Question about 2005 Ford Focus

Open Question

Toque spec for 2005 ford focus rear wheel bearing

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 208 Answers

SOURCE: wheel bearing

The bearing might be a hub assembly in a Taurus, but it is a press in unit on a Focus. I have done it myself.

Posted on Jul 16, 2008

  • 4369 Answers

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Posted on Apr 10, 2009

  • 27 Answers

SOURCE: replace rear wheel bearing 2002 ford explorer 4x4

you must remove brakes, then remove axle nut, then remove upper control arm and finally tie rod stabilizer, remove axle from car then bearing can be accessed. this is a difficult job that requires special tools so be careful

Posted on Aug 15, 2009

  • 141 Answers

SOURCE: fixing a 2003 ford focus front wheel bearings

remove the hub and spinle ,tie rod end ,axle nut.ball joint,and seperate from strut and then have new bearing pressed in...or rent a bearing press that works with an impact wrench,but they are a little hard to work with...good luck...lee

Posted on Sep 07, 2009

  • 6 Answers

SOURCE: ford fiesta 1999 rear wheel bearings

yes it is one big nut, however it looks like 4 individual nuts due to the fact that they are a thinly stacked layer or thin nuts held together by what you called the tab washer............only way to replace is to get a new one from ford........

Posted on Sep 19, 2009

Testimonial: "Thank-you for that, I have ordered a new one from the ford dealers. I just wonder why the 4 nuts were fitted in the first place? thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque spec for the rear wheel hub bearing nut?


Torque spec is 200Nm / 148 ft lbs for the axle nuts front and rear

May 02, 2015 | 2005 Ford Freestyle SEL

1 Answer

2001fordfocusrearwheelbearingreplacement


The rear bearing is a complete unit held on by a single centre nut. Remove the hub, press out the old bearing, refit the new one. This is a safety critical item and require trained knowledge and workshop tools. A new nut is required for restaking when correctly torqued up.
Go online to images for Ford Focus wheel bearing to get an idea of whats involved.

Aug 15, 2014 | 2001 Ford Focus

1 Answer

2005 1.3i ford bantam front wheel bearings torque settings?


Get a Hanes manual from PepBoys for your vehicle.They carry them all.You'll find all specs in there.

May 02, 2014 | 2005 Ford Bantam 1.3i

2 Answers

Fixing a 2003 ford focus front wheel bearings


remove the hub and spinle ,tie rod end ,axle nut.ball joint,and seperate from strut and then have new bearing pressed in...or rent a bearing press that works with an impact wrench,but they are a little hard to work with...good luck...lee

Sep 07, 2009 | 2003 Ford Focus

2 Answers

1996 Jaguar XJ6 - seeking toque spec for front hub bearing?


They are taper roller bearings, when new something like 8 or 10 pound feet, used ones tigten until only a little play exists (if you have steel wheels leave the wheel on and it is easy to feel the play even if packed with fresh grease) If you overtighten they will growl and overheat and fail

May 23, 2009 | 1996 Jaguar Xj Series

1 Answer

What torque for rear wheel bearing Ford Focus 2000


Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Jan 26, 2009 | 2000 Ford Focus

2 Answers

Tire wear


does the car make noise from the rear when you go at a high speed. If it does it may be your bearings. I had my bearing wear out on me at 15000 miles.

Jun 27, 2008 | 2005 Ford Focus

Not finding what you are looking for?
2005 Ford Focus Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...