Question about 2005 Cadillac SRX

Open Question

Why does the Sunroof sunshade not go back from the rear of the shade.

The shade will move back from the front but bunches up at the rear of the sunroof opening, hanging inside the car.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Sunroof

Open the shade cover to access the sunroof from inside the car. On each side of the sunroof (driver and passenger) there is a black accordian looking cosmetic molding, toward the back side of the sunroof (rear of the car) stick your finger behind it at the top and pull you will now be able to see a T25 (torx) screw you will need to slightly loosen it on each side of the car if they are not already loose then push up on the center rear of the sunroof. you may want to have someone outside of the car to tell you the proper height, when you have the proper hight set tighten the screws then replace the molding. You are done, no more noise!

Posted on Nov 03, 2008

Ad
  • 39 Answers

SOURCE: Sunroof will not close. The sunroof is stuck in

Can't say for sure about this particular model, but most vehicles with sunroofs have a manual crank for situations like this. Generally it is located forward of the sunroof on the roof of the interior of the car, sometimes under a panel or interior light. This at least will get the roof closed until the problem can be fixed. It may also allow the sun roof to realign itself and help the electric crank to start working again.

Posted on Aug 13, 2009

  • 3 Answers

SOURCE: 08 SRX Ultraview Sunroof hard to close

Try spraying silicone lubricant in the groove that the rear brackets slide in (from the mid section of the roof to the rear).

Posted on Nov 29, 2009

bluebirdmate
  • 1190 Answers

SOURCE: the sunroof wont close automatically- when the

That has NEVER been an option on any cadillac since 1965 fo sure. If it was then it was some off the wall aftermarket item. If so then they need to fix it

Posted on Aug 29, 2010

  • 1243 Answers

SOURCE: sunroof wont open all the

sounds as if the position sensor in the roof control module has gone bad.

Posted on Jul 28, 2011

Testimonial: "i will check it out. thanks you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to install replacement sunroof motor on a 1999 Pontiac grand prix


Important: This sunroof system is timed from the factory in order to allow the actuator to shut off automatically when the sunroof window reaches a certain position. Use extreme care when removing the actuator from the sunroof module. This may cause the timing to be thrown off. This may damage to the sunroof. Anytime the actuator needs to be removed from the module, ensure that the sunroof window is in the fully closed position.
Remove the sunroof window. Refer to Sunroof Glass Panel Replacement .
Slide the sunshade fully rearward. Move the sunroof window to the vent position. Remove the sunroof screws (two on each side). Remove the sunroof window from the module.
Place the sunroof module in the fully closed position. Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior trim.
Tools Required ?€¢
J 38778 Door Trim Pad and Garnish Clip Remover


?€¢
J 2772-C Headliner Installer

  1. Remove the sunshades. Refer to Sunshade Replacement .
  2. Remove the overhead console, if equipped. Refer to Roof Console Replacement .
  3. Remove the sunshade retainers. Refer to Sunshade Anchor Replacement .
  4. Remove the power sunroof switch, if equipped. Refer to Sunroof Switch Replacement in Roof.
  5. Remove the sunroof trim lace, if equipped. Refer to Sunroof Seal/Molding Replacement in Roof.
  6. Remove the dome light, if equipped.
  7. Remove the coat hooks. Refer to Coat Hook Replacement .
  8. Remove the assist handles. Assist Strap Replacement
  9. Remove the rail lamp. Refer to Roof Side Rail Lamp Replacement in Lighting.
  10. Remove the windshield side garnish molding. Refer to Windshield Pillar Garnish Molding Replacement .
  11. Remove the upper quarter trim panels. Refer to Rear Quarter Upper Trim Panel Replacement .
  12. Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement .
  13. Pull down on the door opening weatherstrip seal on both the front and the rear doors.
  14. Remove the 2 rear retainers (2) using J 38778 Door Trim Pad and Garnish Clip Remover. Disconnect the headliner electric harness at the right side of the rear window shelf. Rotate the right front seatback to a horizontal position. Remove the headliner from the vehicle through the right front door.
Disconnect the electrical connector from the actuator.
Important: Before removing the actuator, ensure that the pins J 41718 are tight and holding the cable.
Thread the J 41718 into the front sunroof window screw hole in order to retain the cable adjustment. Remove the sunroof actuator screws. Remove the sunroof actuator from the module. Did you look for a video on youtube ?

Feb 27, 2015 | 1999 Pontiac Grand Prix

1 Answer

I have Mercedes SL500 2003. The hardtop in my car seems not fully closed, I can see that it is around 2 mm away from front seal. In addition, I can hear air leaking inside the car during driving. I heard...


  1. Move the sunshade rearward to the open position.
  2. Separate the mechanism covers (2) from the tabs (1) on the glass panel.

    813ada50.gif
  3. Verify the sunroof glass panel is in the fully closed position.
  4. Loosen the forward attaching screws (2) on each side enough to permit the front of the glass to adjust up or down.
  5. Adjust the front surface of the sunroof glass panel 0.00 mm to 2 mm (0.00 in. to 0.08 in.) below the top surface of the roof.
  6. Tighten the front glass panel attaching screws to 5.5 N•m (49 in. lbs.).
  7. Loosen the rear screws (2) on each side enough to make the rear adjustment.
  8. Adjust the rear surface of the sunroof glass panel 0.00 mm to 2 mm (0.00 in. to 0.08 in.) above the top surface of the roof.
  9. Tighten the rear glass panel attaching screws to 5.5 N•m (49 in. lbs.).
  10. Check for proper fit. If not OK, repeat glass panel adjustment.

    813bc829.gif
  11. Position the mechanism covers (2) over the glass tabs (1) between the locating features and seat fully.
  12. Verify sunroof operation and alignment.
There is a reprogramming from chrysler for the sunroof for recalibrating the sunroof for flushness also. the dealer will charge for this .You might want to do this first and then the adjust if not satisfied with the results.

Sep 10, 2012 | 2003 Mercedes-Benz SL-Class

1 Answer

Rear sunshade button doesn't work on Chrysler 300


I have same issue, the shade work with the touch screen from radio but the rear button on the back between the heated seat button dont work. please help if you know, i have a 2013 300s v6.
thanks

May 02, 2012 | Chrysler 300C Cars & Trucks

1 Answer

06 srx sunroof doesnt work


Sorry Bill but you don't the tool's or knowledge to take on this job . Control module's involved.
Which one does your vehicle have ?
Power Sunroof System Components -- CF5
The power sunroof system consists of the following components:
• Front glass control module and motor assembly
• Front sunshade control module and motor assembly
• Sunroof switch
• Front glass panel
• Front sunshade
• Power supply for the front glass control module and motor assembly logic: RAP relay
• Power supply for the power sunroof system: SUNROOF MOD fuse 40 A
Power Sunroof System Components -- C3B
The power sunroof system consists of the following components:
• Front glass control module and motor assembly
• Front sunshade control module and motor assembly
• Sunroof switch
• Front glass panel
• Front sunshade
• Rear sunshade control module and motor assembly
• Rear sunshade switch
• Rear sunshade
• Rear fixed glass panel
• Power supply for the front glass control module and motor assembly logic: RAP relay
• Power supply for the power sunroof system: SUNROOF MOD fuse 40 A

Aug 30, 2017 | 2006 Cadillac SRX

1 Answer

2002 Bonneville Sunroof. Fabric on sunshade was loose, was able to pull shade forward, glued fabric but the shade will not go back. Seems to be hitting something in the back. Can you help?


Hi


Inspect the sun roof of your Pontiac Bonneville to make sure it's seated evenly on your vehicle, not raising or lifting at one corner. Lifting indicates the presence of debris on the tracks, or a damaged seal around the sun roof.

Remove the trim on the interior of your Pontiac Bonneville and allow the interior material to drop. Use compressed air to blow dust and debris from the tracks that move your sun roof. Treat the tracks using 3-In-One Lubricant.

Check the Pontiac Bonneville's drain tubes for clogging. Two of these run down the front of your vehicle to the bumpers. Two run to the back, most often by your tail lights. Clear the tubes using compressed air and replace them.

Clean the sun roof's rubber seal with a damp, lint-free cloth. Inspect the seal as you clean


Please get back to us if you have further query else please accept the suggestion.
Thank you for contacting fixya.com



Jul 19, 2011 | Pontiac Bonneville Cars & Trucks

1 Answer

I have a 1999 chevy blazer I cannot close the


The sunroof is powered by the same circuit breaker that power's your power window, so if your windows work than the circuit breaker should be good. You needed test the switch to verify if works with; on the factory sunroof system the roof is controled by a sunroof module the module receives a signal from the switch then throws voltage to the sunroof motor. The motor and module are located between the sunroof assembly and windshield underneath the head liner. You would reconnected the switch and test to see if the sunroof motor is getting power when the switch is in use by testing the dark green wire when closing and a light green wire when opening. Test these wires at the sunroof motor with a ohm meter or test light. Also, check this procedure to repair...

GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide Power Sunroof - REMOVAL & INSTALLATION

Glass
  1. Close the sunroof and open the sunshade.
  2. If the piece of glass being removed is to be reinstalled, mark the location of the screws, this will ensure proper alignment during installation.
  3. Unfassten the screw that attach the sunroof glass to the sunroof assembly.
  4. Remove the glass from the vehicle.
To install:
  1. Place the glass into position and install the screws that retain the glass. Do not fully tighten the screws just yet.
  2. Adjust the glass so that the fit between the glass and the opening is equal at all four sides. The rear edge of the glass may be slightly higher than the front edge to reduce the wind noise.
  3. After the glass has been adjusted, tighten the screws to 31 inch lbs. (3.5 Nm).
  4. Check the operation and fit of the glass.

Motor
  1. Disconnect the negative battery cable.
  2. Remove the sunroof opening trim by starting at the **** joint and pulling the trim strip from the sunroof opening.
  3. Remove the headlines as follows:
    1. If equipped, remove the overhead or sunroof console.
    2. If equipped, remove the dome lamp.
    3. Remove the coat hooks and the assist handles.
    4. Remove the sunshade-to-roof screws, while pulling down on the sunshade base, push in on the extended screws, loosen the screw that attaches sunshade to the roof and pull down on the sunshade retainer while pushing in on the extended screw. Remove the retainer.
    5. Remove the windshield garnish moldings using trim removal tool J 38778 or its equivalent. Pull the molding away from the pillar and up to remove it.
    6. On four door models, remove the body lock pillar trim panels.
    7. Remove the roof rear header garnish molding using the trim removal tool. Insert the tool into the front edge of the trim and work along the front of the panel, from one end to the other. Unplug the cargo lamp electrical connection and remove the trim.
    8. On two door models, remove the rear seat upper seat belt anchor bolts.
    9. Remove the upper and lower front seat belt anchor bolts.
    10. Remove the rear seat belt lower anchor nut (two door models only).
    11. Remove the end gate or liftgate opening sill plate.
    12. Remove the jack storage cover (left side).
    13. Remove the upper body side trim panel screw (left side).
    14. Remove the upper body side trim panel and the body side front lower trim panel.
    15. Remove the headliner from the vehicle.
  4. Remove the sunroof console mounting bracket.
  5. Remove the straps that retain the wiring harness.
  6. Tag and unplug any necessary electrical connections.
  7. Unfasten the screws that attach the motor to the sunroof assembly.
  8. Remove the motor from the vehicle. Make sure that you do not move the sunroof mechanism while the motor is not in place.
To install:
  1. Place the motor into position and install the retaining screws. Tighten the screws to 31 inch lbs. (3.5 Nm).
  2. Attach all electrical connections that were unplugged.
  3. Attach the straps that retain the wiring harness.
  4. Install the sunroof console mounting bracket.
New headliners must be pierced to accommodate actual vehicle accessories.
  1. Install the headliner as follows:
    1. Install the body side front lower trim panel and the upper body side trim panel.
    2. Install the upper body side trim panel screw (left side).
    3. Install the jack storage cover (left side).
    4. Install the end gate or liftgate opening sill plate.
    5. Install the rear seat belt lower anchor nut (two door models only). Tighten to 59 ft. lbs. (80 Nm).
    6. Install the upper and lower front seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    7. On two door models, install the rear seat upper seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    8. Install the roof rear header garnish molding. Attach the cargo lamp electrical connection, place the trim in position and engage the molding retainers.
    9. On four door models, install the body lock pillar trim panels.
    10. Install the windshield garnish moldings. Place the molding into position, align the retainer clips with the slots and press into place.
    11. Place the sunshade retainer in position, install the screw and tighten to 10 inch lbs. (1.1 Nm). Position the sunshade, install the screws and tighten to 10 inch lbs. (1.1 Nm).
    12. Install the coat hooks and the assist handles.
    13. If equipped, install the dome lamp.
    14. If equipped, install the overhead or sunroof console.
  2. Install the sunroof opening trim. Start the trim in the center of the front of the sunroof opening and work around the perimeter.

Hope helps (remember rated this) Good luck.

Jun 03, 2010 | 1999 Chevrolet Blazer

1 Answer

The sliding panel under my sunroof is broke. Any suggestions? The Sunroof motor is working.


The sunshade clips are probably broken. Need to remove the glass panel. Note the position of the panel the frt and the rear. If not properly reinstalled you might get wind noise. Once you have the panel removed unscrew the clips from the sunshade. Carefully remove the shade and install the new clips.

May 26, 2009 | 2002 Volkswagen Jetta TDI

1 Answer

1998 Audi A6 sunroof is will close only half way.


make it go back to the open position,look down the side of the tracks in the roof that the sun shade slides in and you will probable find the guides for the sunshade are jamming up the tracks. only way to replace them<4 one in each corner> is to remove the glass section and then close sunshade that will give access to the 4 guides which are available from dealer as a kit

Mar 24, 2009 | 1996 Audi A6

1 Answer

Moonroof Problems


Heres the adjustment procedure.
ADJUSTMENT
813bc829.gif
  1. Move the sunshade rearward to the open position.
  2. Separate the mechanism covers (2) from the tabs (1) on the glass panel.

    813ada50.gif
  3. Verify the sunroof glass panel is in the fully closed position.
  4. Loosen the forward attaching screws (2) on each side enough to permit the front of the glass to adjust up or down.
  5. Adjust the front surface of the sunroof glass panel 0.00 mm to 2 mm (0.00 in. to 0.08 in.) below the top surface of the roof.
  6. Tighten the front glass panel attaching screws to 5.5 N·m (49 in. lbs.).
  7. Loosen the rear screws (2) on each side enough to make the rear adjustment.
  8. Adjust the rear surface of the sunroof glass panel 0.00 mm to 2 mm (0.00 in. to 0.08 in.) above the top surface of the roof.
  9. Tighten the rear glass panel attaching screws to 5.5 N·m (49 in. lbs.).
  10. Check for proper fit. If not OK, repeat glass panel adjustment.

    813bc829.gif
  11. Position the mechanism covers (2) over the glass tabs (1) between the locating features and seat fully.
  12. Verify sunroof operation and alignment.
There is a reprogramming from chrysler for the sunroof for recalibrating the sunroof for flushness also. the dealer will charge for this .You might want to do this first and then the adjust if not satisfied with the results.

Mar 18, 2009 | 2005 Chrysler 300

1 Answer

Need to know how to initialized the panorama roof.


start the vehicle.

push the center of the sunroof button (make sure its the center and not the forward or aft toggle) and hold it up. you'll have to hold it up for the entire time while it initializes.

after about 4 seconds the roof/shade will start to move. keep holding it until it goes through its entire process.

it will open/close the sunshade, tilt & close the roof and open and close the roof.

if this doesn't work, it may have other issues with the roof.

good luck

Mar 18, 2009 | 2005 BMW X5

Not finding what you are looking for?
2005 Cadillac SRX Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...