Question about 2008 Chrysler Sebring

Open Question

Where is blend door actuator located in 2008 sebring

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 47 Answers

SOURCE: 2008 sebring convertivble -m wont shift

if was running fine and and next day just wont go y woulthink is probably oyu input or output speed sensor,oyu need to check it with scanner and see if is that is the problem and not you tranny brain

Posted on Sep 27, 2009

jturcotte
  • 7754 Answers

SOURCE: location of blend door or

The temperature door actuator is located at the bottom of the heater housing at the center terminal. It looks like this:

6b48b5c.gif
To remove the actuator

  1. Remove the left and right underpanel silencer ducts.
  2. Remove the two retaining screws from the actuator which are accessible from the right side of the center stack.
  3. Remove the screw from the actuator on the left side.
  4. Pull the actuator straight down from the shaft and disconnect the electrical wire. Upon removal, matchmark the shaft position of the actuator, because the shaft on this motor is keyed.

Posted on Oct 03, 2010

chargerhp
  • 813 Answers

SOURCE: what blend door actuator controls what area

The driver and passenger area separately and must be recalibrate after installing and both are reversible same motor12_20_2011_6_26_43_pm.gif

Posted on Dec 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

On my 2010 dodge caliber once i remove section of dash to replace the door blend actuator is it visible or do i have to remove anything else?. Ronald mcgough.


I don't have a manual for your model, but did find a YouTube video for a 2008 Dodge Avenger showing the location of a couple of actuators on the HVAC box. It may not be exactly the same for your car, but it should give you an idea of what you're looking for.
There are a few more videos for Dodges, but mostly for Rams (pickups).
2008 dodge avenger blend air actuator location

Nov 22, 2016 | 2010 Dodge Caliber

1 Answer

2010 sebring heat on drivers side cold air on passenger side?


blend door actuator not working

1 - Blend door actuator 2 - Mode door actuator 3 - HVAC wiring harness


26340343-zk4yuwqxbgfnkewmrnymectq-4-0.gif

26340343-zk4yuwqxbgfnkewmrnymectq-4-1.jpg

Nov 04, 2016 | Cars & Trucks

1 Answer

I have a 2008 Chrysler Sebring. Were is the blend door located?


the blend door blends the hot and cold air from the dash that's used to heat and cool the passenger compartment

Apr 07, 2016 | Chrysler Cars & Trucks

1 Answer

Replace blend door in 07 Chrysler sebring


The most likely problem is either the blend door actuator or a broken blend door itself.
Both are only accessible by complete removal of the instrument panel(dash).
The blend door actuator can be tested with a Chrysler factory scan tool hooked up to the DLC(data link connector). If blend door actuator is working when tested with the factory scan tool, then blend door itself is at fault.
The only other way to test the blend door actuator is to test for 12v at connector, but you would have to remove the instrument panel in order to gain access to the actuator

Dec 24, 2014 | Chrysler Cars & Trucks

2 Answers

HVAC heater blend door actuator is not working


check HVAC fuse.if fuse okay heater control module could be the problem.

Nov 19, 2013 | Hyundai Cars & Trucks

1 Answer

2008 mercury marquis blender door location


The blend-air door actuator on a 2008 Merury Grand Marquis is located on the top forward area of the HVAC housing under the instrument panel. Complete instrument panel removal is required to access it.

May 26, 2012 | 2008 Mercury Grand Marquis

1 Answer

Location of blender door motor


The blend-air door actuator on a 2008 Merury Grand Marquis is located on the top forward area of the HVAC housing under the instrument panel. Complete instrument panel removal is required to access it.

May 26, 2012 | 2008 Mercury Grand Marquis

Not finding what you are looking for?
2008 Chrysler Sebring Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...