Question about 1995 Nissan Pathfinder

1 Answer

No reverse on 95 Pathfinder

I was told to replace the TCM on the 95 Pathfinder in order to fix the Reverse on it. but I do know where to locate the TCM

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

It is under the seat.

Posted on Jun 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need diagram for 1995 subaru legacy automatic transmission. 176K , Reverse went out about 10 months ago but all other gears shift fine. Have driven from San Francisco to Lake Tahoe 4/5 times with no...


It's a bad solenoid. Reverse and low gears work off the same set of clutches. If you have first gears , then its a solenoid problem. I would first start by pulling plugs, transmission, TCM and everything in between. Check for corrosion, Use an ohm meter and check the wires for continuity. On some models the safety neutral switch/ range selector switch has a lot to do with how the transmission shifts. If the tcm can't read the switch it wont send power to the solenoid. so far I haven't found a place that will sell just solenoids. You have to buy the whole package. These start at about $200.00

Aug 14, 2011 | 1995 Subaru Legacy

2 Answers

I bought a 1998 mitsubishi eclipse and the check engine light came on we hooked up the machine to diagnos it and we got 2 codes po700 and p1784 . we are wondering what the codes mean and how to fix the...


DTC 1784: LOW-REVERSE PRESSURE SWITCH
1.Remove transaxle relay from connector. Turn ignition on. Install scan tool and observe low-reverse pressure switch condition. Apply battery voltage to transaxle relay connector terminal No. 8. If low-reverse pressure switch stays off, go to next step. If low-reverse pressure switch turns on, go to step 4 .

2.Raise vehicle enough to allow drive wheels to spin freely. Test low-reverse clutch hydraulic pressure. See HYDRAULIC PRESSURE TESTS under TESTING. If low-reverse clutch pressure test is not within specification, internal transaxle failure exists. If low-reverse clutch pressure test is within specification, observe scan tool.

3.If low-reverse pressure switch turns on, trouble code is intermittent. Check wire harnesses and connectors for damage or poor connection. If low-reverse pressure switch does not turn on, replace solenoid and pressure switch assembly. Recheck trouble codes. If trouble code resets, replace TCM.

4.Check and repair wiring harness between transaxle relay connector and solenoid and pressure switch assembly connector. If wiring harness is okay, check wire between TCM connector terminal No. 10 and solenoid and pressure switch assembly.

5.If wire between TCM connector terminal No. 10 and solenoid and pressure switch assembly is okay, check TCM and solenoid and pressure switch assembly connectors. Repair connectors as necessary. If connectors are okay, recheck trouble codes. If trouble code resets, replace solenoid and pressure switch assembly. Recheck trouble codes. If trouble code resets, replace TCM.

P0700-The Transmission Control Module (TCM) monitors the malfunction of sensors and actuators relating to transmission control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transmission controls.

I would try disconnecting he battery and letting it sit for 5 minutes, then hook it back up to see if they return-the 700 code is probably related to the 1784 code, that seems to be your main issue.

Jun 06, 2011 | 1998 Mitsubishi Eclipse

1 Answer

95 ARORA shitfs hard into reverse ans drive but shifts fine while drivivg.i was told prob a solenoid in trans.how do i fix?


The most common issue with these cars is a sensor that is located inside the transmission that gets splashed with transmission oil and prevents it from working. The car reports a code PO717... which is the "Input Turbine Speed Sensor" is not reporting. This will cause the transmission to shift roughly out of park and reverse. The transmission will need to be disassembled to have the sensor replaced. You can still drive the car but it will eventually cause the transmission to fail completely.

Mar 14, 2011 | 1995 Oldsmobile Aurora

1 Answer

I have a 95 pathfinder an lost reverse all others work


Gearbox needs to be looked at. Probably it will have to be removed and the main and lay shafts viewed to see what needs replaced. A costly job.

Jan 06, 2010 | 1995 Nissan Pathfinder

2 Answers

Reverse just quit on '95 Pathfinder


If it is an automatic transmission it probably needs transmission fluid. If a standard shift check and adjust shift linkage.

Jul 08, 2009 | 1995 Nissan Pathfinder

1 Answer

Reverse suddenly quit 95 toyota camry 4cyl auto


Check your transmission fluid level asap. if the level is good, you will need to inspect the shift solenoids located inside the transmission pan. replace any solenoids that are proven to be faulty. i would also advise to test the pcm/tcm for its operational value as well. this device controls the shifting patterns of the auto trans.

while checking the solenoids, if you notice any metal fragments on the bottom of the pan, this will be a sign of major gear friction. you should re build in this case.

May 24, 2009 | 1995 Toyota Camry

1 Answer

No reverse gear - auto trans


Hi mjpgd,
I have the same problem on my 96 Pathfinder. I just spoke with a mechanic who said this is most often due to a knicked seal in the rear part of the transmission. The leak results in pressure loss, making the system reluctant to shift into reverse. He said the fix is replacing the seal. The part lists at approx $200 Canadian ($190 USD), but unfortunately it takes lots of labor. The whole transmission needs to be removed and taken apart to replace the seal. The total bill is esitmated at $1500 Canadian. Youch. I'm not sure if I'll proceed with the repair, given the age of the vehicle.

May 07, 2009 | 1995 Nissan Pathfinder

1 Answer

2005 Pathfinder no reverse lights


On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

Apr 20, 2009 | 2005 Nissan Pathfinder

Not finding what you are looking for?
1995 Nissan Pathfinder Logo

Related Topics:

747 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...