Question about 2007 Ford Edge SEL Plus

Open Question

How to replace hanger bearing on ford edge

Does the entire drive shaft need to be replaced?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: wheel bearing

u have to take the hub off. and press the wheel bearing out. it takes alittle time to do bc u have to take your rotor and brake assembly off to get to the hub.

Posted on Jun 25, 2008

Ad
  • 208 Answers

SOURCE: 1998 ford explorer font end

Has the car been in an accident? You may have to replace the upper ball joints as well. And you will have to get an alignment after that. I would get the tire set correctly before I started changing bearings. Of course it may be that the bearing is so bad that that is what is causing the wheel to lean so badly?
With the car jacked up, can you move the wheel laterally - it should be very tight.

Posted on Aug 10, 2008

  • 49 Answers

SOURCE: 1997 ford explorer AWD front drive shaft problem...

Try getting a free quote from several reputable shops before deciding to throw down your money on something your not certain of. Im not dissing your mechanic by any means, it doesnt cost anything to get another opinion or two or three....Its your money!

Posted on Feb 27, 2009

  • 234 Answers

SOURCE: can you replace rear wheel bearings ford explorer

You can replace the bearings. They are available here:
http://www.rockauto.com/catalog/x,carcode,1119697,parttype,1672

You should also be able to buy them at your local parts store.

I recommend buying the Haynes manual. It will help a lot with vehicle repairs

Posted on Apr 27, 2009

  • 23 Answers

SOURCE: replace front wheel bearings 99 ford explorer

not press fitted, standard tapered bearings, if 4X4 it is a little more involved, just dont misplace any of the smaller parts and you will be fine.

Posted on Aug 29, 2009

Testimonial: "thanks for the speedy reply and also for the right advice."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AFTER REPLACING U-JOINTS & HANGER BEARING ON MY 1995 VOLVO 960 I HAVE VIBRATION AT SPEED PARTICULARLY UNDER ACCELERATION. I TRIED ANOTHER SHAFT AND IS WORSE. I THINK IT MIGHT BE HANGER BEARING ALI


did you mark the two ends of the shaft at gearbox and diff
so they lined up again
with the center bearing replacement
did you mark the two halves before separating and replacing the center bearing
then make sure they lined up again

if vibration is there
you may need to go to a diff shop and have the drive shaft balanced properly

very informed drive shaft write up.. on volvos
Driveshaft Rear AxleDriveline Rear Axle
26328039-dr1l0prezoqh0gobrdoiolxi-5-0.jpg

Oct 26, 2016 | Volvo Cars & Trucks

1 Answer

Rebuilt trans installed in 2011. seal leaked in 2012 and was replaced. 2015 leaking again after 7000 miles. Why?


seals depend on a properly positioned shaft upon which they run
most people when reconditioning a transmission neglect to replace the output shaft ( drive shaft) bush in the transmission extension housing which allows the shaft to move concentric to the seal edge
the seal then cannot preform its duty as the seal surface is continually lost and so leaks
So it would appear that the bush is worn or in the case of transverse transmissions a possible failing bearing or bush

Aug 29, 2015 | 2002 Ford Thunderbird

1 Answer

Replace wheel bearing front awd 2010 ford edge


remove caliper, rotor, caliper bracket, lower ball joint shaft and two strut bolts. remove bearing housing and any snap rings. remove old bearing. replace and repeat in reverse. watch the abs sensor! costly if damaged. This is not for beginners...

Sep 19, 2014 | 2010 Ford Edge

1 Answer

How to replace a hanger bearing on a G20 CHEVY VAN


It is pressed in in, but most just replace the entire center support assembly it is allot easier.

Jun 27, 2012 | Cars & Trucks

1 Answer

Is a 2004 ford f-150 2wd carrier bearing.. ( mid-mount bearing ) on driveshaft replaceable, or do i have to replace entire driveshaft?


it is replaceable
normally it comes complete in the rubber mount
you will have to undo the drive shaft flange at the bearing
remove the drive shaft and take it to an accredited drive shaft repair shop or take the vehicle to an accredited drive line specialist shop
the repair will require that you place the flange back on the shaft after the bearing replacement in exactly the right position or you will get harmonic vibration after the job so talk with the experts first if you want to diy

May 09, 2017 | Gateway Cars & Trucks

1 Answer

How to change a hanger bearing on a 97 ford e 350


Best way to get it off the drive shaft is to cut it off with a torch. These will and do lock on to the drive shaft. and are almost impossible to get them off with out some sort of heat, high heat. With a torch you have to watch and only cut threw most of it. Do not cut the shaft, this is bad. If you are not good with a torch, then I suggest you remove the shaft and bearing and take it to a shop.

Aug 08, 2011 | Ford E-350 Cars & Trucks

4 Answers

Bad vibration in truck, not so much in the wheel but it's hard to tell. Starts around 30 to 40 mph and continues till 50 mph. A mechanic friend told me it may be the u-joints and/or (drive shaft) hanger...


that was good advice, it does sound like a u-joint, on these trucks the best way to check the joints is to remove the drive shaft, and flex each joint by hand to make sure each has free movement.

Mar 22, 2011 | 2002 Chevrolet Silverado 1500HD

1 Answer

I have a 2000 3.8L mustang, and the magnetic distributor shaft is squreeching as it spins. I took the cap off once and put a little high temp bearing grease down at the base and the noise stopped. It...


Well, I think that the entire shaft should be replaced if it can be done so economically.
I like your idea bout putting high temp bearing grease down at the base of it, though. Did you use moly grease?

Strange, when I looked up the 2000 3.8L mustang it said that the 3.8L and v8 engines used DIS, or distributorless Ignition System which doesn't use a conventional distributor.

Nov 06, 2010 | 2000 Ford Mustang

1 Answer

Hanger bearing needs to be replaced and a axle bearing


The carrier bearing for the axle will come with new 1/2 shaft.

Jul 13, 2010 | 2000 Ford Focus

1 Answer

Knocking and rattle hanger berring drive shaft


it needs to be checked out.It could be the bearing.

May 29, 2009 | 2003 BMW 325

Not finding what you are looking for?
2007 Ford Edge SEL Plus Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...