Question about 2006 BMW 550i Sedan

Open Question

Low pressure port 2006 bmw 550i - 2006 BMW 550i Sedan

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 3433 Answers

SOURCE: where is the location of the low-side pressure

Its on the large line, the one that gets cool when a/c is running.

Posted on Aug 14, 2009

  • 1675 Answers

SOURCE: where is the brake fluid fill cap on a 2006 bmw

hi this is normally located to the drivers side bulk head on the servo unit under the hood/bonnet

Posted on Mar 21, 2010

  • 170 Answers

SOURCE: does anyone know where is the low pressure port

never been fortunate enough to be able to look under the hood of my dream car, but if it were my bmw , i would look on the left hand side of the auto, near the firewall for a port sticking up. probably has a blue cap on it. the low pressure side will be between the ac compressor and the firewall. not the port by the radiator thats the high pressure side.

Posted on Jul 31, 2010

  • 252 Answers


Try turn the ignition put foot on the brake....Then mash gas pedal to the floor all the way down until it touches the floor and then back up 3 or 4 times..completely while foot is on brake .This works for GM and chrysler...It might help you I am not sure but it is worth a try.....>Some vehicles have a reset and a settings button on the dash board....If you have these buttons the pedal trick wont work.......Hope this helps.............................Metalpoet

Posted on Mar 07, 2011

  • 400 Answers

SOURCE: how can i know the firing order in a 2006 bmw 550i

When in it.....

Posted on Mar 31, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What causes engine misfire?

misfire is caused by poor gas, bad injector, poor fuel pressure in some cases, bad spark plug, wire, ignition coil, poor compression. check the computer for codes this will help in diagnosing the problem.

Jul 13, 2014 | 2006 BMW 550i Sedan

1 Answer

Why my 550i BMW emitting white smoke

Burning coolant. Blown head gasket or cracked cylinder

Jun 21, 2014 | 2006 BMW 550I

1 Answer

Car jerks before coming to a stop after about 1 hour drive

run fault codes and check the gear box sensors for faults. Have a pressure test done on the box to eliminate internal clutch pack / bands operation

Sep 28, 2013 | 2006 BMW 550i Sedan

1 Answer

How reset the flat tire on a 2006 bmw 550i

The tire pressure monitors I have seen require you to drive a certain distance after correcting the low pressure condition.I believe it uses the wheel speed sensors to detect a tire with low pressure(then one that is low will be essentially be giving a different reading because it is rotating more times at a given speed).I am assuming the system IS sensitive enough to get a false reading if one of the tires is a mismatched size,so keep this in mind.

Mar 30, 2012 | 2006 BMW 550I

1 Answer

Started driving my car this morning and immediately noticed that the clutch in my 2006 550i bmw felt funny, like it was easy to push. When I try to give it gas when taking off in first gear it shudders...

your clutch is slipping. this may be caused by worn pressure plate, clutch disc or oil seal failure. there are other components that may require attention, such as the clutch master and slave cylinders and fluid level.

Jan 08, 2011 | 2006 BMW 550I

1 Answer

The left front tends to skid on left turns even though turnning right at a much higher speed no skidding occurs

sounds like upper and lower ball joint have failed. also could be excessive play in wheel bearings. under inflated tyre pressures or over inflated tyre pressures.damaged shock absorer damaged bearing strut top. poorly alligned wheel allignment damaged or bent rim etc

Oct 18, 2010 | 2006 BMW 550I

1 Answer

Where is the brake fluid fill cap on a 2006 bmw 550i

hi this is normally located to the drivers side bulk head on the servo unit under the hood/bonnet

Mar 13, 2010 | 2006 BMW 550I

1 Answer


Put key fob in. do no hit brake. press start. the bell dings. hold the odometer reset knob found on the left of the speedo. bell dings again. scroll through items/pages with the buttons on the turn signal cruise control signal lever . Select oil hold odometer knob again. It will ask you if you want to reset? you press odometer knob again. Done. Your welcome.

Oct 09, 2009 | 2006 BMW 550I

Not finding what you are looking for?
2006 BMW 550i Sedan Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers


Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides