Question about 2002 Lincoln LS

1 Answer

How to remove the back seat - 2002 Lincoln LS

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 121 Answers

Push the back seat cushion toward the rear of the Taurus.

Position the back seat cushion at a vertical angle, and then pull it out of the vehicle

Pull the tab on the side of the rear seat to lower the back part of the seat. Remove the seat bolts with a 10mm ratchet or wrench. There are four bolts in all: two on each side.

http://www.xcardiag.com/

Position the seat back in its normal position (vertical).UOBD2 China Auto Diagnostic Tool Center for Workshop Wholesale DIY Drop...


Posted on Jul 01, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to remove back seat in 1972 buick skylark


Remove the seat cushion retaining bolts, detach the seat cushion and remove it up and out from the vehicle.

Remove the rear seat back retaining bolts at the bottom of the seat back. Pull up then out to disengage the upper frame from the hangers and remove seat back from the vehicle.

Installation is the reverse of removal.

Courtesy: Haynes GM repair Manual #38025. You can probably find a copy of it on Amazon or eBay cheap

Jun 20, 2011 | Buick Skylark Cars & Trucks

1 Answer

How to remove bottom of back seat need to remove seat to remove rear shocks..


PUSH IN CENTER FRONT EDGE CUSHION TO DISENGAGE PART OF SEATS WIRE FRAME FROM CLIPS.WITH CLIPS UNHOOKED LIFT UP AND REMOVE SEAT.IF REAR SEAT NOT HELD IN PLACE WITH CLIPS. LIFT UP THE REAR SEAT CUSHION AND PIVOT IT FORWARD. DETACH THE RETAINING BOLTS AT THE LOWER EDGE OF THE SEAT BACK AND IF NECESSARY REMOVE THE SEAT BELT ANCHOR BOLTS.LIFT UP ON SEAT BACK REMOVE IT..

Feb 06, 2011 | Jaguar X-Type Cars & Trucks

1 Answer

Truck lock is jammed by briefcase strap. can i get into the trunk from the back seat? such as does the back seat fold down?


I searched the owner's manual and there was no mention of folding the rear seats down. If you don't have a manual, you can get one here: http://www.extendedgmwarranty.com/owners-manual/buick/1999-Buick-Century.pdf

You can remove the seats following the instructions below from autozone.com.
Rear Seats
SEAT CUSHION


jturcotte_98.gif

Fig. Typical W-Body rear seat cushion removal

  1. Locate and remove the small bolts at the front lower edge of the seat cushion.
  2. Pull the tabs on the rear cushion retainers.
  3. Remove the seat cushion by lifting up and pulling out of the retainer.
  4. Installation is the reverse of the removal procedure. Make sure the retainer tabs are snapped into place. Tighten the bolts to 18 ft. lbs. (25 Nm).

SEAT BACK


jturcotte_99.gif

Fig. Typical W-Body rear seat back removal

  1. Remove the seat cushion as described above.
  2. Remove the anchor nuts securing the rear seat retainer at the bottom of the seat back.
  3. Grasp the bottom of the seat back and swing upward to disengage the offsets on the upper frame bar from the hangers.
  4. Lift the seat back upwards to remove from the vehicle.
  5. Installation is the reverse of the removal process. Make sure the hooks on the seat back are properly installed to the hangers. Tighten the anchor nuts to 89 inch lbs. (10 Nm).

Nov 07, 2010 | 1999 Buick Century

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?


Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Aug 21, 2010 | 1998 Ford Taurus

1 Answer

How do you remove the rear seat of 2004 honda accord


Release the two latches at the front of the seat cushion (pull back on the latches to release the front of the cushion).

Remove the seat cushion bolt and remove the cushion (it’s roughly in the center. You have to insert a socket extension between the back and bottom seat cushions to take it out, after you find it by pressuring the bottom cushion and looking back in there).

Remove the bolts (each side) securing the seat side bolsters (they are easy to see once the bottom cushion is removed), then remove the side bolters (gently release the clips that hold them in).

Pull the seat forward, then remove the fasteners securing the seat hinge (seat pivot bracket) and remove the seat backs.

Hope this helps you.

Dec 10, 2009 | 2004 Honda Accord

1 Answer

Mustang rear seat removal?


please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation
  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

May 04, 2009 | 2004 Ford Mustang

1 Answer

How to remove the back seat from my 1998 Mercury Villager


it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal
  1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
  1. Slide the bench seat forward to the center row seating position.
  1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.




  1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.




  1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.




  1. Remove the bench seat from the vehicle through the body side door opening.

Apr 30, 2009 | 1998 Mercury Villager

2 Answers

Getting back seat off


I imagine you're talking about the seat 'BOTTOM'? two 12mm bolts in between the seat back and bottom (at the seam where they meet). remove them and you can remove the seat bottom). Afterward, you will detect the fasteners holding the seat backs in place. If you remove those, the seat backs will come out.

Apr 10, 2009 | 1994 Hyundai Excel

3 Answers

Rear seat removal 2000 merc Villager


fold top seat down first
then there is seat clip push seat forward with upward motion
this releases back floor clamps once released pull seat back this releases the front clamps then pull seat out of back door

Jul 06, 2008 | 2000 Mercury Villager

Not finding what you are looking for?
2002 Lincoln LS Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...