Question about Cars & Trucks

1 Answer

Thermostat 2006 ford e350 6.0 diesl - Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

TAKE IT TO A REPUTABLE SHOP

Posted on May 09, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the recommended oil for diesl engin 2006 5speed manual


Rotella or Chevon Dello 400. Both are good but I prefer Rotella.

Nov 26, 2016 | Cars & Trucks

1 Answer

How to change a thermostat on a 2006 Ford Escape


Follow the lower radiator hose to where it enters the top of the engine, that is where your thermostat housing is. It should only be 2 or 3 bolts to pull off the housing and pop out the thermostat. You will need to drain the coolant from the system by disconnecting the hose exiting the radiator.

Mar 13, 2015 | 2006 Ford Escape

1 Answer

6.0turbo diesl no heat coming in two cab


This problem may be as simple as a low antifreeze level, or the worst alternative is that possibly your heater coil went bad.

Feb 14, 2015 | 2006 Ford F-250 Super Duty

1 Answer

Does a 2006 pontiac montana minivan have an inline fuel filter if so where is the location of it


no idea but if it runs ok leave well alone ,never changed a fuel filter on a petrol engine in donkeys years ,diesles yes but a petrol ?

Aug 23, 2013 | Cars & Trucks

1 Answer

Where is the thermostat in a 2006 ford focus i ned to replace it


The upper radiator hose is connected to it. Follow the hose and youll find the thermostat housing. You may have to move the coil pack to get to the housing to change out the thermostat. I found a quick step by step here: http://www.ehow.com/how_4484915_change-thermostat-ford-focus.html
Hope this helps you...

Mar 28, 2011 | 2006 Ford Focus

2 Answers

What is error code P0128 on 2006 Ford Fusion SE, 4 cyl, auto


P0128 is the fault code to check 1.the coolant level 2. thermostat defective 3. ECT (engine coolant temperature) sensor defective

Nov 13, 2010 | 2006 Ford Fusion

2 Answers

How do you fix a P0128 code on a 2006 Ford Fusion?


Upstream HO2S Sensors Swapped or this one
P0128....Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) now if this a 2006 model built for the europeon market then your code reader is a waste of time as it will never read the correct codes and if your really lucky it could lock up the immobilisor as well this is to prevent general garages from doing any repairs so just take it back to a ford garage

Jul 30, 2010 | 2006 Ford Fusion

1 Answer

Are there any online instructions for replacing the thermostat on the 2006 ford fusion 4 cyl. thank you much!


2.3L Engine
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the 3 bolts and reposition the thermostat housing to gain access to the hose clamps.
  4. Remove and discard the gasket.
    • To install, tighten the bolts to 10 Nm (89 lb-in).
  5. Disconnect the heater hose from the thermostat housing.
  6. Disconnect the lower radiator hose from the thermostat housing and remove the thermostat housing.

6efb7cd.gif
Thermostat housing and related components—2.3L engine

To install:
  1. To install, reverse the removal procedure.
  2. Install a new thermostat housing gasket.
  3. Fill and bleed the cooling system

Dec 07, 2009 | 2006 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...