Question about 1988 Toyota Supra

Open Question

Adjust clutch pedeal on 88 supra

Pedal goes to floor before clutch is desingageed

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 21 Answers

SOURCE: 1987 toyota supra.

hmm. . . . go to tuner shops. . . for sure if they dont have one they can order 1 form japan. . . it maybe an aftermarket clutch but why not. . . they last longer. . . 8)

Posted on Oct 22, 2008

Ad
  • 496 Answers

SOURCE: clutch pedal stays on floor when released

check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.

Posted on Feb 22, 2009

yankstorm02
  • 145 Answers

SOURCE: CLUTCH ADJUSTMENT 1997 TOYOTA COEOLLA

This vehicle has a hydraulic clutch system check the fluid level in the clutch master cylinder it is located on the firewall near the brake master cylinder fill it if its low than check hydraulic system for leaks, possibly slave cylinder, you will have to rebleed the system if part replacement is neccassary

Posted on Apr 11, 2009

  • 8 Answers

SOURCE: toyota supra turbo 1990, manual (7mgte engine) Clutch problem

You ever think about replacing your rubber clutch line with a hard line or just replacing the rubber line

Posted on Aug 18, 2009

iambanshee74
  • 3489 Answers

SOURCE: clutch pedal goes to floor cant get it into gear.

if i remember right, these are hydraulic systems. look under the hood and there should be a seperate resevoir. using brake fluid. look for leaks down where its mounted and inside the truck also, like behind the pedals and under the carpet. there is also the slave cylinder which actuates the clutch fork. pull the boot back and if fluid comes out, replace it. it is a good idea to replace both but do as your pocket book allows in this case. there should be a bleeder on the slave allowing you to bleed it there. good luck. nothing hard about changing these fortunately. happy holidays

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I adjust the clutch on my 1992 Toyota supra?


If its a hydrulic clutch there is no adjustment if its not hydrulic the adjustment should be on the side of the tranny

May 08, 2015 | 1992 Toyota Supra

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up


If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Dec 29, 2012 | Cars & Trucks

1 Answer

How do I adjust play in clutch pedal?


not sure if theses have adjustment on them but if so it will be under the dash on the clutch rod its self

Dec 17, 2012 | 1998 GMC Sierra

1 Answer

The clutch pedal on Suzuki vitara two litre V6 1998 goes to about inch of floor before activation. Clutch does not slip just too much pedal travel. Is it possible to adjust it? ...


prev.gif next.gif Clutch ADJUSTMENTS 1997-98 Models CLUTCH PEDAL HEIGHT The clutch pedal height should not be a periodic adjustment but may be checked after components of the mechanical clutch system have been replaced. The proper clutch pedal height should be 0.2 in. (5mm) above the brake pedal height If adjustment is necessary, loosen the locknut and turn the adjusting bolt until the appropriate height is reached. Once set, keep the bolt from turning and tighten the locknut to secure the adjustment. CLUTCH PEDAL FREE-PLAY The clutch pedal free-play should be checked from time-to-time in order to assure proper clutch operation. The proper clutch free-play should be 0.6-1.1 in. (15-25mm). Fig. 1: Pedal free-play is adjusted at the joint nut (2), while keeping the outer cable nuts (3) tightened around the center cable thread portion 7924hg30.gif
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. If the free-play must be adjusted, turn the joint nut (2) located at the transmission end of the clutch cable in or out, as necessary to achieve the proper play.
  3. Once the correct pedal free-play is obtained, check the free-play on the release arm (c), it should be 0.02-0.06 in. (0.5-1.5mm).
1999-01 Models These vehicles are equipped with a hydraulic clutch system. No adjustment is necessary.

Nov 05, 2010 | 1999 Suzuki Vitara

1 Answer

My 87 Supra Turbo Clutch Pedal is sitting about 2 inches off of the floor board. The clutch itself appears to be working, I just hate that it's on the floor. I've put the clutch under heavy load while in...


I believe you have a hydraulic clutch. You may be low on fluid in the master cylinder for the clutch. If it is low, it takes regular DOT3 brake fluid. After you fill it, you might have to drive it a day or two for it to recover.

Feb 22, 2010 | 1987 Toyota Supra

2 Answers

Toyota supra turbo 1990, manual (7mgte engine) Clutch problem


you need to bleed the clutch system.. have someone pump the clutch pedal three or four times, hold it down and release the bleeder valve( make sure the person holds the pedal down till after you tighten the bleeder valve back down) repeat this four or five times or till the clutch pedal feels like it did before.. good luck keith...

Mar 21, 2009 | 1990 Toyota Supra

1 Answer

Clutch pedal stays on floor when released


check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.

Feb 21, 2009 | 1985 Toyota Celica Supra

2 Answers

I have replaced the Clutch Slave for a 1990 Supra Turbo, and after the next day all the Fluid leaks out from the resevior.I don know wher the fluid goes. what should I do next? Thank You, Frank


Hey Frank.When one cylinder goes the other usually follows because higher pressure needed to operate a new cylinder, sometimes the fluid leaks down the firewall or down your clutch pedal onto the floor, if its your master cylinder that is.You can get a new one or get your old one rehoned and a stainless steel tube inserted and it will last forever as theyre made of aluminium and wear. Either way you'l need to buy a new kit for the inside of it.Be mindful what you order as some models of cars the abs and non abs cylinders are a very slight different diameter. I hope this helps.

Nov 25, 2008 | 1991 Toyota Supra

1 Answer

Clutch adjustment


its the clutch master and slave unit..... u can get them in a pair with the line all ready bled

Oct 29, 2008 | 1984 Ford F 150

3 Answers

Clutch adjustment


sound like your clutch is going it happened to me with my first clutch i have a 88 mustang firstcar still but many problems but yeah not sure.

Jul 05, 2008 | 1988 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...