Question about 2004 Toyota Sequoia

1 Answer

How I remove driver door lock machine.

How I remove the Sequoia 2004 driver door lock.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Toyota Expert
  • 294 Answers

You must remove door panel roll window up and remove, rear window channel by door latch, remove three screws that hold latch assembly pull it to center off door and remove connector, get latch and lock assembly out, remove cover(two small screws) to access screw that hold lock actuator, memorize position off lever, remove and replace.......it is quite a tedious job and tricky good luck.

Posted on Jun 21, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 333 Answers

SOURCE: I need to remove 2004 toyota sequoia tailgate door

Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.

Remove the bolt and the strap/

Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.

Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.

Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.

Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)

The license plate trim panel, should you need to remove it, requires remoaval of the license plate.

Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.

Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)

Posted on Sep 20, 2009

Testimonial: "Very helpful. thanks"

  • 39 Answers

SOURCE: keyless entry on my 2004

do you hear the Beep when you press on the remote to lock/unlock? this is to make sure there is communication with system components....
easiest ting you may do is to reset to system defaults... remove Battery -ve cable for a while... then things should return to normal otherwise you need to check with technician

Posted on Nov 18, 2010

elix0411
  • 3530 Answers

SOURCE: 2005 Toyota Sequoia - Rear hatch door lock is

Welcome to Fixya

Remove the vinyl pull-strap that is located on the rear panel, use a #2 philips to do this. Now start to remove the large inside door panel. This panel has the rear glass inside rubber anti-rattle blade attached to the top of it. (If you were able to open the hatch door from the outside you can remove the inside panel by starting at the bottom of the panel and using a thin blade to lift the panel away from the door and then pop the plastic barbs loose, then lift it up and off of the door sheet-metal.) Starting at one corner, bend out and pull up on the panel where it is hooked over the top of the window opening sheet-metal. It takes a little force to get it started but be persistent, once it is started work towards the other end. Once it's loose at the top you can reach inside and pop loose the plastic barbs that retain the panel and remove it completely.
Thank you for using Fixya!

Posted on Feb 13, 2011

  • 328 Answers

SOURCE: 2004 Toyota Sequoia. Driver door

remote door lock basically unlocks and locks using air pressurized not wires or gears air pressure is directed from a little pump that compresses the air to shoot out the lock probably it is the air line not the pump itself

Posted on Jun 01, 2011

  • 3 Answers

SOURCE: can the 2004 Toyota Sequoia

Give me some more information about this problem. May be i can help.

Posted on Jul 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't program the remote on toyota sequoia?


get a repair manuel at the auto parts store they are cheap.

Jul 31, 2014 | 2004 Toyota Sequoia

1 Answer

2004 Toyota Sequoia. Driver door will not lock or unlock with remote. All other doors lock and unlock with remote, but not the driver door.


remote door lock basically unlocks and locks using air pressurized not wires or gears air pressure is directed from a little pump that compresses the air to shoot out the lock probably it is the air line not the pump itself

Jun 01, 2011 | 2004 Toyota Sequoia

1 Answer

Keyless entry on my 2004 toyota sequoia won't activate any door locks. Door locks will only work when key is in start & run position when pushing button on drivers door panel. Anyone know whats the...


do you hear the Beep when you press on the remote to lock/unlock? this is to make sure there is communication with system components....
easiest ting you may do is to reset to system defaults... remove Battery -ve cable for a while... then things should return to normal otherwise you need to check with technician

Nov 12, 2010 | 2004 Toyota Sequoia

2 Answers

Programming garage door opener 2004 toyota sequoia


GOTO HOMELINK.COM
THEY HAVE THE INSTRUCTIONS FOR ALL OF THESE UNITS.

Jul 26, 2010 | 2004 Toyota Sequoia

1 Answer

04 sequoia will not unlock on rear door... handle was replaced and after 2-3 times will not open.


This is a very common problem with the early model Sequoias. The handle assembly has a poor design.

There is an extended thread about this problem on www.tundrasolutions.com. Go to the Sequoia section. There are several threads that give step by step instructions on disassembling the door and repairing the lock and handle. There are also several suggestions about steps to take to keep the problem from recurring.

Oct 20, 2009 | 2004 Toyota Sequoia

1 Answer

My 2004 Toyota Sequoia rear door will not open - the handle is broken. How do I get into the door, whith it closed, to make the necessary repairs?


Dig out the broken bits of door handle, then on the right side insert a flat head screwdriver diagonally up and fish around for the release lever.
Push up on the screwdriver handle to manipulate the release lever down and your tailgate will open.
Remove the interior panels by unbolting the 10mm bolt behind the strap and pulling off the interior pieces held on by plastic pop fasteners.
Remove the 10mm bolts around the perimeter of the interior cover plate and let it hang by the harness.
Remove the license plate.
Remove the license plate trim panel (multiple push fasteners from behind and a few 10mm around the lock)
Replace the handle.

Sep 13, 2009 | 2004 Toyota Sequoia

1 Answer

Want to fix the passenger side mirrow motor for toyota sequoia 2005


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can remove the bolts holding the mirror onto the door and disconnect the cables from the mirror going into the door

Sep 03, 2009 | 2004 Toyota Sequoia

1 Answer

Drivers rear door wont open from outside child lock on the inside


You will have to pull of the door panel, but most likely cause is the lever from the handle to the latch is disconnected, or possibly the latch itself may be loose/malfunctioning.

Mar 07, 2009 | 2004 Toyota Sequoia

1 Answer

Drivers side rear door lock inoperative


You need to replace the electric solenoid/actuator for the door lock. The door panel pulls off very easily.

Oct 11, 2008 | 2004 Toyota Sequoia

Not finding what you are looking for?
2004 Toyota Sequoia Logo

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...