Question about Cars & Trucks

1 Answer

I have a 2000 jaguar s type, the buttons on the door panel are getting very hot.what would be the cause of this?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,509 Answers

Either the connectors to the buttons are corroded and have become high resistance or there is excessive or permanent current passing through the buttons.(is central locking permanently selected due to a fault?) You should strip down the door, examine/clean the connectors and measure the current if the connectors are ok. Under normal conditions there should be no current through the buttons.

Posted on May 08, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 231 Answers

SOURCE: what causes fault codes u1262

U1027 is invalid or missing data for engine R.P.M.
U1262 is communications bus fault.
Hope that this helps and answers your questions. Good luck and remember to rate all of the solutions that you get, thanx.

Posted on Oct 31, 2008

  • 1986 Answers

SOURCE: remove rear door panel on x type jaguar

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: 2000 jaguar s-type driver window will not roll up

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to see the motor, regulator, guide rails

Posted on Sep 10, 2009

  • 1986 Answers

SOURCE: how to remove the front dorr panel on s type

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls and mirror. Then you can access the bolts securing mirror onto the door

Posted on Oct 20, 2009

  • 288 Answers

SOURCE: I have a 2000 jaguar s-type Climate control does work

at this point what i would do is remove the temp door controller and see if you can manualy turn the temp door closed when you get it apart smply start the car get it hot and see if it will blow cool air when you turn the shaft to cold may be inside the case door problem or could be a recalbratoin problem you could also remove temp door motor turn temp too cold and watch too see if the motor is actually turning either way hot or coldt hats were i would start you can repost and i will try to help you further Thunderboltz

Posted on Feb 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed Fuel pump to 2000 jaguar and still no gas


check fuel shut off button located drivers side kick panel make sure button is pushed it...

Oct 10, 2014 | 2000 Jaguar S-Type

1 Answer

2000 Jaguar S type 3.0 Blows only cold air on full heat. Just replaced heater control valve with no change. Also flushed and replaced thermostat. Car operating temperaure is fine. Both heater hoses are...


Check the little pump below the brake booster for running and the coolant valve for movement.

Both hoses to fire wall should be hot.

Check for air lock in system.

Blend doors on this vehicle stop working....common complaint.

To verify Blend door movement, turn on ignition with engine off.

Run temp to max and the min..... listen under glove box for ( sliding ) motor noise as door swings from hot to cold.

This is a digital system needing a Jaguar scanner for diagnosis.

Jan 16, 2011 | 2000 Jaguar S-Type

1 Answer

My 2000 s-type driver door indicator light won't shut off


This problem is caused by a defective door ajar micro switch, this tiny switch is located on the door latch inside the door.

Jul 12, 2010 | 2000 Jaguar S-Type

1 Answer

How to remove doorpanel Jaguar xkr 03


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Oct 22, 2009 | 2000 Jaguar S-Type

1 Answer

How to remove the front dorr panel on s type jaguar to repair door mirror


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls and mirror. Then you can access the bolts securing mirror onto the door

Oct 20, 2009 | 2000 Jaguar S-Type

1 Answer

S Type JAguar Rear Door


First remove all of the screws, some will be hidden under plastic caps, then take a door panel tool (about $5.00 at a parts store) and work it around the panel popping out the plastic keepers. Be carefull and try not to damage the panel where the keepers attach, you can buy new keepers at any auto part store and even Lowe's and Home Depot carry them.

Jul 18, 2009 | 2000 Jaguar S-Type

1 Answer

DRIVER WINDOW WANT GO DOWN


hey jonest21,
I agree with emissionwiz, the fuse is most likely not the problem. Ive seen this numerous times. The window regulators on these older s types are very weak, and break all the time. They are fairly expensive to replace, and the dealership will charge at least an hour and a half for labor.
The door panel has to come off in order to get to the door panel. If you are goin to attempt this by yourself post it that you are, and ill give you more help on removing the parts.

May 19, 2009 | 2000 Jaguar S-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...