Question about 1991 Isuzu Rodeo

1 Answer

I'm trying to remove the rear passenger side axle or what is remaining of it when it snaped in half. what all do i have to remove before the axle will slide out? I think I've found the snap ring but it has a half inch gap in it and I can't find the holes that my snap ring removal tool is supose to fit into. Are there any other bolts or parts needed to be removed before I can get to the snap ring?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

A 91 has a gm type rear end in it. The rear end cover has to be removed along with the pinion gear shaft. The axles are held in with two C -clips that must be removed to get them out.

Posted on Jun 23, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Removing rear axle shaft


Aug 19, 2014 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

How do you change the rear axle seal

This is a c clip axle remove diff cover rotate carrier to gain access to drive pin bolt on passenger side of carrier. remove bolt 5/16 head pin will slide out . NOW DO NOT ROTATE ANYTHING. on the side the axle seal is bad tire should be off brake drum off (disc remove caliper and mount) push in on axle c clip should fall out then slide axle out. remove seal with a seal puller and install new one.

May 05, 2014 | 2001 Oldsmobile Bravada

1 Answer

Front passenger side broken axle

Need to replace the drive shaft. Aftermarket parts work fine. The biggest issue is removing inside connection to the half shaft. The clip ring tension is stronger than the boot holding the inboard joint on the drive shaft. To break it loose get a large screw driver and from under the car in front hit the inboard joint hard several times until it over comes the clip ring. Remember... always use jack stands when working under the car.

Aug 12, 2013 | 2005 Acura TL

1 Answer

Inner spline will not disengage from the diff on the drivers side

Hi, its a tough one, but it will come out. try to use a pry bar with a slightly bent tip, you miHT have to turn axle till one of the "bells"is in a reachable place to put the tip between the axle and the trans case. prybar should have its length towards rear of car, maybe add a 3 to four foot pipe over it to add leverage. if that fails, then you have to remove the passenger axle, using a railroad spike or old 1/2 drive extension, you can drive out the driver side axle from the passenger side axle housing.

Aug 10, 2010 | 1992 Dodge Caravan

1 Answer

Car will start but will not move.

is it stick shift or auto box???
for stick shift check the clutch is working and the drive shafts are good
if the half shaft if snaped the prop shaft will turn but the car wont move!
if its an auto box check it is full of oil as well and then check the gear shift is working some times they just fall off,,,,,if the prop shaft is turning and the car wont move the fault is in the rear axle (drive shafts snaped)

Aug 08, 2010 | 1999 Ford Taurus

1 Answer

I have a 97 trans sport and when i drive it it pops real loud, and almost feels like passenger side front end jumps

check your front wheel drive axles/half shafts, see if the rubber boots that cover the bearings are not torn or missing.. sounds like you might need to replace the axle/half shaft on the passengers side

Mar 21, 2010 | 1997 Pontiac Trans Sport

1 Answer

Just replaced hub on passenger side only 80k is this normal also have rear axle seal leaking do i have to remove pumpkin cover to pull axle or will it come out with just removing outer bolts

yes this is normal wear, if you have aftermaket wheels and tires the wear will be quicker do to more stress on the bearing, for the rear seal no u do not have to remove the cover if you jack up the side that has the bad seal you dont even have to drain the fluid. the outer bolts hold the axle in. there is no c clip inside the axle to remove

Sep 27, 2009 | 2005 GMC Sierra 2500HD 4WD

1 Answer

Rear seal and bearing leaking on passenger side.

Basic to get tire and hub off, remove rear diff cover remove bolt, remove clip, pull axle out, then heavy puller to pull bearing and seal. Ck axle for wear

Sep 16, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

(How do I replace rear bearings) chevy sliverado RWD

Check to see if the drum is hotter than normal. If the bearings are bad, you have to lift the truck and remove the axle. Remove the wheel drum until you get to the axle. They to remove the axle, you have to open the rear end Spider gear ***** at the middle. They have a half moon wedge or a clip you have to remove. They you pull out the axle.Replace the bearing grease it and seal it. Then put it back in the reverse order. Sounds simple but it is not that simple. Takes work

Jan 11, 2009 | 1991 Chevrolet C1500

Not finding what you are looking for?
1991 Isuzu Rodeo Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14423 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides