Question about Cars & Trucks

Open Question

I have a 2003 ford ranger with a 4 cylinder, will a 2003 ford ranger with a v6 motor fit in mine?

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?


Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers

Jan 31, 2016 | Cars & Trucks

1 Answer

Ford ranger idle problems


had the same problem with my 2003 expedition replaced the coil packs and now it purrs like a kitten

Apr 06, 2014 | 2004 Ford Ranger

1 Answer

I need a picture for the layout of the cylinders for a 3.8 v6 ford


3.8 V6 1982 thru 2003

Ford Essex 90 degree
Windsor,Ontario


1,2,3 pass side
4,5,6.driver side

#1 & #4 at front of motor

transverse mount,then common sense
1,2,3,next to firewall

Jun 12, 2011 | Ford Lincoln Continental Cars & Trucks

1 Answer

The fireing order of ford ranger 1987


For the 1987 Ford Ranger:
I do not know if you have the 2.0L, 2.3L or the 2.9L; however I have included all below. They are the same for both the 2WD and 4WD.

For the 2.0L and 2.3L In-Line 4-Cvlinder:
Firing Order:
1-3-4-2
Cylinders:
(back)
|..4..|
|..3..|
|..2..|
|..1..|
(front)
Distributor:
................
[..........(+)] -long tab with screw
..4......2
..3......1
(+)- rounded tab screw

For the 2.9L V6:
Firing Order:
1-4-2-5-3-6
Cylinders:
........(back)........
|..3..|..........|..6..|
|..2..|..........|..5..|
|..1..|..........|..4..|
.......(front)
Distributor:
....1....4..(+)
6............2
(+)3....5

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


Jun 27, 2010 | 1987 Ford Ranger

2 Answers

Will a 87 ford ranger v6 4 wheel drive trans. fit in a 86 ford ranger 4 cyl 4 wheel drive


If automatic transmission wont work engine block's are not the same, if stander transmission you could swap out bell housing held on with four bolt's from one to the other. Good luck and hope this was very helpful.

May 19, 2010 | 1986 Ford Ranger 2WD

3 Answers

Where is the pcv valve located on a 2003 ford ranger


  • The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.
  • Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.
  • Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.
  • Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.
  • Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.
  • When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.
  • Feb 27, 2009 | 2003 Ford Ranger Regular Cab

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    12 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...