Question about 1995 Dodge Avenger

1 Answer

How to repllace valve cover gasket on a 1995 dodge avenger 2.5L v6?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 3,679 Answers

Remove the intake plenum to gain access to the plugs ,remove plugs and leads ,note what lead went to what cylinder for refitting, four bolts per rocker cover the gasket will almost certainly be burnt into the groove on the rocker cover so be careful when digging this out that you dont damage the edge/rim ,on refitting i'd put a bead of silicone gasket around the rocker cover groove to ensure good seal , your best friend in doing this will be PATIENCE , hope you dont know some one of that name !good luck and keep me posted

Posted on May 09, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

leetamara
  • 702 Answers

SOURCE: 89 Dodge Raider 3.0 Labor hours to replace Valve cover Gaskets and seals

.5 for the 4 cyl. and its 3.6 for the 6 cyl. engine. This is according to the Chilton Labor Guide.

Posted on Nov 10, 2008

  • 1596 Answers

SOURCE: possible bad ignition coil and valve cover gasket

No start on 97 dodge intrepid. I Know that Coil pack is Below Valve cover and Have repaired Numerous Ignition coils due to there becoming Oil soaked , the oil will gather dust dirt and thus Insulating ( Retaining Heat) i and this Causes them to Over heat and Fail , in short Burning them out. I say this Because of your Mention of it as a symptom. you must first Determine if it is getting spark ,have someone Crank Engine over While you are Holding the Spark plug wire 1/4 inch away from coil tower (TERMINAL) do this to all 6 if no spark at any of them ,that coil could be bad (Most Likley), If all Have NO SPARK then it is One of the fallowing,,

  1. Cam Sensor
  2. Crank Sensor
  3. Ignition control module
If Control module is wet with Oil most likely needs replaced some Parts stores can test coil and Modules.

NOW if you have Spark on All 6 Cylinders Check for fuel delivery, Do this at the shrader Valve on the fuel rail,(LOOKS LIKE AIR FILL VALVE ON WHEELS) Simply remove cap turn key on for 5 seconds then turn it OFF Depress the Stem at shrader valve If you get a Good SPRAY of FUEL upon doing this 3-4 times then you have Fuel Pressure !!!!WARNING !!! Test Equipment is Recommended for all Procedures but their certain steps to take if you don't have a DIGITAL VOLT METER or Fuel Pressure tester. I Hope this helps you with your Diagnosis od the problem. Have A Good Day

Posted on Jan 13, 2009

  • 47 Answers

SOURCE: how do i replace the valve cover gasket on 99 dodge avenger?

You may want to look at Auto Zone web site, the vehicle repair guide.
It described how to change the valve cover.
You could also go to the public library and check out the Auto repair section and photo copy the section with valve cover.
Also advance auto web site also have a vehicle repair guide section.
You can check it out and decide if this something you want to get involve in. It describe ever step that is involve.

Posted on Mar 10, 2009

  • 740 Answers

SOURCE: 2000 DODGE STRATUS 2.5 V6

There may be a ground wire that you forgot to put back or a power wire that give power to the coils. Re-check all electrical wiring and make sure they are all connected. Good luck and thanks for using FIX YA

Posted on Mar 21, 2009

  • 1 Answer

SOURCE: replace valve cover gasket

I have the same problem on a 2003 Town & Country. The cover for the front 3 cylinders is quite straight forward, but in order to do the rear cylinders I believe you are going to have to remove the cowling below the windshield. You will need a gear puller to remover the windshield wipers first, then remove the cowling. Than should give you more room to work. It's still not going to be easy, but it sure beats paying hundreds of $$$$ in labor charges.

Posted on May 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2008 Dodge Avenger R/T where is my egr value? How hard is it to replace?


You don't say what engine yours has ! This 06 dodge magnum with 2.7 mite be similar .If not you mite find another video 2006 Dodge Magnum 2 7L V6 EGR Valve Replacement

Oct 01, 2016 | 2008 Dodge Avenger

2 Answers

How many belts do a 1995 dodge avenger have


If it is 2.5 or 3.0, there is three. 2 serp belts and 1 timing belt

Feb 15, 2011 | 1995 Dodge Avenger

1 Answer

Replacing valve cover gaskets on 1995 Dodge Caravan


id put a little sealer on just to hold it in place i change mine and its been a year no leak

Sep 26, 2009 | 1995 Dodge Caravan

1 Answer

Tranny slips and wont go into gear


I'm sure you ck'd the fluid level, so that would leave a restricted filter, faulty front pump, a valve body gasket leaking, etc. Drop the pan, the story is in the sediment and on the filter.

Jul 29, 2009 | 1995 Dodge Avenger

1 Answer

Need to replace


In order to replace it you would have to take off  your inkate manifold. Then the tire gaurd to get to the bolts for the alternator and when you lossen the alternator you have to play around with it to get it through the top. 
I would also reccomend grabbing a haynes manual for your avenger. You can find them on ebay pretty cheap, and you can usually pick them up at your local auto parts stores. 

May 24, 2009 | 1995 Dodge Avenger

1 Answer

How to change valve cover gaskets on 92 Dodge Minivan 3 Liter V6 Engine. Is it difficult to do in own garage.???


No, not at all!

Take your time....take pics of it BEFORE you remove the next piece.

No special tools required.

Mar 31, 2009 | 1992 Dodge Caravan

1 Answer

Leaking valve cover gaskets


The problem is over tightening.

If you over tighten your fastners you will sqeeze your gaskets too much and they WILL leak.

You can use black silicon sealant LIGHTLY but you don't really need it. If you have the V6...the torque on them nuts are only 80 in lbs each

Mar 29, 2009 | 1991 Dodge Dakota

1 Answer

1995 Dodge Avenger 2.0 engine bogging


i think your on the right path with wires and plugs. also has your timing belt ever been replaced. if is a little lose it could be retarding the valve timing.

Mar 15, 2009 | 1995 Dodge Avenger

1 Answer

How do i replace the valve cover gasket on 99 dodge avenger?


You may want to look at Auto Zone web site, the vehicle repair guide.
It described how to change the valve cover.
You could also go to the public library and check out the Auto repair section and photo copy the section with valve cover.
Also advance auto web site also have a vehicle repair guide section.
You can check it out and decide if this something you want to get involve in. It describe ever step that is involve.

Mar 10, 2009 | 1995 Dodge Avenger

Not finding what you are looking for?
1995 Dodge Avenger Logo

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...