Question about 2003 Nissan 350Z

Open Question

VDC/TCS/ABS/Slip lights all came on.

My front wipers stopped and so did my tach. car starts and runs fine but...

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pal03246
  • 726 Answers

SOURCE: TCS, SLIP and ABS lights on

Check your brake fluid first. If that is low, top it off and recheck. If its ok, than you will need one of the rear ABS sensors. You will need to plug it in and find out which side it is. That's really the only ABS issue that car has. One of the rear ABS sensors fails.

Posted on May 09, 2009

Ad
  • 43 Answers

SOURCE: 350z speedometer stuck at 0 with VDC.TCS/ABS/Slip lights on

check the cable which leads from the tranny to the dash, most of the time the cable or sensor went bad

Posted on Sep 23, 2009

  • 635 Answers

SOURCE: The speedometer on my 350z stopped Working

See if there are codes stored, pull them and start from there.

It may just be a bad vehicle speed sender to the speedometer.

Posted on Apr 01, 2010

  • 237 Answers

SOURCE: Started car to come home after grocery shopping

um yes you do and traction control also.youll nned to go to a shop to see what fault codes are stored.rear wheel speed sensor is a common failure on these.

Posted on Mar 03, 2011

  • 77 Answers

SOURCE: TCS OFF Slip

probably a wheel speed sensor has kicked the bucket, which is why the tcs light came on , have to check your ABS system to see if its functional.

Posted on Sep 12, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TCS OFF Slip


probably a wheel speed sensor has kicked the bucket, which is why the tcs light came on , have to check your ABS system to see if its functional.

Sep 11, 2012 | 2003 Nissan Altima

1 Answer

I have a mitsubishi montero 1999 and the code is p1720


The Engine Control Module (ECM) receives two vehicle speed sensor signals via the Control Area Network (CAN) communication line. One is sent from Vehicle Dynamic Control (VDC) / Traction Control System (TCS) / Anti-Lock Brake System (ABS) control unit, and the other is from Transmission Control Module (TCM). ECMuses these two signals for engine control. Possible Causes: - VDC/TCS/ABS to ECM circuit harness is open or shorted
- TCM to ECM circuit harness is open or shorted
- VDC/TCS/ABS to ECM circuit connectors
- TCM to ECM circuit connectors
- Faulty revolution sensor

Aug 30, 2011 | Mitsubishi Montero Sport Cars & Trucks

1 Answer

Well all the Lights of ABS TCS SLIP started to turn on and i don't why can you tell how can I fix this problem and also tell that TCS was turn off


CANT FIX AT HOME,DEALERSHIP HAS TO FIX.ABS AND TCS SYSTEM HAS TO BE CHECKED WITH SPECIAL DIAGNOSTIC EQUIPMENT.

Sep 20, 2010 | 2006 Nissan Maxima

1 Answer

The speedometer on my 350z stopped Working


See if there are codes stored, pull them and start from there.

It may just be a bad vehicle speed sender to the speedometer.

Apr 01, 2010 | 2004 Nissan 350Z

1 Answer

Dash Gauges out! but still drives


I have the same problem, except for my maxima after it comes to a stop is sluggish starting off. Have you fould out the problem to yours yet? Thanks, Cathy

Oct 01, 2009 | 2006 Nissan Maxima

2 Answers

350z speedometer stuck at 0 with VDC.TCS/ABS/Slip lights on


check the cable which leads from the tranny to the dash, most of the time the cable or sensor went bad

Sep 23, 2009 | 2003 Nissan 350Z

2 Answers

G35, 2004 SLP and vdc dash lights come on.


Haven't seen this very much on 2004's but on 03's There was a service bulletin issued on this. The bulletin directed the technician to perform an inspection of the Brake Control System. Most of the cars I ever saw with this issue had to have the VDC/TCS/ABS control unit/module replaced. The part number for the 03 model sedans is 47851-AM401. if your car is an 04 sedan the part number should begin with the same numbers. Usually there was an internal malfunction in the control unit that caused the computer module that controls and monitors this system to detect a Yaw Rate sensor malfunction which in turn caused the lights to come on and stay on. If your vehicle is a coupe, then the part numbers are a little bit different. I would recommend contacting any Infiniti dealer with your VIN number in hand and ask them if the VDC/TCS/ABS control unit has ever been replaced. Just so you know each and every time an Infiniti has been to the dealer and a repair order was written there is a record of that visit in Infiniti's database, and any dealer can access that information simply by putting in the vin number into their service computer. They can tell you where the car was originally purchased, service history, warranty repair history, any recalls, etc. I would highly suggest doing this, most dealers will even print you a copy of the complete history of the vehicle for a nominal charge. Hope this helps

May 14, 2009 | 2005 Infiniti G35

1 Answer

TCS, SLIP and ABS lights on


Check your brake fluid first. If that is low, top it off and recheck. If its ok, than you will need one of the rear ABS sensors. You will need to plug it in and find out which side it is. That's really the only ABS issue that car has. One of the rear ABS sensors fails.

May 06, 2009 | 2000 Nissan Maxima

1 Answer

Replaced braked pads - now VDC and Slip Lights are on


I would take the car to almost any auto parts store and ask them to check the ODB II computer for codes and to reset the "Check engine light". Get the code that they tell you and it should go a long way to pointing you in the right direction to fixing this problem. It might also be that when you pumped the brakes that you somehow set a code in the computer from the ABS system and now that you have the brakes pumped up and working correctly resetting the Check engine light might fix your problem.

Good luck! Write back with any code you get and I'll see if I can help you figure out what the problem might be.

Jan 06, 2009 | 2004 Infiniti G35 Sport Coupe

1 Answer

Speedometer, check engine, hazara and tcs lights stay on,


Hi,
It ken be many problems,bad contact ,clamping force,tcs/abs unit.
The best you ken do is conect the TECH2 to check def.codes!

Dec 20, 2008 | 2001 Saab 9-3

Not finding what you are looking for?
2003 Nissan 350Z Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...