Question about Cars & Trucks

1 Answer

I need the rod bearing torque specs and sequence on a 1996 Dodge grand caravan 3.3Lv6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,679 Answers

Follow this link ,i'm sure your vehicle will be here just click on torque tables
http://www.speedwayautoparts.com/index35.htm

Posted on May 09, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ewashmidas
  • 362 Answers

SOURCE: torque specs for the main bearings, connecting rods and heads

Here you go...

Connection Rod Nuts: 37-38 Ft Lbs.
Main Bearing Caps: 55-61 Ft Lbs.
And Head Bolts...

1st - step; - 80 ft./lbs. 2nd - step, loosen all bolts; 3rd - step; - 80 ft./lbs.
69de06e.png

Posted on Jan 24, 2009

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

c17hydro
  • 2984 Answers

SOURCE: What is the sequence for the bolts on oil pan, for

For the 2.8L there is no sequence. Torque for the bolts are 105 in.lbs.

For the 3.0L torque is 50 in.lbs. in sequence:




40be0ec.gif

30fedd0.gif
For the 3.3L and the 3.8L, no sequence but torque each bolt to 105 in.lbs.

Please don't forget to rate!

Posted on Jul 12, 2009

  • 149 Answers

SOURCE: I need the torque specs for the connecting rod cap

Step #1 40lbs PLUS Step#2 1/4 turn 90 degrees.....this is for 3.3 & 3.8

Posted on Jan 19, 2010

BCAS1298
  • 3092 Answers

SOURCE: TORQUE SPECS 2.2 GM 1996 S 10 PICKUP

Rod bearing torque at 38 ft.lbs.5b9c564.gif

Posted on Jun 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the tighteing sequence on a 97 5.2 dodge ram 1500 connecting rods


First thing to do is use plasti guage in the inside of each bearing cup, tighten to spec and then remove it, measure the expansion of the plasti gauge to see if the clearance is within specs. Apply assembly grease and reassemble if ok. Two bolts on a bearing cap don't have a sequence to speak of. You finger tighten them both to the same point. Get a torque wrench and set it to half of the final value, tighten one, tighten the other, reset the wrench to final value, tighten one, tighten the other.

Jan 27, 2017 | Dodge Cars & Trucks

1 Answer

2011 grand caravan rod cap bearring torque specs?


Why are you attempting this level of repair without a manual? You are going to need all sorts of info to do a good job. Why skimp on a manual when a false move could cost you all your work.

Nov 15, 2014 | 2011 Dodge Grand Caravan

1 Answer

Engine Torque Specs for 1996 850 glt volvo rod bearings


15 ft lbs then angle torque 90 degrees

May 13, 2014 | 1996 Volvo 850

1 Answer

Lookin for head torque specs and sequence


Torque sequence ----------- ' 9 7 3 1 5 ' ' 8 4 2 6 ' ----------- Step 1: torque in sequence to 45 Ft/Lbs Step 2: torque in sequence to 65 Ft/Lbs Step 3: torque in sequence to 65 Ft/Lbs again plus 1/4 turn Step 4: Torque small bolt in rear of head to 25 Ft/Lb Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
3.3L

Feb 07, 2011 | 1996 Dodge Grand Caravan

1 Answer

2006 grand caravan sxt 3.8 liter outer tie rod torque specs needed please.


Hello billmarks: My name is Roger and I will help you. The torque specs for the tie rod lock nut and the tie rod spindle nut is 55 foot pounds. Should you need further help please just ask.Please rate the answer. Thank You for using Fix Ya. Roger

Sep 08, 2010 | 2006 Dodge Grand Caravan

1 Answer

I need the torque specs for the connecting rod cap bolts for a 2005 dodge grand caravan


Step #1 40lbs PLUS Step#2 1/4 turn 90 degrees.....this is for 3.3 & 3.8

Nov 07, 2009 | 2005 Dodge Grand Caravan

1 Answer

What is the sequence for the bolts on oil pan, for 2000 dodge grand caravan? What is the torque for bolts for oil pan for 2000 dodge grand caravan?


For the 2.8L there is no sequence. Torque for the bolts are 105 in.lbs.

For the 3.0L torque is 50 in.lbs. in sequence:




40be0ec.gif

30fedd0.gif
For the 3.3L and the 3.8L, no sequence but torque each bolt to 105 in.lbs.

Please don't forget to rate!

Jul 12, 2009 | 2005 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...