2001 ISUZU 3.5L V6 HEAD TORQUE? - 1990 Isuzu Spacecab

6ya staff

• 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

6ya - Get Instant Help

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

SOURCE: what is the 98 isuzu rodeo head bolt torque

joyce, there are different specs for sohc and dohc engines. my advice is to get a Haynes manual from the auto parts store.

doug

Posted on Sep 01, 2008

Scotty

• 104 Answers

SOURCE: TORQUE SETTINGS ISUZU RODEO FOUR CYLINDER

I dont know the specific answer for your question, but I own a 1995 Rodeo and there is an online community you could probably check out that Im sure would have the answer for you.

Check out www.planetisuzoo.com, sign up and post your question there. There are several knowledgeable people there and some good information as well.

Posted on Jan 03, 2009

yadayada

• 78267 Answers

SOURCE: i need torque specs for 94 rodeo

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Posted on Feb 14, 2009

Greg Bernett

• 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

mx5turbo92

• 545 Answers

SOURCE: i'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.

1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
2. Clean the rod bearings and the crankshaft pins.
1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
3. Remove the rod caps.
1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
2. Clean the plastigage from the bearings and the crankshaft pins.

Posted on Jun 04, 2009