Question about Dodge Sprinter

Open Question

How do i remove tension belt for 93 chevy corsica 3.1L?

Posted by Anonymous on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 337 Answers

SOURCE: remove and replace alternator for chevy corsica 1993

Posted on Dec 03, 2008

  • 13 Answers

SOURCE: need help with belt problem on 94 chevy cavalier

  1. Disconnect negative battery cable and remove coolant reservoir.
  2. Remove serpentine belt. Refer to Drive Belts, Mounts, Brackets and Accessories / Drive Belt. See: Drive Belt\Service and Repair
  3. Remove two generator bolts.
  4. Remove power steering pump and position aside.
  5. Remove tensioner bolts and tensioner.
  6. Reverse procedure to install, Torquing tensioner bolts to 37 ft. lbs.

Posted on Jun 30, 2009

  • 68 Answers

SOURCE: i wanted to change my thermostat in my 93 chevy

follow your upper radiator hose from the radiator back to the engine it will be under the housing hose connects to

Posted on Aug 10, 2009

  • 1 Answer

SOURCE: I am trying to replace the belts on my 93 Toyota

To remove the belt on the alternator side, loosen the the 14 mm nut and bolt that pivots the alternator and loosen the the 12 mm bolt that allows you to slide the alternator loose. The other belt that connects the power steering and the air condition compressor is a little trickier. You must loosen the the 14 mm nut that pivots the power steering but do not remove the nut completely. There are two other nuts, one 13 mm that can be reached below the vehicle looking upward that must be loosen. This creates the tension needed to release the belt. The last 14mm nut is located on a plate afixed to the side of the engine that is slotted. A special swivel type 14mm wrench is needed becuase there is not much room to work with. Once this is loose you will be able to loosen the belt to be able to take the belt off. If you can not take off this nut, your only recourse is to pry off the old belt with a screw driven and place the new belt in by hand by using the pulleys and rotate the belt manually on. This takes patience ans muscle. Once the belts are in place nmake sure to tighten the nuts and bolts to attain between 1/4" to 3/8" deflection arounf the center of the belts between the pulleys.

Posted on Jan 02, 2010

  • 241 Answers

SOURCE: Where is the crankshaft sensor on a 93 chevy

chevy corsica 3.1L crank sensor is located on the front of the engine above the starter.

Posted on Feb 28, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to move tensioner on 1991 chevy corsica

The tensioner is the smooth pulley(back side of the belt,no grooves)
Think it's a 15mm bolt, just "tighten the bolt" and the spring loaded tensioner will move The pulley is steel on the 4 cyl, plastic on the V-6 The tensioner bolt is left hand thread so it won't unscrew when you realese the tension.

Apr 11, 2012 | 1991 Chevrolet Corsica

1 Answer

Where is the crankshaft sensor on a 93 chevy corsica 3.1 engine?

chevy corsica 3.1L crank sensor is located on the front of the engine above the starter.

Feb 28, 2012 | 1993 Chevrolet Corsica

1 Answer

Where is the belt tension lever on a 1990 chevy corsica for installing an alternator

Your Corsica most likely has the 2.8 V-6...Look to the lower right side near the should see an arm with a pulley can use the socket end of your 3/8 drive socket wrench to release the belt tension, and remove the belt...the slot is near the middle of the tensioner arm...Hope this helps.

Mar 02, 2011 | Chevrolet Corsica Cars & Trucks

1 Answer

I'm replacing the drive belt "fan belt" on a 1995 chevy. corsica and need to adjust the tension

Apply tension to the belt until it is snug and has a live spring action when stuck with the hand dead center. For a more accurate deflection measure the distance from pulley to pulley and use 1/64th inch deflection per inch of belt length. For instance a 32" belt would require a deflection of 32/64" or 1/2". But saying all this I am confused. Your 1995 Corsica does not have a fan belt. The fan is electric. You car also has a serpentine belt which is self tensioning and not adjustable.

Oct 05, 2010 | 1995 Chevrolet Corsica

2 Answers

How do i install sepintine belt on a 3.1 chvy

no just slide it inward toward the block on the adjusting rail,after loosening the bolts.

May 31, 2010 | 1995 Chevrolet Corsica

1 Answer

I cant get the belt back on after i changed the water pump on my 1988 chevy corsica, i can get it close but not all the way

An extra set of hands may help,then with one guy holding back the tensioner you should be able to slide it onto the alternator pulley[if it's routed correctly,check the diagram under the hood for belt routing].

Dec 05, 2009 | 1988 Chevrolet Corsica

2 Answers

I wanted to change my thermostat in my 93 chevy corsica but do not know where it is located

follow your upper radiator hose from the radiator back to the engine it will be under the housing hose connects to

Aug 10, 2009 | 1993 Chevrolet Corsica

1 Answer

93 chevy lumina crank sensor location

front of engine just about 11:00 over crank pullry

Jun 12, 2009 | 1988 Chevrolet Corsica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides