Question about 1993 Ford F150 SuperCab

Open Question

Where is brake light switch on my 1981 ford truck?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 197 Answers

SOURCE: i have a 2000 ford f 250 1-cyclinder booth brakes

It's at the top of the brake pedel. There is a switch that is held in place by two nuts, it has come loose, make sure that when you tighten it up, it is being pushed up by the pedle, the when you press your brake it completes a circuit. That willl turn your lights off

Posted on Aug 03, 2009

panamajaq
  • 1 Answer

SOURCE: 1981 ford truck alternator schematic

replace an alternator on a 1981 ford f-150

Posted on Aug 05, 2009

  • 19 Answers

SOURCE: rear running lights and brake lights wont work on

i have a 81 f 100 tailights turnsignals work wen i press the brake pedal it blows the fuse ne ideas ??

Posted on Apr 05, 2011

dttech
  • 4803 Answers

SOURCE: can I put a 1981 ford f-150 motor in a 1991 ford f-150 truck

Sounds to me like you opened a can of worms that you are not equipped/qualified to deal with. To begin with, doing an engine change the way you did it is illegal. It is OK to put the newer motor in the older vehicle, but it is against federal law to put the older engine into the newer vehicle. REFERENCE: EPA ENGINE SWAP FACT SHEET

With all that said, if you want to do a swap like that, it is necessary to also swap wiring harnesses and computer modules (among several other components) if you expect it to work.

Posted on Mar 17, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1981 Ford f250 Having a issue with my brake and turn signal lights they blow my fuse every time


One of the most painful troubleshooting tasks is to find where a wire has been rubbed through and is shorted to the chassis. You will need to follow the wires from the tail lights all the way to the switches and find where it's gone short.

May 21, 2015 | Ford F-250 Cars & Trucks

1 Answer

Brake lights dont come on till I step ******* pedal


brake light switch its under the dash look fo the switch that the brake petal rests on when NOT pushing on them thats your problem.

Dec 29, 2012 | 1981 Ford F 150

1 Answer

How to install back up light switch on manual transmission


Yes it is. Unscrew it and screw the new one in and reconnect the plug.

Oct 28, 2012 | 1981 Ford F 100

2 Answers

My 1981 ford f100 brake light comes on when I come to a stop but goes off when I start accelerating?


check the brake fluid level, there is a float in the resavor when you stop all the fluid moves to the frount of the resavor causing the float to drop and turn on the light. fill the master cylinder with DOT 3 brake fluid.

Jan 12, 2012 | 1981 Ford F 100

1 Answer

1981 corvette stingray the brake light has come on and stays on.The oil is ok as is the brake pads are good would it be the booster?


could be a bad brake light switch which is mounted near the brake pedal under the dash try adjusting the plunger which contacts the pedal maybe its on going in far enough otherwise replace the brake light switch

May 16, 2011 | 1981 Chevrolet Corvette

1 Answer

1977 Ford F-100 Lights fliker when light switch is turned on, no brake lights. With switch of blinkers and brake lights work fine. with switch on clicking and instrument lights fliker.


does this vehicle have headlight dimmer swith on the floor.if so make sure that it has a good dround
test this switch
if this is not problem replace light switch

Dec 16, 2010 | 1981 Ford F 100

1 Answer

1982 ford stepside. no brake lights. tried putting a wire to the blinker wires and to the taillight wire from the the brake pedal. nothing works. i have a tail lights,blinkers and reverse but cant get...


Check the brake switch on the back of the brake pedal up behind the dash it should have to wires going to it and will be about 2 1/2 inchs long and threaded. one end will hit the brake pedal on the back side it will look like this >L where the arrow points you will see the switch it will have a quick disconnect on the back of it, and if you take a paper clip and install on the back side intot he wire harness quick disconnet swith look to see if the brake lights are on. If they are on then the switch is bad. to replace it has a half inch lock nut you can back off 1/4 turn then unscrew it out any parts store will carry it. It lists for 14.95 it could be the turn signal switch too. Now this is assuming you checked the fuses also this has two buttons on it and it may be the plug is loose. here is the web page the brake switch is at the bottom and the turn signal switch is about midway. This has a picture with it and price as well. Thanks for using fix-ya http://www.jcwhitney.com/switches/c1643j1s17.jcwx

Apr 23, 2010 | 1981 Ford F 100

1 Answer

Brake lights will not come on signal lights work new master cylinder in a 1966 ford 1/2 ton


there should be a brake switch either in the hydraulic line some where or on the pedal up under the dash . that is most likely what is bad

Sep 22, 2009 | 1981 Ford F 100

2 Answers

Rear running lights and brake lights wont work on my 1981 ford f100 new bulbs and light switch what do i do next


I'd start probing with a test light, or continuity test. Try in & out of your brake switch at pedal, if power there, follow harness outside & down under, and work your way back, or start at plug under, at rear bumper area,or above, near axle probably, & work forward. If you use continuity tester, run a jumper wire from wire going from switch at brake pedal (wire that doesn't have power until pedal pressed.) long enough to reach the back tail lights & see if continuity is there,at back of socket, or in socket, then work forward from there. My guess is that when you find the bad spot in that wire, you'll find the other too.

Apr 05, 2009 | 1981 Ford F 100

Not finding what you are looking for?
1993 Ford F150 SuperCab Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...