Question about 1991 Toyota Camry

1 Answer

1991 camry, power window for drive only,does not work

Put new master switch. Still same problem

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Toyota Expert
  • 294 Answers

You may have a broken wire between door and body remove harness and pull boot back repair has need good luck.

Posted on Jun 14, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bad_dog1
  • 104 Answers

SOURCE: Toyota Camry power windows not working from master switch

Their are two fuses that power this system. One is a 15 amp gauge fuse and the other one is a 30 amp main power fuse. You can also check the power main relay, your ignition switch, or i could possibly be a fault in the wiring

Posted on Mar 11, 2009

  • 13 Answers

SOURCE: 1991 toyota camry power doorlocks

I had the same vehicle with the same problems. Its the actual switches. Once they are exposed to the smallest amount of moisture they quit working.

Posted on May 10, 2009

ftw1952
  • 10319 Answers

SOURCE: '88 Camry Power Windows and Locks Won't Work

If you have continuity to the master switch the relay & breaker will be working just fine. Continuity tells me 12 volt current is passing thru as you put it. Check the switches to each window. The main circuit inside the switch may have a short in it

Posted on May 26, 2009

  • 106 Answers

SOURCE: power window toyota camry

Fuse box is by drivers left knee. Above this are the flashers and about 3 inches above this is the circuit breaker for the windows and door locks. breaker is silver, about 1/2 by 5/8 inch and in the center is the button you need to push in to reset. I used an unbent paper clip to press it. Make sure unit is not energized. May need to unplug breaker first. Press in center button until it clicks.

Posted on Jun 04, 2009

  • 318 Answers

SOURCE: installing power window on 1993 toyota camry

Take the door panel off. Disconnect the window and tape it up. Remove the regulator out off the door cavity.

Posted on Jun 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electric windows not working


It is probably a fault in the power window master switch, main relay, or the M fuse. See here p84

http://www.turboninjas.com/camry/be.pdf

Oct 07, 2012 | 1991 Toyota Camry

1 Answer

89 Camry passenger power window not working


I just solved this same problem on my 1989 Camry. The problem was a broken wire somewhere in the door or rubber boot, running between the master switch in the drivers door and the connector (E1, 10-pin blue connector) in the left kick panel. Put one lead of your ohm meter on the pin with the GRN/WHT wire (green with a white stripe) on connector E1, and the other lead of your meter on the same color wire at the master switch connector. If your problem is the same as mine you'll find this wire is broken (no continuity). Try some of the other wires in the same way to ensure you have the right wire bundle. The fun part was fishing a new 16 gauge wire through the boot. I used a fiberglass wire pulling rod from Harbor Freight tools, pulled a heavy string through, tied the new wire to it, and pulled it through. Tip: Pull in some extra wires at the same time; I found another broken wire that stopped my left rear window from working also. I cut the wires near each connector and crimped on **** connectors to splice in my new wires. Works great. Good luck -- Mark

Jun 20, 2012 | 1989 Toyota Camry

1 Answer

Wiring diagram for 1991 toyota camry master switch put in a new switch for the windows&locks but it does not work check the fueses they are good .


the harness that goes through drivers door from the inside of the car will usually have about 6-8 broken wires in it where the door opens and closes so much.there is also a circuit breaker in the left kick panel at the top of the fuse block. it will have a silver front with a hole in the center.take a straight pick and push it in the hole to see if it needs to be reset.let me know if all the windows and door locks quit working at the same time or over a period of time one then the other. if eveything quit at the same time then it is most likely a power problem.let me know...........

Jun 17, 2011 | 1991 Toyota Camry

1 Answer

My 91 camry has power windows, but the driver side controls wont roll down any of them [even the driver window] the window and door lock buttons work but thats it. I have switched it out with one from the...


I had the same thing happen on my 1989 model a few years ago, the part from the salvage yard was junk and when I bought a new one from the dealer at 120 dollers it worked fine. Since this is the master control it must be an excat match. Have you looked at the fuses and determined none of these are blown? Not much else it can be unless the wiring harness is bad. Make sure all the pin connectors on the switch are straight and clean.

Feb 27, 2011 | 1991 Toyota Camry

1 Answer

2 windows go down 2 windows dont ? driver side front works back no pasenger side front wont back will


check the wiring into the master switch on the drivers door. if it looks ok, then probably need to replace the switch.

Oct 14, 2009 | 1991 Toyota Camry

1 Answer

Passenger side window will not go back up


No.The drivers master power switch is probably bad.YOu will have to perform a test on the three other switches on the master. Check for power and ground when you push each putton.If the master switch fails the test you need a new master switch.

Aug 01, 2009 | 2004 Toyota Camry

1 Answer

02 toyota camry power windows all of them go down from master switch but only drver side widow comes back up with master switch,if i try to put left rear widow up with master switch right rear window comes...


left front door around the hinge area. there is a rubber boot inside that rubber boot are the wires for the windows. open it and you'll see some broken wires, stripped wires, etc. fix it.

Jun 03, 2009 | 2002 Toyota Camry

3 Answers

'88 Camry Power Windows and Locks Won't Work


at the drivers side panel there are 2 relays with metal tops on them.Push the little holes on top of the with a paper clip and reset them.This may help

May 26, 2009 | 1988 Toyota Camry

1 Answer

Toyota Camry power windows not working from master switch


Their are two fuses that power this system. One is a 15 amp gauge fuse and the other one is a 30 amp main power fuse. You can also check the power main relay, your ignition switch, or i could possibly be a fault in the wiring

Mar 11, 2009 | 1996 Toyota Camry

Not finding what you are looking for?
1991 Toyota Camry Logo

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...