Question about Dodge Cars & Trucks

Open Question

P0107 code i change the motor and sensors to match and now the car has a problem starting with the codes p0107 and p0129

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Code P0129

P0129 Barometric Pressure To Low

Posted on Feb 15, 2009

  • 120 Answers

SOURCE: 1999 intrepid stalls when hittin the gas

P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

P0122 Throttle/Pedal Position Sensor/Switch A Circuit Low Input

P1478 Battery Temp Sensor Volts Out of Limit
P0406 Exhaust Gas Recirculation Sensor A Circuit High


Posted on Mar 10, 2009

SOURCE: i have a 2005 dodge neon, throwing codes p0129,

you will have to deal with the u code first. This is a communication problem between computers. My first guess is you have a bad computer or an open wire somewhere. Their is no way a backyard mechanic can do this without the proper tools to diagnose and with the knowledge to not cause further damage.

Posted on Nov 02, 2009

  • 518 Answers

SOURCE: Have a 2006 dodge sprinter trouble code p0107..

Map sensor bad or vacuum &/or power to it missing. Map sensor located on intake manifold or firewall. It has a vacuum hose & electrical connector attached to it. To verify it is bad disconnect electrical connector to it while running. Idle should smooth out & run good. If so need to replace.

Posted on Jun 15, 2010

  • 2309 Answers

SOURCE: p0106 and p0107 codes are coming up on 2001 dodge

have you checked the egr system and check for a vacuum leak???

Posted on Nov 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 eclispe gt smells of gas, engine codes p0101, p0107


P0101 is the MAF (mass air flow) sensor that measure the amount of air entering the engine. Not enough air means rich running and a possible cause of fuel smell. Apart from running a little rougher there aren't always many signs that something is wrong.
P0107 is the MAP (manifold absolute pressure) sensor and responds to changes in manifold inlet pressure (vacuum). Problems cause include hard to start, long cranking times, sputtering/missing, blowing black smoke, poor fuel economy.

Nov 25, 2015 | Cars & Trucks

1 Answer

Hi!!I have a code on my 2003 nissan altima it reads p0107.I've changed the mfs its loosing power.Any suggestions?


code p0107 refers to manifold absolute pressure (MAP) sensor/barometric pressure (BARO) sensor--low input===causes wiring short to ground.---MAP sensor---Baro sensor----ECM
Maybe you didn't change the right sensor.

Mar 02, 2015 | Nissan Cars & Trucks

1 Answer

Fault code P0107 in 2001 grand cherokee


Code 107 means the MAP sensor signal is low. The problem could be the sensor, the wiring, or a major vac leak.

Aug 04, 2014 | 2001 Jeep Grand Cherokee

1 Answer

P0129 and p0441 x2


code p0129 refers to barometric pressure-two low===causes wiring---BARO sensor, ---mechanical fault
code p0441 refers to evaporative emission (EVAP) system--incorrect flow detected=== causes ---hose connection/s---intake leak--EVAP canister purge valve

replace the BARO sensor and the purge valve after seeing that the filler cap is on correctly.

Dec 12, 2013 | Cars & Trucks

1 Answer

I have a 05 Dodge ram 1500 90,000mi. and it start to bog and eng.light came on my codes were p0129-p0405-p0340-p0868 and pending codes were p0129-p0325-p0330-p0405-p0340. I had put a new map sensor in...


P0340 is for camshaft position sensor circuit malfunction so the problem can be in you hav already changed sensor, then you need to check wiring from sensor to ecu and if the wires are ok than check the ecu! It can be either of them cousing the problem.

Jan 30, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

What is check engine code c107?


do you mean P0107?iagnostic Trouble Code (DTC) P0107 - BARO Sensor Low Voltage Detecte 08.12.2010 · Posted in Automotive Diagnostic Trouble Code (DTC): P0107 - BARO Sensor Low Voltage Detected Description: Sensor operating voltage is less than 5.0 volts (VREF), as a result it failed below the minimum allowable calibrated parameter. Possible Causes: Open in the circuit, or short to ground VREF

Dec 23, 2010 | 2004 GMC Sierra

1 Answer

Code P0129


P0129 Barometric Pressure To Low

Feb 15, 2009 | 2003 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...