Question about 2003 Mazda Mazda6

Open Question

How to remove rear wheel bearing Mazda 2 - 2003 Mazda Mazda6

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: mazda rustler 160i wheel bearings

a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Posted on Dec 17, 2008

Ad
  • 67 Answers

SOURCE: changing a wheel bearing, 2003 mazda 6

to change that, using a hydraulic press is highly recommended. if you are DIY experienced, this trick works as well:

take a pice of a stable metal pipe, 10-20 cm long. and in diameter just a tick smaller than gross bearing size. take a very heavy tool and use the pipe to beat out the old bearing. dont be shy, needs a lot of power.

do not use this method to insert the new bearing. use a pice of wood instead (must sit stable on the outer bearing ring!!), lubircate a bit and beat carfully and very straigt in fractions of a mm. this is the difficult part and here the bearing may brake if you are too rough.

Not really recommend, but working when used with brain and care.

Posted on May 29, 2009

  • 713 Answers

SOURCE: how to change rear wheel bearing in Mazda 6 2002

Pretty easy job, if you have rear disc brakes on the car remove the caliper and brake rotor and you will see the hub bearing it just bolts one of two ways from the rear of the backing plate there will be 4 bolts holding it on, or there will be a dust cap in the center of the bearing, remove it and you will see a nut remove the nut and take the hub off and replace. If you have rear drum brakes remove the brake drum and remove the hub the same way should not have to remove the brake shoes at all if you are careful they will stay in place.

Posted on Sep 11, 2009

  • 819 Answers

SOURCE: how to replace wheel bearing hub

its not the same. the gm is a bolt on hub and bearing. on the mazda, its a press in. you need to remove the steering knuckle and use a hydraulic press to press the old one out and the new one in.

Posted on Nov 12, 2009

  • 1 Answer

SOURCE: The rear of my

You may want to check the rear endlinks. If one is loose the sway bar will make a loud clunk over bumps.

Posted on May 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rear wheel bearing on Tribute 2005..FWD


Jack up the car and place on stands remove wheels ,remove pin and nut ,remove the brake caliper,slide hub off ,remove old cup,s with a hammer and pin punch and fit new cups pack bearings with grease fit to hub,fit new seal.

Oct 09, 2016 | 2005 Mazda Tribute

1 Answer

Video of how to replace rear wheel bearings of a Mazda 323, 1.3,sting,front wheel power


take the rear hub off
you will need a hydraulic press or a vice to push bearing out and then in.

Jul 09, 2016 | Mazda Cars & Trucks

2 Answers

How 2 put in pioion bearing 96 mazda B2300 truck


You posted here meaning you have access to the internet, search YouTube and you should find a video showing you step by step. Or search for a forum for that vehicle and see if maybe the members have done it and provide great details. Lots of great info to be found that way.

Nov 26, 2014 | Mazda B2300 Cars & Trucks

1 Answer

Mazda mpv 2006 repack wheel bearing


There is a little difference between the front and rear. The days of packing wheel bearing is almost over. The front bearing you have to pull the hub and change to bearing. The rear wheel you have to change out the hub bearing and all. The front is a sealed bearing and not serviceable. Please rate my answer so I am rewarded points for it.

Jan 29, 2012 | Mazda Cars & Trucks

1 Answer

When sitting at a red light my Mazda 3 idles real funny...vibrating almost sounding like a cats purr?


2006 Mazda 3


Applies to 2006 Mazda Mazda3:
Available engines
4 Cylinders 2.0L MFI DOHC
4 Cylinders 2.3L MFI DOHC


Could be a number of things - you're going to end up checking the entire car.

Off the top of my head:
a) exhaust component has rusted loose (usually catalytic converter heat shield). Any loose exhaust component (hanger/muffler, etc.) will vibrate at idle.
b) glove compartment door - loose hinge
c) motor mount - rubber part of metal/rubber mount vibrates loose & falls out.
d) transmission mount - ditto.

The Maintenance manual for your car says:

Clicking noise at idle or driving
--------------------------------------------
1 Inspect Main (Crankshaft) Bearing - Excessive Bearing Clearance.
1 Inspect Rod Bearing - Incorrect Rod or Main Bearing Clearances.
2 Inspect Rocker Arm - Worn or Incorrectly Adjusted Rocker Arm(s).
3 Inspect Piston Ring Set - Worn or Broken Piston Rings.
4 Inspect Piston - Worn, Damaged, or Faulty Piston.
5 Inspect Fuel Line Assembly - Fuel Line Leaking.
6 Inspect Hose Clamp - Loose or Missing Fuel Line Clamps.

Tapping noise at idle
------------------------------
1 Inspect Valve Lifter - Insufficient Oil Supply.
2 Inspect Fan Blade - Broken, Missing, or Faulty Fan Blade(s).
3 Inspect Oil Pump Screen - Clogged Oil Pump Screen.
4 Inspect Oil Pump Drive Gear - Damaged or Faulty Oil Pump Drive Gear.
5 Inspect Exhaust Valve(s) - Burned, Worn, or Sticking Exhaust Valves.
6 Inspect Oil(Crankcase)Capacity - Lifters Need Additional Lubrication.
7 Inspect Oil Filler Cap - Oil Filler Cap Damaged or Missing.
8 Inspect Oil Pump - Damaged or Faulty Oil Pump.
9 Inspect Oil Filter - Old or Clogged Oil Filter.
10 Inspect Oil FLow Check Valve - Damaged or Faulty Oil FLow Check Valve Caused Loss of Oil Pressure.

Vibration while Accelerating
-----------------------------------------
1 Inspect CV Half-Shaft (Remanufactured) CCT - Worn or Damaged CV Half-Shaft.

vibration while braking
--------------------------------
1 Inspect Brake Rotor - Warped or Uneven Brake Rotor Surface.

Vibration while driving - entire vehicle
-----------------------------------------------------
1 Inspect Brake Rotor Specs - Warped or Uneven Brake Rotor Surface.
2 Inspect Ball Joint-Lower - Worn, Damaged, or Faulty Ball Joint.
3 Inspect Ball Joint-UPPER - Worn, Damaged, or Faulty Ball Joint.
3 Inspect Wheel Bearing-Front - Worn, Dry or Damaged Wheel Bearing.
5 Inspect Tie Rod End - Worn or Damaged Tie Rod Ends.
6 Inspect Wheel Bearing-Rear - Worn, Dry or Damaged Wheel Bearing.
7 Inspect Wheel Hub Bearing - Worn, Dry or Damaged Wheel Hub Bearing.

Vibration in rear axle area while driving
-----------------------------------------
1 Inspect U-Joint - Loose, Worn, or Damaged U-Joint.
2 Inspect Driveshaft - Bent, Loose or Unbalanced Driveshaft.
4 Inspect Differential Drive Pinion - Worn, Damaged or Broken Pinion Teeth.
4 Inspect Wheel Bearing-Rear - Worn, Dry or Damaged Wheel Bearing.
5 Inspect Pinion Bearing - Worn or Damaged Pinion Bearings or Yolk Shaft.


Vibration in steering wheel while driving
---------------------------------------------------------
1 Inspect Wheel Bearing-Rear - Worn, Dry or Damaged Wheel Bearing.

Vibration in tire/wheel area while driving
------------------------------------------
1 Inspect Wheel Bearing-Front - Incorrectly Tightened or Installed Wheel Bearing.

Vibration under vehicle while driving
---------------------------------------------------
1 Inspect U-Joint - Loose, Worn, or Damaged U-Joint.
2 Inspect Muffler - Damaged or Burned Out Muffler.

Vibration in rear wheeel area while driving
------------------------------------------------------------
1 Inspect Wheel Bearing-Rear - Worn, Dry or Damaged Wheel Bearing.

Dec 01, 2011 | 2006 Mazda 3

1 Answer

How do i pull the hub off my 2002 mazda , on drivers side front


REMOVAL & INSTALLATION Except Miata FRONT
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel

Jan 01, 2011 | 2002 Mazda Protege

1 Answer

How to change rear wheel bearing in Mazda 6 2002 1.8


Pretty easy job, if you have rear disc brakes on the car remove the caliper and brake rotor and you will see the hub bearing it just bolts one of two ways from the rear of the backing plate there will be 4 bolts holding it on, or there will be a dust cap in the center of the bearing, remove it and you will see a nut remove the nut and take the hub off and replace. If you have rear drum brakes remove the brake drum and remove the hub the same way should not have to remove the brake shoes at all if you are careful they will stay in place.

Sep 11, 2009 | 2003 Mazda Mazda6

1 Answer

I need to check rear brakes on mzda mx-3. The drum


remove screws and tap or hit with happer becarefull not hit wheel studs and dont inhale the brake dust when you hit the drum body

Apr 07, 2009 | 1995 Mazda MX-3

Not finding what you are looking for?
2003 Mazda Mazda6 Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...