Question about Hyundai Santa Fe

Open Question

Why does my santa fe oil level light stay on even after topping up?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: low oil warning light staying on oil level ok

would be best to have oil pressure checked with a mechanical gauge to be sure you have oil pressure.
hopefully you just have a bad oil pressure switch this is located on oil filter adapter rt above filter

Posted on Aug 19, 2008

Ad
  • 21 Answers

SOURCE: transmission filter on 2003 hyundia santa fe

In 2002 they discontinued the external trans filter. So your vehicle could have the external filter. If you look next to the trans dipstick tube, on top of the trans case you will see the filter or you will see just a spot where the filter use to go before they eliminated it. Yes, the filter does llok like a regular engine oil filter. If the trans does not have the external filter ontop then there is no service to the filter to be done, the only recommendation is to bring vehicle into a shop to have the fluid flushed. By the way, make SURE you use the correct Hyundai SP-III trans fluid (not dexron/mercon). This fluid is specific to the Hyundai and can not be purchased from auto parts stores, only the dealership. Failure to use SP-III will cause premature wear to the internal bands and clutches.

Posted on Oct 19, 2008

MrScary66613
  • 1990 Answers

SOURCE: The rear hatch on my 2003 Hyundai Santa Fe won't stay up.

Yes. Your Local Auto Parts Store should Carry these as Direct Replacements. If Not, Sears Carries them.

Posted on Jan 23, 2009

goalie39
  • 469 Answers

SOURCE: ''check engine light'' illuminated, 1004 Hyundai, Santa Fe

If you live in the US, take it to qany Auto Zone store and thy will read the codes off for you, I would suspect any right thinking competitor would do the same, check if you don't have one near by.

Hope this is of some help.
Ed

Posted on Apr 21, 2009

ghost4548
  • 776 Answers

SOURCE: My 2003 Hyundai Santa Fe ABS light is staying on

Here are all the possible problems which can turn on your ABS light.

C1101 Battery voltage over volt: 18V or more ○ ○ BR - 69
C1102 Battery voltage low volt: 9.5V or less ○ ○ BR - 69
C1200 FL wheel sensor: open or short to ground ○ ○ BR - 66
C1201 - Range/Performance: speed jump or damaged exciter ○ ○ BR - 67
C1202 - No signal: air-gap error or wrong excite ○ ○ BR - 68
C1203 FR wheel sensor: open or short to ground ○ ○ BR - 66
C1204 - Range/Performance: speed jump or damaged exciter ○ ○ BR - 67
C1205 - No signal excite: air-gap error or wrong excite ○ ○ BR - 68
C1206 RL wheel sensor: open or short to ground ○ ○ BR - 66
C1207 - Range/Performance: speed jump or damaged exciter ○ ○ BR - 67
C1208 - No signal excite: air-gap error or wrong excite ○ ○ BR - 68
C1209 RR wheel sensor: open or short to ground ○ ○ BR - 66
C1210 - Range/Performance: speed jump or damaged exciter ○ ○ BR - 67
C1211 No signal: air-gap error or wrong excite ○ ○ BR - 68
C1604 ECU hardware: ECU internal or valve failure ○ ○ BR - 70
C2112 Valve relay: valve relay or fuse failure ○ ○ BR - 70
C2402 Motor-Electrical: open or short to battery, motor relay, fuse or motor lock fail ○ ○ BR - 71
C1503 TCS switch failure δ ○
C1605 CAN Hardware failure δ ○ BR - 71
C1610 CAN Bus off failure δ ○ BR - 71
C1611 EMS Time-out failure δ ○ BR - 71
C1612 TCM Time-out failure δ ○ BR - 71
C1613 TCM Un-matching failure δ ○ BR - 71
C2227 Brake disc overheat δ ○
C1274 G-Sensor signal fail (only 4WD) ○ ○ BR - 72
C1275 G-Sensor open or short to ground (only 4WD) ○ ○ BR - 72
You'll need a scanner which is compatible with Hyundai's ABS system to retrieve any DTC's (Diagnostic Trouble Codes) stored in its computer. Any time the ABS light comes on, there's a DTC stored in its computer - that code will tell you where the problem exists. Then you can go from there.

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The dip stick of my 2004 hyundai santa fe is not touching oil


take you car for repair before you destroy the engine. you are ether burning the oil or leaking it.

Jan 26, 2013 | 2005 Hyundai Santa Fe

1 Answer

How to reset oil level warning light 2012 hyundi santa fe


If you have already made sure the oil level is full try disconnecting the negative battery cable wait a minute and re-connect that should clear it. If it doesn't you may have to replace the oil level sensor.

Dec 21, 2012 | Cars & Trucks

1 Answer

Car is leaking oil from top of engine


Hi, You may have problem with either : - top engine rubber seal / gasket broken or - oil / lubricant to much in engine.
You have to replace broken seal immediately. Check again your engine oil level while engine get off. Never fill the oil exceed the max line ( my preference is only fill the oil up to 3/4 level).
Regards, Jay

Apr 19, 2011 | 2004 Hyundai Santa Fe

1 Answer

The brake light on my dashboard has been coming on and staying on in my 2003 Hyundai Santa Fe. What does this mean?


This can mean one of a few things.First, make sure your parking brake is fully released and not even slightly engaged.Next, check your brake fluid level.A low level will trigger a brake light.which this is probably your concern.Finally, your abs(if equipped) could be failing.More than likely it is simple enough as a low fluid problem.Have all four corners checked to make sure all your brakes are up to par and you should be ok.Hope I could help.Rate me accordingly.Thanks!!

Oct 13, 2010 | 2004 Hyundai Santa Fe

1 Answer

Iam wanting to purchase a 2005 santa fe 2.7motor.the vehicle i road tested the oil light stays on


either low oil pressure or oil pressure switch faulty.Get it tested before purchasing as low oil pressure would have caused some wear and tear in the engine.If just a faulty switch then should'nt be a big deal.Get a compression test done also.

Sep 15, 2010 | 2005 Hyundai Santa Fe

1 Answer

My husband was driving my 1003 Hyundai Santa Fe. He stopped the engine to get gas and when he went to start it up, the oil light came on the car was making a terrible knocking noise


have you had oil changed recently? if so look to see if oil pan plug is in tact. if so, check oil on dipstick. the problem is the car has no oil pressure. if the oil level is good the oil pump is bad. good luck!!

Jan 09, 2010 | 2003 Hyundai Santa Fe

2 Answers

Check engine light came on 2001 hyundai santa fe


check oil level and condition, coolant level, as well the pressure in both systems

Nov 06, 2009 | 2001 Hyundai Santa Fe

2 Answers

HOW TO CHANGE OIL ON A 2002 HYUNDAI SANTA FE. IM 19 YRS OLD AND WOULD LIKE TO HELP MY GIRLFRIEND AND CHANGE IT FOR HER. A DETAILED DRAWING POINTING OUT THE OIL CAP AND THE DRAINAGE AND FILTER FROM...


Lift your Hyundai Santa Fe using a jack and then place the car on jack stands. If you don't have jack stands, drive the car onto a set of wheel ramps.
Pop the hood and remove the dipstick and oil filler cap. The dipstick is near the front engine compartment with the oil filler nearby.
Gather an oil drip pan, a 17-mm wrench, oil filter wrench, cleaning cloths and a new oil filter. Slide under your Santa Fe.

Change the Oil
  • Locate the oil filter and oil drain plug underneath the car. The drain plug is on the bottom of the oil pan, and the filter is to the side of the oil pan.
  • Remove the oil drain plug using the 17mm wrench. Pull the plug out quickly and let the oil drain for 10 to 15 minutes. Check the gaskets and threads for damage. Replace these components, if necessary.
  • Take off the oil filter using an oil filter wrench. Dump the old oil into the oil drip pan and put on the new oil filter. Tighten the oil filter by hand, and then replace the oil drain plug using the wrench. Clean off the excess oil.
  • Go under the hood and add oil. Turn on the engine and check the oil pressure gauge to make sure it rises. Let your Santa Fe run for a minute.
  • Lower your Hyundai Santa Fe and turn off the engine. Take an oil reading on the dipstick. If the oil level isn't at full, add a bit more oil.
Thanks
Kinldy rate the answer
Smith

Jul 08, 2009 | 2002 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...