Question about 2007 Bentley Continental GT Coupe

Open Question

I have a bentley continental gt 2007 has p0300 and bank 1 misfires

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: manual trunk release

There are 2 ways to do this. Remove the right rear seat cushion, and seatback. You will find a lever, that is the manual release for the trunk. If this is broken, use a large suction cup, and remove the taillights. This will provide access to the main battery, and start battery. Using an AGM approved charger, charge the main battery(Left-side-AGM) and start battery (Right-side-regular)

Posted on Feb 21, 2009

  • 1071 Answers

SOURCE: How do you reset the keyless entry after the

it has to go to the dealer they have to use a scan tool online to program key fobs

Posted on Aug 18, 2009

  • 2 Answers

SOURCE: 2006 bentley continental w/dead battery. How can

Normally if you use the key and turn it to the left and then to the right the car will start on the resident battery and all will be well. Do not use the start button. If all lelse fails then put a battery charger into the two cigar light sockets for 1 hiur at max 10 amp with ignition turned of and with wires trapped in closed door to switch all coutesy lights off and then there will be enough for the trunk lock to energise. If it is later spec there will be a handle in the trunk accessible thru the centre arm rest by an arangutang!""

Posted on Jan 06, 2011

  • 869 Answers

SOURCE: bentley continental gt battery does not hold full

u might need to change the battery on ur bentley. how old is the car and the bentley ?

Posted on Feb 02, 2011

  • 1 Answer

SOURCE: 2007 Bentley Continental. Dead Battery.

I tried all above on my Bentley continental GT 2003 and it did not work for me. I ended up removing the tail light by taking out 3 screws throught the frank and then jump starting the batteries.

Posted on May 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the runing temperature of the engine on the bentley 2007 gt continental


If you can afford one of these you can afford a call to the dealer you cheapskate.

Nov 01, 2015 | 2007 Bentley Continental GT Coupe

1 Answer

2004 bentley continental gt bonnet releace wont open


You've got a Bentley Continental and you are looking for an answer here? You cheapskate. Call a dealer. My suggestion, is the battery low.

Nov 18, 2014 | 2004 Bentley Continental GT

2 Answers

2007 Bentley Continental. Dead Battery. How do I open the trunk to get at the battery?


Place the negative lead of a set of jumper cables to the frame and the positive to the battery side of the starter solinoid. Then open the trunk. Do not attempt starting it this way.

Feb 22, 2011 | 2003 Bentley Continental GT

2 Answers

I have a Bentley GTC 2007 and the LED strip light is only half working any information on this would be good.


Some leds out in a power strip usually mean those leds are blown. You will probably have to replace the entire strip.

Jan 20, 2011 | 2007 Bentley Continental GT Coupe

3 Answers

Can someone please tell me which battery do I trickle charge on my 2007 Bentley Continental Thanks Stephen


Both Batteries should be removed/disconnected and charged until they read 12.65 vdc with a DVOM.

Dec 19, 2010 | 2007 Bentley Continental GT Coupe

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

3 Answers

2003 Ford Ranger 4x4 extended cab- diagnostics checked and got these codes- P0171, P0174, P0300, P0316. Can you tell me what they mean?


P0171------ system too lean bank#1
Po174------ system too lean bank#2
For these 2 codes, try cleaning the maf sensor (mass air flow), that is mounted in the big black hose that goes from the air filter housing to the throttle plate, if it is dirty, that will cause those 02 sensors to send a signal to the computor to lean the air fuel mixture. If cleaning it doesn't work, the sensors will probably need changing.
P0300---- Random/multiple cylinder misfire
P0316---- Cylinder misfire at start up---- first 100 revolutions.
On those 2 codes, you have to do some testing to find out why there is a misfire.
Possible causes:
dirty/malfunctioning injectors
weak coil pack
fowling spark plugs/wires
Low fuel pressure

May 11, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Where to purchase sevice items for bentley gt coupe


local parts shop, and use the cheapest oil from the supermarket ,just change it every 5000miles no need to change oil filter this often just every third oil change

Feb 19, 2009 | 2007 Bentley Continental GT Coupe

3 Answers

Unintended acceleration


You will need to have a test run of the electronic engine controls, if nothing shows test the Throttle Position sensor, closed throttle voltage should be around 1-1.25 volts, while the meter is hooked up and the key on tap on the sensor the volt reading should remain steady, open and close the throttle repeated times, it still should return to 1-1.25 volts closed throttle blade.

Nov 08, 2008 | 2005 Bentley Continental

Not finding what you are looking for?
2007 Bentley Continental GT Coupe Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bentley Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Are you a Bentley Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...