Question about 1998 Isuzu Rodeo

1 Answer

Webasto sunroof wont close

My webasto starlite vi/vii is stuck in the vent position and won't close I have changed the fuses to no avail

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 194 Answers

Check to see if you can use the manual crank to unstick it then use the power

Posted on May 09, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sunroof does not open. Fuse is ok and the shade operates normally.


Do you know how to do automotive electrical testing ?????? How to read a wiring diagrams ???? http://www.bbbind.com/free_tsb.html .Videos on youtube Ohms Law Tech Tip from L1 with Dave Hobbs Copy of Voltage Drop Essentials TST Motor Age The only way to find the problem , testing !

Sunroof Description and Operation (One Connector System)
Sunroof
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
• Open
• Vent
• Closed
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.

Your best bet , take it to a qualified repair shop or buick dealer .

Feb 10, 2017 | 2010 Buick LaCrosse CXS

1 Answer

2001 cadillac deville sunroof open and want close


Check the RAP fuse in the rear fuse box , this fuse powers the sunroof control module ! Fuse Block - Rear , Left rear of the passenger compartment, under the rear seat .
The sunroof module contains the logic for the opening and the closing of the sunroof. The sunroof motor assembly contains the reversible DC drive motor, the gear train, and the limit switch.
The sunroof module determines the sunroof motor direction based on inputs received from the overhead console sunroof switches. When the ignition switch is in the ON position or when retained accessory power (RAP) is active, voltage is applied to the sunroof module via the RAP relay. For a description and operation of the RAP system, refer to Retained Accessory Power (RAP) Description and Operation in Retained Accessory Power. The sunroof module controls the sunroof motor direction by changing the polarity of the applied voltage. The sunroof module remembers the sunroof position whenever the ignition switch is turned to the OFF position. The limit switch is used as an input to the sunroof module to indicate that the glass is fully closed, or in the comfort stop positions. The limit switch is grounded when the sunroof glass is in the fully closed or comfort stop positions, otherwise it is open.
The SLIDE CLOSE mode is initiated by moving and holding the sunroof slide switch (ROOF) forward. This applies a ground provided from the sunroof limit switch low reference circuit to the sunroof switch close vent signal input of the sunroof module. The sunroof module controls voltage to the control circuits of the sunroof motor. The sunroof motor will run until the limit switch contacts are closed. The closing of the limit switch will apply the sunroof limit switch low reference circuit to the sunroof limit switch soft stop signal circuit to the sunroof module, indicating the flush closed position has been reached. As the sunroof is approaching the close position the sunroof glass will force the wind deflector downward.
You need to have a factory scan tool hooked up an have it checked for DTC'S in the sunroof control module ! a code reader will not do this , a code reader will only check the engine codes for OBD 2 .
Important: The following must be completed before using the symptom tables.
  1. Perform Diagnostic System Check - Power Sunroof in order to verify that all of the following are true:
  2. ?€¢
    No DTCs are set.


    ?€¢
    The control modules can communicate via the serial data link.

  3. Review the system operation in order to familiarize yourself with the system functions. Refer to Sunroof Description and Operation
your better off taking to the dealer !

May 09, 2015 | 2001 Cadillac DeVille

1 Answer

My Pontiac G6 Sunroof is stuck in the vent position.


might try spraying white lithium grease on the slides and open and close few times my g6 did the same thing grease it and open and closed a few times then it work

Feb 28, 2015 | 2006 Pontiac G6 GTP

1 Answer

2001 yukon xl which fuse is the sunroof fuse


In the under hood junction box , fuse CTSY LP 15 amp . Instrument fuse panel PWR WDO CB 25amp .
Sunroof Motor Synchronization
Synchronization will be necessary anytime the sunroof module battery positive voltage circuit is interrupted. The sunroof module will be synchronized when the controller learns the full vent position. The sunroof system will ignore any open request until the system has been synchronized.
To synchronize the sunroof:
  1. Turn ON the ignition, with the engine OFF.
  2. Using the close/tilt up portion of the sunroof switch, operate the sunroof glass until it reaches the full vent position.
  3. Verify that the system operates normally.
Once the sunroof glass reaches the full vent position, the actual position is stored in the memory of the sunroof module. The sunroof module will stop the motor one motor revolution before the defined actual positions
Hope this help ! good luck !

Dec 24, 2014 | 2001 GMC Yukon XL

1 Answer

Stuck sunroof


This is an electrical problem. Check fuses and replace if necessary.

Jul 05, 2013 | Cars & Trucks

1 Answer

2000 olsmobile alero sunroof stuck open


HAVE SAME PROBLEM ON MY ALERO , WOULD CLOSE TO VENT POSITION ALL OTHER FUNCTIONS WORKED FINE. TALKED TO A MECH. FRIEND AND FOUND A WAY TO CLOSE MANUALLY BUT YOU DO HAVE TO DROP FRONT LEFT CORNER OF HEADLINER.
THE MOTOR IS UNDER SUNVISOR AREA AND YOU'LL NEED AN ALLEN(SPELLING)SOCKET TO CLOSE ROOF

Oct 20, 2012 | 2001 Oldsmobile Alero

2 Answers

Need to fix the sunroof of a 2000 Volvo S80 . It


hold the switch down for around 20 seconds and it reset the sun roof /in close position

May 09, 2009 | 2000 Volvo S80

1 Answer

Sunroof wont close


you may have changed the wrong fuse

Apr 30, 2009 | Ford Expedition Cars & Trucks

1 Answer

2002 Oldsmobile Alero Sunroof Stuck in the Vent position


The sunroof continues to open and close normally from front to back, but the vent stays open.

Apr 01, 2009 | 2001 Oldsmobile Alero

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...