Question about 2005 Chrysler Pacifica AWD

1 Answer

Where is the o2 sensor part number 13937 located at on 2005 chrysler pacifica

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 752 Answers

Hi John, I'm glad to help. John I'll have to answer this 2 ways because I'm not clear on what your asking. (1) The 02 Sensor's always have the part #'s on them if they haven't worn off to the point you can't read them. (2) If your asking where that 02 sensor is located on the car. Here's what you need to do to find out. Go back where you bought the new 02 sensor. Give them the part number and they can look it up and tell you where it is located and where to install it. Hope this helps and have an awesome day John!

Posted on Jun 11, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: 2006 Chrysler Pacifica Auotmatic Liftgate

Yes new gas shocks on the lift gate will fix your problem. I had the same problem on my 2005 Pacifica and when it hit my head- I came up with the solution.

Good Luck,
Ray

Posted on May 11, 2009

turo1000
  • 18 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Posted on May 18, 2009

  • 34 Answers

SOURCE: 2005 chrysler pacifica code 0420

Code P0420 is a catalist ineficiency code. It can be caused by a minor exhaust leak. Based on what youve already replaced. Inspect the entire system while its running to find any leaks.

Posted on Nov 24, 2009

  • 1 Answer

SOURCE: location of pcm on 2005 pacifica?

I have a 2004 Pacifica and mine is on the drivers side front, underneath between the bumper and the wheel splash guard. You will need to remove the splash guard ti access the PCM. Not very hard at all. Replacement time for a handy DIYer: about 1/2 hour. Good luck!!

Posted on Jun 05, 2010

jturcotte
  • 8215 Answers

SOURCE: where can I find a

3.5L engine?

8fe7d61.gifd8f14c0.gifac805da.gif

Posted on Oct 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change a o2 sensor in my 2005 Chrysler Pacifica


if you can see where it is. Heat around o2 sensor with hand soldering torch, Remove o2 sensor with special o2 sensor socket.
Put car on stands when you jack up the car or use car ramps and block the rear wheels to prevent the car from moving.

Mar 27, 2015 | 2005 Chrysler Pacifica

2 Answers

P0420 p0522 chrysler pacifica CODES


thje po420 need to monitor o2 sensors to verify if you have a bad sensor or bad catalitic converter
the po522 oil presure sending unit

Oct 15, 2014 | 2005 Chrysler Pacifica

1 Answer

O2 sensor


Raise car, take off negative battery cable and slide under the drivers side and unplug wires then unscrew the two o2 sensors one in front and one behind the converter. Put anti seize on threads, it comes with them. then put them back in snug tight. Put cable back on

Nov 17, 2013 | 2005 Chrysler Pacifica

1 Answer

Where is Oxygen Sensor located in a 2005 Chrysler Pacifica?


Under the car in front and behind the catalytic converter. There are two

Sep 20, 2011 | 2005 Chrysler Pacifica

2 Answers

I have a 2004 Chrysler Pacifica


136266353that would be your HO2 sensor. It's located in the left hand exhaust manifold closer to the top of the engine. It usually takes a special socket to remove one. If you have any doubt, take it to a shop and have them replace it for you. This sensor effects fuel and driveability, don't go to long without fixing it as it may cause damage to your catalytic convertors.

May 31, 2010 | 2004 Chrysler Pacifica

1 Answer

Wher are the oxygen sensors locted on a 2005 chrysler paciffica?


they are located on the exhaust system some cars have two and some have four o2 sensors. they should be located any were from the exhaust manifold to the catalatic convertor and you should have at least one after the convertor

Jan 15, 2010 | 2005 Chrysler Pacifica

1 Answer

Chrysler Pacifica ABS on


Not long at all, there located in each wheel. Worst case is about an hour per sensor...

Nov 05, 2009 | 2005 Chrysler Pacifica

Not finding what you are looking for?
2005 Chrysler Pacifica AWD Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...