Question about Cars & Trucks

2 Answers

How do I instal fuel pump behind c/head n do I have to bleed it

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 1,114 Answers

Fuel pump is self priming. Please list more info about your vehicle, model year, engine.

Posted on May 08, 2014

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

***BE SURE TO*** use vasoline on your 'PIN' to hold in place while bolting pump back on...!!! (so you don't make the same costly mistake I did by dropping the pump's pin down the engine {luckily I got it to drop all the way down to the oil pan...then just drained my oil to retrieve it, otherwise it was...start and...disassemble your block [at which point might as well rebuild it now that it's all torn apart?! LOL]
...and no you dont have to bleed it ...being its just like hooking up a water hose. . .and then turning on the water...lol

Posted on May 08, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do i need to bleed the injector pump on my isuzu bighorn 4gj2 after replacing the head? as it wont fire


anytime you disconnect the fuel rail, and if it has a bleeder/test port (looks like a tire Valve), Then it needs to be bled before fuel will reach the injectors. Also check Spark plug ignition as well make sure grounds have been returned properly.

Oct 13, 2015 | Isuzu Cars & Trucks

1 Answer

When blazer sets over 4 or 5 hrs has to crank several times before starting


The fuel pump is designed to turn on for a couple of seconds and prime with the key on. This is normal. If there is an extended crank, the fuel pressure may be bleeding back into the tank through the check valve of the fuel pump or there is an injector leak/fuel pressure regulator leak causing the pressure to bleed off causing the extended crank. Install a fuel pressure gague and monitor the pressure to see if it bleeds off to 0. If it does, one of the afore mentioned is causing the problem

Oct 04, 2015 | Cars & Trucks

1 Answer

1989 dodge ram 50 2.0 engine


Fuel pump
REMOVAL
  1. Disconnect the battery ground cable.
  2. Disconnect the fuel inlet, outlet and return hoses at fuel pump.
  3. Remove the two fuel pump mounting bolts, and remove the fuel pump.
  4. Remove the fuel pump gaskets and insulator.
Check for leakage, if there is oil or fuel leaking from the breather hole, oil seal or diaphragm of fuel pump, the pump is defective. Replace fuel pump as an assembly.

INSTALLATION
  1. Turn the crankshaft so the No. 1 cylinder is at top dead center on the compression stroke. NOTE : This is to minimize cam lift for ease of installation.
  2. Insert the push rod into the cylinder head.
  3. Install the new gasket and insulator, install the fuel pump.
  4. Tighten the bolts firmly.
  5. Connect the fuel hoses to the fuel pump ******* and tighten the hose clamps.
  6. START the engine.
  7. Check for fuel or oil leaks.

Jun 25, 2015 | Dodge Cars & Trucks

2 Answers

Got hit from behind in my 89 blazer no my car won't start


This tripped the inertia switch that cuts off the fuel pump some are located behind the left kick panel others are on the bulk head near a shock tower or strut mount ,may be installed in the rear quarter panels also

Sep 23, 2014 | 1989 Chevrolet S-10 Blazer

2 Answers

My 2002 buick century overheats and has no heat


Possible trapped in system. Bleed system, should have two small screw bleeders, one in front of left valve cover on pipe behind water pump and the other on coolant pipe outlet as you follow upper rad. hose towards engine. Engine cool, remove rad cap, open both bleed screws and fill rad until coolant flows free out both bleed ports. close both bleed screws, rad cap off, start engine and let idle until upper hose is hot to touch , shut off, let it cool down for 20 minutes, top up rad and install cap. restart car ,drive and check.

Jan 02, 2014 | 2002 Buick Century

1 Answer

Torque specs for 3.2 1995 heads on my isuzu... I need to fix the car ASAP....


Hi, to install follow the procedure below:


  1. Install new camshaft seals and retaining plates onto the cylinder. Tighten the right camshaft seal retaining plate 6mm bolts to 65 inch lbs. Tighten the left camshaft seal retaining plate 8mm bolts to 191 inch lbs.
  2. Thoroughly clean the cylinder head and engine block sealing surfaces.
  3. Place a new head gasket on the engine block and carefully position the cylinder head on top of the new gasket.

Do not reuse or apply oil to the cylinder head bolts.
  1. Install new cylinder head bolts and torque them in sequence to 47 ft. lbs. (64 Nm) for the M11 bolts and 15 ft. lbs. (21 Nm) for the M8 bolts.
  2. Install the dipstick tube bracket to the cylinder head.
  3. Connect the front exhaust pipes to the exhaust manifolds. Tighten the exhaust bolts to 48 ft. lbs. (67 Nm).
  4. Install the power steering pump bracket. Torque the mounting bolts to 34 ft. lbs. (46 Nm).
  5. Install the cylinder head covers.
  6. Install the timing belt and the auto tensioner (pusher). Torque the mounting bolt to 14 ft. lbs. (19 Nm).
  7. Install the timing belt cover and oil cooler hoses and bracket.
  8. Install the crankshaft pulley. Torque the center bolt to 123 ft. lbs. (167 Nm).
  9. Install the fan pulley assembly.
  10. Install the power steering pump.
  11. Install the accessory drive belts.
  12. Install the engine coolant manifold and the heater hose.
  13. Install the intake manifold. Torque the nuts and bolts to 17 ft. lbs. (24 Nm) in a crisscross pattern.
  14. Install the fuel injector connectors and the fuel hoses to the fuel rail.
  15. Install the common chamber. Torque the nuts and bolts to 17 ft. lbs. (24 Nm).
  16. Install the EGR valve assembly. Torque the mounting bolts on the valve side to 69 inch lbs. (8 Nm) and the bolts on the exhaust side to 21 ft. lbs. (28 Nm).
  17. Connect the evaporative emission canister purge hose.
  18. Connect the fuel pressure control valve vacuum hose.
  19. Connect the positive crankcase ventilation hose.
  20. Install the throttle body assembly. Torque the mounting bolts to 14 ft. lbs. (19 Nm).
  21. Connect the vacuum hoses to the throttle body.
  22. Install the ignition control module and the spark plug wires.
  23. Connect the MAP sensor; Canister vacuum switching valve (VSV); Exhaust gas recirculation (VSV); Intake air temperature sensor and ground connectors.
  24. Connect the vacuum booster hose.
  25. Connect the air vacuum hose.
  26. Connect the accelerator cable. Adjust the accelerator cable by pulling the cable housing while closing the throttle valve and tightening the adjusting nut and screw cap by hand temporarily. Now loosen the adjusting nut by three turns and then tightening the screw cap. Make sure the throttle valve reaches the screw stop when the throttle is closed.
  27. Install the cooling fan assembly and the upper fan shroud.
  28. Install the air cleaner assembly.
  29. Connect the negative battery cable.
  30. Refill and bleed the cooling system.
  31. Refill and bleed the power steering pump if necessary.
  32. Refill the engine with fresh oil.
  33. Run the engine and check for leaks and proper compression.

Best of luck............

May 30, 2011 | 1995 Isuzu Trooper

1 Answer

Torque specs for 3.2 1995 heads on isuzu rodeo heads


0900c152800622a3.gif

To install:

  1. Install new camshaft seals and retaining plates onto the cylinder. Tighten the right camshaft seal retaining plate 6mm bolts to 65 inch lbs. Tighten the left camshaft seal retaining plate 8mm bolts to 191 inch lbs.
  2. Thoroughly clean the cylinder head and engine block sealing surfaces.
  3. Place a new head gasket on the engine block and carefully position the cylinder head on top of the new gasket.

Do not reuse or apply oil to the cylinder head bolts.
  1. Install new cylinder head bolts and torque them in sequence to 47 ft. lbs. (64 Nm) for the M11 bolts and 15 ft. lbs. (21 Nm) for the M8 bolts.
  2. Install the dipstick tube bracket to the cylinder head.
  3. Connect the front exhaust pipes to the exhaust manifolds. Tighten the exhaust bolts to 48 ft. lbs. (67 Nm).
  4. Install the power steering pump bracket. Torque the mounting bolts to 34 ft. lbs. (46 Nm).
  5. Install the cylinder head covers.
  6. Install the timing belt and the auto tensioner (pusher). Torque the mounting bolt to 14 ft. lbs. (19 Nm).
  7. Install the timing belt cover and oil cooler hoses and bracket.
  8. Install the crankshaft pulley. Torque the center bolt to 123 ft. lbs. (167 Nm).
  9. Install the fan pulley assembly.
  10. Install the power steering pump.
  11. Install the accessory drive belts.
  12. Install the engine coolant manifold and the heater hose.
  13. Install the intake manifold. Torque the nuts and bolts to 17 ft. lbs. (24 Nm) in a crisscross pattern.
  14. Install the fuel injector connectors and the fuel hoses to the fuel rail.
  15. Install the common chamber. Torque the nuts and bolts to 17 ft. lbs. (24 Nm).
  16. Install the EGR valve assembly. Torque the mounting bolts on the valve side to 69 inch lbs. (8 Nm) and the bolts on the exhaust side to 21 ft. lbs. (28 Nm).
  17. Connect the evaporative emission canister purge hose.
  18. Connect the fuel pressure control valve vacuum hose.
  19. Connect the positive crankcase ventilation hose.
  20. Install the throttle body assembly. Torque the mounting bolts to 14 ft. lbs. (19 Nm).
  21. Connect the vacuum hoses to the throttle body.
  22. Install the ignition control module and the spark plug wires.
  23. Connect the MAP sensor; Canister vacuum switching valve (VSV); Exhaust gas recirculation (VSV); Intake air temperature sensor and ground connectors.
  24. Connect the vacuum booster hose.
  25. Connect the air vacuum hose.
  26. Connect the accelerator cable. Adjust the accelerator cable by pulling the cable housing while closing the throttle valve and tightening the adjusting nut and screw cap by hand temporarily. Now loosen the adjusting nut by three turns and then tightening the screw cap. Make sure the throttle valve reaches the screw stop when the throttle is closed.
  27. Install the cooling fan assembly and the upper fan shroud.
  28. Install the air cleaner assembly.
  29. Connect the negative battery cable.
  30. Refill and bleed the cooling system.
  31. Refill and bleed the power steering pump if necessary.
  32. Refill the engine with fresh oil.
  33. Run the engine and check for leaks and proper compression.

May 16, 2011 | 1995 Isuzu Rodeo

1 Answer

6.2 diesel will not bleed diesel


Make sure all lines are light when turning engine over.While turning engine over loosen the a line closes to pump or the fuel filter.You should get some fuel.Then continue on all lines working farther away.

May 02, 2010 | 1990 GMC C1500

2 Answers

How do you bleed air out of fuel lines after installing new fuel pump?


find fuel pressure test valve & hook up a gauge on it & do it the right way or stick something in the needle valve & release the pressure or raw fuel that will come out [[don't put ur face to close]]

Mar 14, 2010 | 1989 Ford F 150

1 Answer

92 dodge p u cummins eng power steering pump


to bleed the system fill the fuel filter then crack the inlet fule line turn over untill you get fuel then tightnline and start

Jan 11, 2009 | 1992 Dodge Ram 350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...