Question about 2003 Mitsubishi Lancer

1 Answer

What size are my headlamp bulbs?

I have a 1998 mistubishi lancer evolution. When i bought it, it came with HID's and my passenger side has blown. I cannot for the life of me find out which bulb i have or what ones would fit. they are a hi/low combo bulb. any suggestions?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 123 Answers

Post a pic of the bulb. HID kits vary greatly. Either post a pic, or remove the bulb and the bulb number should be on the base.

Posted on May 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

proJekttaLon
  • 91 Answers

SOURCE: How do I replace the headlight in my 2005 mitsubishi lancer

Hi. While looking into your question I came across another posting of the same question for a 2004 Mitsubishi Endeavor and I believe it could help you. I put it in a link below. The instruction are basically the same. I hope this helps. Let me know if I can be of anymore assistance.

2004 Mitsubishi Endeavor Headlight Replacement

Posted on Nov 28, 2008

MarkTSI92TLN
  • 37 Answers

SOURCE: my headlights only work on highbeam.

Yes there is a relay switch that allows the low to high beam switch to occur. It shoud be mounted under the hood along the firewall. Check your manual too!

Thanks,

Mark

Posted on Dec 30, 2008

  • 8 Answers

SOURCE: Does a 2003-2007 evo hood fit a 2006 lancer ralliart?

i dont think so. most evo have different headlight shape than the ralliart, but my advice will be go to cardomain.com and look at evos or something or sign up and ask around. some very nice ppl on there for helpful info.

Posted on Jun 04, 2009

  • 32 Answers

SOURCE: Mitsubishi Evolution 8 engine management light

why does my evo 8 cut out after hard acceleration
if left on idle it is ok but after `few mins starts to almost die then picks up to 1500rpm and then back to normal

Posted on Aug 08, 2009

  • 1757 Answers

SOURCE: mitsubishi lancer evolution 8 timing belt

Sorry for the delay. I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.
Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2003/make/mitsubishi/model/lancer/2003_mitsubishi_lancer_timing_belt_diagram_marks.htm

Posted on Mar 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a passenger side headlamp out again. I just replaced both of them at Christmas. A coworker said that it was probably the ballast. Does my Mazda 5 have a ballast and if so how do I replace it?


it would only have ballast if they are hid headlights make sure your not touching glass part of the bulb when changing bulb oils from your fingers will cause bulb to burn out early

Apr 16, 2015 | 2006 Mazda 5 Touring

1 Answer

How do replace driver side headlight bulb? What size do I get?


Go to your local auto parts store.Ask at the counter,give them your make and model and year.

High & Low Beam Headlamp Light Bulb Size: 9007
Parking Light Bulb Size: 194NA
Front Turn Signal Light Bulb Size: 7507 Or 2827
Rear Turn Signal Light Bulb Size: 7507
Tail Light Bulb Size: 7443
Stop Light Bulb Size: 7443
High Mount Stop Light Bulb Size: 7506
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 921
Front Side Marker Light Bulb Size: 194NA
Rear Sidemarker Light Bulb Size: 7443
Dome Light Bulb Size: DE3175
Trunk/Cargo Area Light Bulb Size: DE3022

The bulb is in a socket which will twist out,then there may be a clip that holds the bulb in.

Jun 25, 2011 | 2003 Mitsubishi Lancer

1 Answer

2005 Lexus Rx330 Ballast problem??? First I saw my passenger side HID headlight was on and off and then mostly off. I thought the HID bulb burnt out. I bought a new one and replaced it. After I installed...


Well, we seem to have a real dilema here. I just searched the service manual for your 2005 RX330 and I cannot find any reference to a ballast for the HID headlamp bulbs. According to the wiring diagram, they are wired to the Headlamp Control Relays in Junction Block #2. (Right-hand side of the engine compartment) These relays are "Solid State", so my guess is that the balast for the HID may be built in to them. These are controlled by the Body Control Module. I would recommend scanning the body control module for fault codes before doing anything else. The first step in the diagnostic chart for the headlamp system is to perform a diagnostic systems check. There is a symptom chart to follow if there are no codes present, but if there are codes in the system, you could be shooting yourself in the foot trying to follow the symptom chart without first correcting any fault codes. This is not your fathers headlamp system - it is equipped with tracking control and automatic headlamp leveling...VERY sophisticated. Also lots of stuff that can break...this is what I call JOB-SECURITY- - LOL!

Apr 08, 2011 | 2005 Lexus RX330

3 Answers

I have a 2004 Nissan Maxima with hid headlights an the bulb is blown an i have replaced the bulb an it still doesn't work, i checked the fuse box inside an outside, is their any other fuses i can...


It sounds like you have wire problem. This problem can be manny problems from a short due to exposed wire or it is broken somewhere... ect. if it is not the wire check further back the line to see if the buse is recieving power. Or it could be as simple as the plug you put the bulb in has a broken contact tip

Mar 29, 2011 | 2005 Nissan Maxima

1 Answer

Headlamp bulb replacement. Driver side head lamp is out. Bought new bulbs. Owners manual says to contact dealership for replacement. How do I replace the bulb myself? 2007 Mazda6


I ASSUME they are just regular headlights....not HID....correct??? just take off the cover and there is a small clip, just unclip it and remove bulb. If they are HID, then you better not try it.

Nov 12, 2010 | Mazda MAZDA6 Cars & Trucks

1 Answer

How do I replace the headlight bulbs on my 2007 expedition?


SECTION 417-01: Exterior Lighting 2007 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/10/2006 Headlamp Bulb adobe.gif Printable View (255 KB) Expedition Headlampn0057191.gif
Item Part Number Description 1 13006/13005 Headlamp assembly (LH/RH) 2 13N021 Headlamp bulb

Navigator High Intensity Discharge (HID) Headlamp Bulbn0057192.gif
Item Part Number Description 1 13N019 HID bulb access cover 2 — HID bulb screws (2 required) (part of 13A006) 3 13N021 HID bulb 4 13A006 HID bulb electrical connector and harness Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamp with the bulb removed from the headlamp.
NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
All vehicles
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly in this section.
Expedition
  1. Rotate the headlamp bulb approximately 1/8 turn counterclockwise and remove the bulb from the headlamp assembly.
Navigator
  1. Remove the HID bulb access cover.
  1. Remove the 2 screws and the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n998988&c35=wsm%2cheadlamp%20bulb%2cs7j%2c417-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 04, 2010 | 2007 Ford Expedition Eddie Bauer EL

1 Answer

Change headlinght bulb


SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb adobe.gif Printable View (327 KB) Freestyle, Five Hundredn0035265.gif
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montegon0035266.gif
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.
  1. Remove the 6 screws and the headlamp bulb access cover.
Montego high beam bulb
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego HID bulb
  1. Release the spring retainer and remove the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n920901&c35=wsm%2cheadlamp%20bulb%2cs5f%2c417-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 02, 2010 | 2005 Ford Five Hundred

1 Answer

HID low beam headlight replacement for 2003 lexus es300


The HID bulbs are very easy to change, and can be bought online for much less than from the dealer. Check sites like xenondepot and Ebay for Phillips D2R (for reflector headlamps) HID bulbs and you can replace them yourself.

May 04, 2009 | 2003 Lexus ES 300

1 Answer

2004 Lincoln Navigator Low Beam Bulb replacement


your owner manual will list the bulb. It is expensive. tascafordparts.com for discount from Ford Dealer

here's 2003, don't have 2004

Navigator high intensity discharge (HID) headlamp
  1. Remove the front radiator air deflector.
  1. Remove the three bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
1c293b4.gif
8. Remove the headlamp bulb protective cover(s).
  • Remove the HID lamp cover.
  • Remove the high beam cover.
  • Disconnect the electrical connector and push the grommet into the headlamp assembly.
7adecf7.gif
  1. Release the spring tabs and remove the HID low beam bulb.
3394a45.gif

Apr 11, 2009 | 2004 Lincoln Navigator

2 Answers

Mitsubishi Evolution 8 engine management light


why does my evo 8 cut out after hard acceleration
if left on idle it is ok but after `few mins starts to almost die then picks up to 1500rpm and then back to normal

Oct 26, 2008 | 2004 Mitsubishi Lancer Evolution

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...