Question about 2007 Mazda 3
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Clean all dirt and/or grease from the
fuel filter fittings. "Quick Connect" fittings are used on models
equipped with a pressurized fuel system. These fittings must be
disconnected using the proper procedure or the fittings may be damaged.
The fuel filter uses a "hairpin" clip retainer. Spread the two hairpin
clip legs about 1/8 in. (3mm) each to disengage
it from the fitting, then pull the clip outward. Use finger pressure
only; do not use any tools. Push the quick connect fittings onto the
filter ends. Mazda recommends that the retaining clips be replaced
whenever removed. The fuel tubes used on these fuel systems are
manufactured in 5/16 in. and 3/8
in. diameters. Each fuel tube takes a different size hairpin clip, so
keep this in mind when purchasing new clips. A click will be heard when
the hairpin clip snaps into its proper position. Pull on the lines with
moderate pressure to ensure proper connection. Start the engine and
check for fuel leaks. If the inertia switch (reset switch) was
disconnected to relieve the fuel system pressure, cycle the ignition
switch from the OFF to ON position several times to re-charge the fuel system before attempting to start the engine.
Remove the "hairpin" clip retainers to access the fuel line fittingsThe inline reservoir type fuel filter should last the life of the vehicle under normal driving conditions. If the filter does need to be replaced, proceed as follows:
CAUTIONIf the fuel filter is being serviced with the rear of the vehicle higher than the front, or if the tank is pressurized, fuel leakage or siphoning from the tank fuel lines could occur. to prevent this condition, maintain the vehicle front end at or above the level of the rear of vehicle. also, relieve tank pressure by loosening the fuel fill cap. cap should be tightened after pressure is relieved.
Posted on Oct 17, 2008
The fuel filter is attached to a bracket located in the left rear of the
engine compartment. Look down in the space between the master cylinder
fluid reservoir and the rear of the air filter compartment, you will be
looking at the top of the fuel filter cannister. It's very hard to get
Hope helped (remember comment and rated this).
Posted on Apr 10, 2010
The fuel filter is located on the right hand side of the car .It is under a plastic shield just in front of the rear right side wheel .
In some cars of mazda 3 the
filter on Mazda 3 models is part of the fuel pump assembly.
The fuel filter on all Mazda cars can be located on a bracket in the left rear of the engine compartment, next to or beneath the brake master cylinder fluid reservoir or as part of the fuel pump assembly.
Open the hood and locate the fuel filter. If the fuel filter is not in the engine compartment, follow the fuel line from the tank until the fuel filter is located. Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
Posted on Jul 02, 2010
Tips for a great answer:
Jul 25, 2017 | Cars & Trucks
Sep 09, 2012 | Mazda Cars & Trucks
Feb 27, 2011 | 2004 Mazda MPV
Jul 14, 2010 | 1999 Mazda 626
Jul 02, 2010 | 2004 Mazda 3
Jun 15, 2010 | 2001 Mazda Protege
Nov 09, 2009 | 2004 Mazda 6
Oct 12, 2009 | 2006 Mazda Miata
29 people viewed this question
Usually answered in minutes!