Question about 1993 GMC Sierra

1 Answer

How to replace Ignition Module of 1993 GMC Sierra

Posted by on

Ad

1 Answer

Assuming it is in the distributor,
you remove two screws & unplug the wire
connector

Posted on May 08, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1993 GMC sierra 1500 extended cab 4.3 v6 TBI and I'm hearing stories about this Accel Remote Mount Super Coil burning out Ignition Control Modules


I don't know about your particular application, but I do know that manufacturers are not using heavy enough wire for many things on a vehicle. So if the coils are bigger (higher output voltage) then they probably would draw more power and more load on control modules. I don't know any reason why stock would not be enough spark, these are a lot more powerful already than ignition systems were 40+ years ago. So in my opinion, no I wouldn't do it.

Nov 05, 2016 | 1993 GMC Sierra

1 Answer

1993 Sierra removal of ignition module


The ignition module is under the distributor cap. Mark the spark plug wires location then remove the cap. Remove the 2 screws and connectors.

May 08, 2014 | 1999 GMC Sierra 3500

2 Answers

I have a 93 sierra,4.3 liter, put new plugs,cap,rotor and the ignition relay is good. it gets gas cause i smell it and it turns but will not start.what could be the reason it will not start? its a new


check the fuel line pressure on the injector rail ,here you will find a valve that looks like a tyre valve and take the cap off and connect a pressure gauge to this and see what you get should be around 55lbs

Mar 30, 2012 | 1993 GMC Sierra

1 Answer

I have a 2000 gmc sierra 4.3L that has had the ignition module fail REPEATEDLY over the last 6 months. Auto shop has replaced it ever time, which gets the truck to run again, but only to have it fail again...


Try using heat sink grease between the metal base of the ignition module and the mounting position, from the sounds of it the circuitry is overheating and failing. I noticed that this particular module is very hot while the truck is running with my own Sierra

Aug 16, 2011 | 1994 GMC Sierra

1 Answer

Were is the shift module located at on a 1993 gmc sierra


Shift module? Are you talking about a control for the transmission? The Engine computer controls the transmission. What kind of problem do you have? I can likely help.

Aug 07, 2010 | 1993 GMC Sierra

1 Answer

I have a 1993 gmc sierra. I have been have


no, the ignition cylinder may have to be replaced to start.

Jul 20, 2010 | 1993 GMC Sierra C3500

1 Answer

What are the timing specs on a 1993 GMC Sierra Z71?


theres no advance wire on that engine!!! theres a hash mark on the back of the intake and one on the distrbutor shaft you set the distrib with the has mark and yes!! the ecm! will always reset the timing that is what is does but if it's pinging or knocking then change the ignition module cause the dwell side of it is out of range!

Jan 14, 2010 | 1993 GMC Sierra K1500

1 Answer

Have a 1993 gmc sierra. runs fine most of the time . but will just kill sometimes out of the blue. does not matter if it is warmed up or cold. when it dies will just turn over but not start. replaced spark...


When this truck dies,does it have spark,or fuel pressure?Check it for no spark,if it has no spark,replace the ignition module.These gm year models are bad to go out ,and the distributor pick up coil also.Replace the module first,if this does not help,replace the pick up coil.NOW ON A FUEL RELATED PROBLEMit could be fuel pump,fuel pump relay,or the pick up coil.The pick up coil pulses the injectors,and the spark.I hope this helps,if not let me know.

Sep 20, 2009 | 1993 GMC Sierra

1 Answer

We have no spark from the coil


take the cap off the dist and pull out the ignition module take it to autozone and have it tested also check out the cap and rotor replace it if it been awhile

Aug 17, 2009 | 1993 GMC Sierra K3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...