Question about Cars & Trucks

1 Answer

My show an tell indicator lights won't work I changed the clocks an still won't work it's not a fuse but the indicators flash an the hazards on the outside do u know what it cud be it's an mg zt

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 194 Answers

Check the turn signal relay

Posted on May 09, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Benimur
  • 6966 Answers

SOURCE: vw golf 1994 indicators

Hi,

Most Golf and Jetta have their relays bunched together with the fuse block. Often, it would be inside the fuse box/compartment located under the facia panel, on the right-hand side, behind a removable cover. On most models, the flasher relay would be labeled 21.

Incidentally, sometime ago, there was a recall on some Golf where Volkswagen dealers will install a new hazard flasher switch/relay kit to remedy a common issue. You may want to try first Volkswagen at 1-800-822-8987.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Jun 07, 2008

j_del
  • 1586 Answers

SOURCE: Flashing Unit for Indicators Replacement

Most likely it's the hazard switch - the relay for the hazards and the turn signals is built into it. When they start to die, you will see erratic behavior with the turn signals and/or hazards, and eventually they'll both fail completely. Replace your hazard switch on the dash and you'll be good to go.

Posted on Aug 31, 2008

  • 1 Answer

SOURCE: HAZARD LIGHTS ON BUT NOT

HI,
I have the same problem - it is the relay switch attached to and behind the hazard warning triangle on the dashboard. Pull it all out (gently and replace (£60 ish). The indicators and hazard lights are on the same relay circuit. This is a well known problem for this car (amongst others - how about the wipers sticking)

Posted on Nov 25, 2008

bunnydawg
  • 5158 Answers

SOURCE: Indicators not flashing on Audi TT

i believe the audi uses two relays for the turn signals and hazzard lights so it would appear the turn relay has failed. it should be located under the dash near the steer column.... seems to me me they have some shielding under the dash so it may be hard to get to.

Posted on May 23, 2009

GasparMacari
  • 166 Answers

SOURCE: Vauxhall/Opel frontera indicators not working

thats a relay thats is not working propperly, must be replaced to fix the problem, just go to your dealiship and ask for a turn indicator relay for your model and ask your part sales man to show you where is located, if not...just follow that click...
have fun

Posted on Aug 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No indicators working or hazard lights how can you tell if a relay fuse is broken


fuses can be checked by a visual inspection ( the wire between the 2 prongs must be intact not broken in the middle) or with a multimeter set to continuity test (ohms setting) if there is a circuit the reading will drop to zero and if not continuity the reading will not change

Jul 23, 2015 | Hyundai Excel Cars & Trucks

1 Answer

The indicator lights are all stuck on. AU Ford station wagon. Removed relay, and all fuses, but still on. Disconnected battery and they turned off. Reconnected battery and they all came back on with no...


The AU ford has two indicator relays , turning lights and hazard lights ,both use the indicator lights ,the hazards flash both front and rear lights , the turning indicator flashes one front and one rear light. I think the fault may be in the hazard circuit.

Feb 25, 2015 | Ford Cars & Trucks

1 Answer

Indicators & hazard lights


it is worht checking the fuses and also keep working the hazard light switch as they are not used that often they tend to get sticky on the con tacts and that will knock out your indicators as well if they start to work after working afer working the haz switck then change the switch

Dec 30, 2013 | Mitsubishi Outlander Cars & Trucks

1 Answer

Hi wonderd if any one can help. i have a ford focus 2002 tddi estate the hazards arnt working but the indicaters are. i've changed the hazard switch for a new one and checked all the fuses in the


Look on the back of the fuse board ,for this you have to drop the fuse board as their are two fuses at the back and i know one is for the central locking ,the other ? Now when the hazard switch is disconnected the indicators shouldnt work but the only thing i can think of is the indicator unit is faulty ,do the hazards light the indicator lights up and they dont flash or is nothing happening?

Jan 24, 2013 | Ford Cars & Trucks

1 Answer

Cant find indicator relay on 03 clio


if you have trouble with your indicators or hazard lights change the hazard light switch get one on ebay.

Jun 19, 2012 | 2003 Renault Clio

1 Answer

Turn signal not working


Press the Hazard switch on and check the turn indicator lamps. Replace the faulty lamps.
If the hazard lights do not work then the trafficator flash can is faulty provided the trafficator fuse is OK.
Check the fuse for the turn indicators, if it is blown the replace the fuse.

Dec 11, 2011 | 2002 Kia Rio

1 Answer

Indicator Problem


when you noticed the indicator being on solid, but flashing with the hazards, are you inside your car? I mean have you gotten out of your car to check if the bulbs are working when the indicator thrown and when the hazards are on. A hard on indicator usually means that you have a bulb burnt out. The hazards will still flash as normal when inside the car even if a bulb is burnt out because the hazards do not run via the Electronic Flasher Module. The EFM is what detects a burnt out bulb

Aug 24, 2009 | 2005 Audi A3

1 Answer

While driving my hazard lights keep going off at will what should i do ? The central locking unit is in situ but the there is no actual alarm and although you press the key and the indicator lights flash...


a hazard fuse is big and round mainly silver in color usually under the steering wheel or in the glove-box or on the side of the dash when you open the door

Apr 22, 2009 | 2007 Audi A3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...