazda b2200- timing belt changed


The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Nov 09, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

xxxxxx xxx

Level 3 Expert

4874 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...