Question about 1998 Acura TL

Open Question

Why would my crankshaft sensor melt - 1998 Acura TL

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor?


    Pontiac G6 Crankshaft Position Sensors - AutoZone

    www.autozone.com/1/.../pontiac-g6-crankshaft-position-sensor...
    AutoZonePontiac G6 Crankshaft Position Sensors including Crankshaft Position Sensor - Duralast (SU8213), Crankshaft Position Sensor - Duralast (SU9540), Crankshaft ... images for pontiac g6 crankshaft position sensor

Oct 28, 2015 | 2006 Pontiac G6

2 Answers

Eng starts hard,runs good until the rpm is over 2200 then it stumbles my input voltage on the cam sensor is 5volts ,on most cars i've read should have 8volts where


Both crank and cam sensors have a 8 volt reference I have found the wiring melted together where it cross over transmission shorting out the signal. also test your reference voltage at the computer with circuit unplugged at sensor watch meter and wiggle wiring going back to computer this will help find faulty area.

Nov 07, 2013 | 2005 Chrysler Sebring Conv

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

2 Answers

LOOKING FOR SOME IDEAS IF ANYONE CAN HELP WITH ( 96 CHRYSLER SEBRING CRANK SENSOR STUCK IN TRANS. WANT TO REMOVE IT WITHOUT HAVING TO REMOVE TRANSLOOKING FOR SOME IDEAS ANYONE THANKS


Clean it up and spray it with some solvent and let it soak...the o-ring is probably melted..you can also tap it with a rubber mallet to free it up. Of course, the retainer bolt has to be removed.
I hope this helps.

Jul 21, 2011 | 1996 Chrysler Sebring

1 Answer

Jeep just shuts off driving down the road but will restart in 5 minutes. the guages go crazy before this happens.


The first thing i would check is the crankshaft position sensor, I have seen the wires for the sensor melt on the exhuast, i would also check the oxygen sensor harnesses for the same concern. shorted sensor wires will cause powertrain control module to shut down.

Jan 19, 2011 | 1997 Jeep Wrangler

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

1 Answer

Replaced fuel pump spider still no gas at poppits


4.3 L engine crank position sensor is located on passenger side bottom of timing cover. plug should be around the front of the intake manifold.

Oct 09, 2009 | 1995 Chevrolet Blazer

1 Answer

Car starts runs for 10 minutes shuts off . Wait for 10 to 20 minutes car starts again


check the crankshaft position sensor and wire harness. make sure harness is not melted between transmission and block

Jun 12, 2009 | 1993 Chevrolet Corsica

Not finding what you are looking for?
1998 Acura TL Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7727 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...