Question about 2008 Hyundai H100 2.6iD

1 Answer

Why my engine stop at 90 km/h and hard to start when warm

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 3,679 Answers

Have the OBD codes read as this will pinpoint the sensor/switch that is causing the problem as there are quite a few things that could do this , having codes read will save you time and money let me know how you get on

Posted on May 09, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Ford Mustang GT, CAR STARTS UP FINE WHEN COLD. Hard to start when warm No Check Engine lights come on.


Think about how the vehicle is acting. Starts fine when cold, hard to start when warm. In these computer operated systems, the computer runs everything. Starts fine when cold: the computer has the engine in cold start mode putting more fuel in till it warms up. Temperature sending unit in the manifold sends a message to the computer telling it to stop the cold start mode and it stops dumping excess fuel into the cylinders and it runs fine. IF, mind you, IF the temperature sending unit is faulty, it's not telling the computer to stop the cold start mode and is flooding the engine with fuel cause it's sill in cold start mode. This is my take away on your situation and the temp sending unit is something to check to be sure it's functional. Check it out. I hope this WAS the answer to your problem my friend. It's typical. Luck to'ya Bro.

Jun 06, 2017 | Ford Cars & Trucks

Tip

How to use your car, so that it can last longer.


Drive gently and avoid high speeds.<br /><br />Your vehicle does not need an elaborate break-in. But following a few simple tips for the first 1,000 km (600 miles) can add to the future economy and long life of our vehicle.<br /><br />Avoid full throttle acceleration when starting and driving.<br /><br />Avoid racing the engine.<br /><br />Try to avoid hard stops during the first 300 km (200 miles).<br /><br />Do not drive slowly with the manual transmission in a high gear<br /><br />Do not drive for a long time at any single speed, either fast or slow.<br /><br />Do now tow a trailer during the first 800 km (500 miles).<br /><br />Good luck.<br />

on Feb 14, 2011 | Toyota Pickup Cars & Trucks

1 Answer

My truck is 1992 toyota 22re engine , couple weeks ago it started to choke around 80 or 90 km. and couple days ago it stopped working around 30 or 40 km. it starts ok but when i drive it kinda choke...


I can't tell you anything specific but black smoke indicates incomplete burning such as not getting enough air or too much fuel. A quick check of the air filter wouldn't hurt but it's probably something else.

Mar 02, 2013 | 1992 Toyota Pickup

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

1 Answer

I have a 1994 Subaru Legacy and It has started making a "knocking sound". Cked the oil, it was OK


knocks when cold ( Start ), then sort of diminish or disappears when warming up ???

Knocking goes faster when accelerating when cold ???

If Yes, then Piston knocking on the wall of the cylinder . The sound disappears as the engine is getting warmer it dilates and the gap gets smaller.

If this just started,

1. Put quality oil & filter ( Mobile Full Synthetic Oil & Mobile Oil Filter or Purolator )

2. Do not put cleaning agents mixed with oil.

3. Personaly i've put "Restore" Engine Restorer & Lubricant in cars with more then 200 000 km and the results are amazing. But only "Restore". My Volvo is at close to 300 000 km, and it runs great. It's not a cleaning agent.

By experience if the knocking just started you can put an easy extra 100 000 km on the engine before a rebuilt. Quality Oil & let the engine warm up ( 3 mins ).


Nov 02, 2009 | 1997 Subaru Legacy

1 Answer

1994 Nissan Altima Stalls intermittedly at startup


tell your mechanic to look up Service Bulletin #96-032 this could fix your problems

Oct 05, 2009 | 1994 Nissan Altima

1 Answer

I have a Peugot Partner 1.4 . I was driving


you have a stripped and or binding speedometer cable or gear :)

Jun 22, 2009 | 2005 Peugeot 405

1 Answer

'90 Eagle Talon- Won't start!


you got fuel and spark, check the third to the equation, air... maybe you have an obstruction, also if you have a compression guage check the compression. good luck ill check back.

May 02, 2009 | 1990 Eagle Talon

1 Answer

Engine stops running after warming up.


you have a failing crankshaft position sensor

Apr 13, 2009 | 1990 Oldsmobile Cutlass Supreme Conv

Not finding what you are looking for?
2008 Hyundai H100 2.6iD Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...