Question about 1999 Chevrolet Corvette

1 Answer

How to remove a blend actuator in a 1999 corvette

What do i need to do to remove it myself

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Chevrolet Master
  • 808 Answers

The blend door actuator is located on drivers of car above the gas pedal and held down with 2 or 3 5.5 mm screws good luck in a tight area.

Posted on May 09, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4369 Answers

SOURCE: remove ash tray from chevy

usually a tab to press to release ash tray, or tabs to press on the sides of hte ash tray.

Posted on Sep 04, 2010

emissionwiz
  • 76846 Answers

SOURCE: 2004 monte carlo heater door actuator replacement

This job requires the complete removal of the dash from the car and dis-assembly of the duct work to replace the blend door. You must have a factory manual to have any chance of not messing this up completely.

Posted on Aug 26, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

1 Answer

How do i get to the drivers side HVAC blend actuator


You have to just about pull the whole dash out !


Removal Procedure




  1. Remove the front floor kick-up panel. Refer to Kick-Up Panel Replacement - Front Floor in Interior Trim.


  2. Remove the cover from the I/P electrical center.


  3. Remove the HVAC CON (HVAC controls) MiniFuse?® #27 from the I/P electrical center.


  4. Remove the I/P upper trim pad. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gauges and Console.


  5. Remove the instrument panel cluster (IPC) to steering column bracket retaining screws.


  6. Reposition the IPC to better access the LH temperature valve electric actuator.


Is yours manual or automatic HVAC system ? if you haven't done this before I suggest you take it to someone who has !

Jun 02, 2015 | 1999 Chevrolet Corvette

1 Answer

Could someone please tell me where the blend door actuator is on a 1999 Olds cutlass and what I have to do to remove it? Thanks


http://www.bing.com/images/search?q=blend+door+actuator+is+on+a+1999+Olds+cutlass&FORM=HDRSC2

May 18, 2015 | Cars & Trucks

1 Answer

How to replace the driver side blend door actuator in a 1999 cadillac deville


Air Mix Actuator Replacement - Driver





Removal Procedure





  1. Remove the right sound insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gauges and Console.


  2. Remove the instrument panel compartment. Refer to Instrument Panel Storage Compartment Replacement in Instrument Panel, Gauges and Console.


  3. Unsnap the rod from the plastic retainer on the actuator arm.

  4. Remove the two screws from the actuator (2).


  5. Disconnect the electrical connector (1).


  6. Remove the actuator (2).


  7. Inspect the air mix door for free travel.

Jul 06, 2012 | 1999 Cadillac DeVille

1 Answer

Afternnon, just wondering about the best way to locate the blend doors in the hvac box without ripping out the dash on my 2000 jeep grand cherokee. Thanks in advance. Duane


y9ou can gain access to the driver side blend door actuator by removing the glove box. The actuator will be in the left corner of the glove box opening. If you remove the actuator you will be able to turn the pin. If you can turn it 360 degrees the blend door is broke.

If your lucky its only the drivers side. If you get the repair kit from chrysler it will come with instructions with pictures on how to replace the blend door without pulling the HVAC unit/Dash. If the passenger side is broken the HVAC unit will need to be removed.

Heater treater (google them) also have a metal blend door replacement and instructions online on how to replace them without pulling the HVAC housing.

Nov 28, 2010 | 1999 Jeep Grand Cherokee

1 Answer

2001 Ford Windstar, front and back heaters, back works fine front blows cold air


check the front blend door actuator if it is working.The actuator may be working but the blend door is broken stuck.remove the dash console panel [ac heater panel and radio] you can see the door actuator.remove the 3 screws and pullout the actuator using flat screwdriver try to rotate the door

Jan 08, 2010 | 1999 Ford Windstar

1 Answer

What do I have to remove to access blend door actuator


very lenghty process. too long to describe here....go to Bonneville Forums read the text and follow linked there at the bottom....very good and detailed....I'm doing that right now,,,,it is a bugger,

Dec 10, 2009 | 1999 Pontiac Bonneville

2 Answers

1999 Silverado - cannot get the temperature to switch from cool air to warm air when turning the knob to heat.


The temp blend door, or blend door actuator may be faulty. You can check this by watching the movement of the blend door actuator while you turn the temp selector knob. If the actuator is working, then it may be the blend door, or blend door lever broken. If these are ok then the control head may be faulty.

Oct 18, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Fuel door does not stay closed on a 2005 corvette I have the exact same problem. Dealer says its an Actuator. they want $225.-250. to replace it. Can I get the part cheaper and do it myself? Thanks!


IT is the actuator, it comes with the cable, you are suppose to remove the inner fender well to do this job, you can sqeeze your hand, but it is not easy.

May 04, 2009 | 2005 Chevrolet Corvette

1 Answer

Wine


this is correct, there could be two possibilities, one is the blend door actuator which is mounted on the heater plenum and second is the actual blend door could be broken or binding, to check the actuator you need to remove the radio and if you look down at the heater plenum you will see (normally white) electric actuator. remove the actuator by removine the 3 8mm bolts, once it is out plug it back in and check the operation by changing the temperature from hot to cold, if it does move than the problem is in the plenum and will require replacement

Oct 04, 2008 | 1999 Ford Windstar

Not finding what you are looking for?
1999 Chevrolet Corvette Logo

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...