Question about 2008 Dodge Caliber

Open Question

HOW TO INSTALL SHIFT LEVER BUSHING - 2008 Dodge Caliber

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just rebuilt my 97 s10 getrag nv1500 trans. the shifting pattern is off and i have no rev or 5th gears.


On reviewing the manual, there are two cautions regarding installing the shift shaft that may be the source of your problem. One, the shaft must be installed with the detents at the front end of the shaft facing upwards. These detents are what the ball/spring seat into when the shaft moves forward/aft (like into 1st/2nd gear). The shaft can be installed 180 degrees out, but you would not feel the shifter 'lock' into gear.
The second caution seems more probable. When inserting the roll pin holding the shift shaft lever and bushing onto the shift shaft, the roll pin must be driven down flush with the surface of the shift shaft lever. If not driven flush, it can bind on or interfere with the movement of the bushing, possibly preventing the lever from being able to engage all of the three shift forks (3/4, 1/2, 5/rev). There are two roll pins used with the shift shaft. The shorter one (7/8") is used to secure the shift shaft lever/bushing and the longer one (1 1/4") to secure the shift socket in the rear.
Unfortunately, confirmation will require removal and partial disassembly (removal of the front case) to confirm.

Sep 14, 2016 | Chevrolet S 10 Cars & Trucks

2 Answers

I have a 1989 300zx manual trans. Will not shift in to reverse what coud be the problem


Sounds like linkage from shift lever to transmission or the bushings on the linkage points. A "sloppy" shift lever with similar bushing problems may be the problem.

Mar 23, 2015 | 1989 Nissan 300ZX

1 Answer

Has reverse no foward


If automatic most likely lingage between transmission and shift lever. possible bushings associated with and possibley the shift lever pivot bushing if it's "sloppy". Similar if, Standard but could be broken shift fork inside transmission.

Mar 17, 2015 | 2002 Ford F150 Regular Cab

1 Answer

Currently my 1999 SL1 Saturn will not change gear, and I mean that the shift stick doesn't register there being any gears at all. It's stuck in third gear when it broke and now I'm trying to...


YOU NEED A HAYNES REPAIR MANUAL IT CAN HELP YOU, YOU HAVE TO REMOVE CONSOLE, PUT SHIFT LEVER IN SECOND GEAR AND DISCONNECT THE CABLE END FROM THE LEVER.DEPRESS THE TWO TABS ON THE CABLE HOUSING USING PAIR PLIERS REMOVE THE CABLE FROM THE SHIFTER.YOU HAVE TO MOVE CARPET UNDER DASH AWAY FROM SHIFT CABLE,YOU HAVE TO GO UNDER HOOD REMOVE AIR INTAKE DUCT ASSEMBLY DISCONNECT THE CABLE END FROM THE SHIFT LEVER ON THE TRANSAXLE YOU HAVE TO DEPRESS THE TWO SHIFT CABLE HOUSING RETAINING TABS AND DETACH THE CABLE HOUSING FROM ITS BRACKET ON THE TRANSAXLE.

Aug 09, 2011 | 1999 Saturn SL

1 Answer

1999 ford gear handles moves but won't select gear and the car is still in park


Two things happen. On collum shift cars and trucks the bolts work loose out of the shift lever to the cable under the dash where the shift cable connects to the steering collum. the cable connects to a lever that is connected the the shift tube ( part of the steering collum ) bolt heads are 30 torx. the other thing that happens is the cable comes off the trans mission lever and it just snaps on. The bushing waers out and the cable just comes off the pin on the lever coming out of the transmission. Front wheel drive cars it's on the top and rear wheel and trucks it's on the side ( happens less on these and then the cable can break it'self, and the shift cable has to be replaced sometimes if the bushing in the end fails at the transmission end.

Jun 10, 2011 | Ford Taurus Cars & Trucks

1 Answer

How do you remove the manual shift lever from a 1994 acura legend


YOU HAVE TO UNSCREW THE SHIFT LEVER KNOB. REMOVE THE CENTER CONSOLE.REMOVE THE RUBBER SHIFT LEVER BOOT AND THE DUST SEAL.YOU NEED TO RAISE SUPPORT VECHICLE ON JACKSTANDS ON LEVEL SOLID GROUND.YOU HAVE TO DISCONNECT THE EXTENSION ROD FROM THE TRANSAXLE.SIMPLY REMOVE THE BOLT THAT ATTACHES IT TO THE EXTENSION BRACKET.TO DISCONNECT THE SHIFT ROD FROM THE TRANSAXLE PUSH THE DUST BOOT FORWARD REMOVE THE CLIP AND DRIVE OUT THE SPRING PIN WITH A PIN PUNCH.DISCARD THE SPRING PIN.DO NOT REUSE IT.TO DISCONNECT THE REAR END OF THE SHIFT ROD FROM THE SHIFT LEVER REMOVE THE NUTS AND BOLTS.THEN REMOVE THE TWO NUTS AND WASHERS THAT RETAIN THE CHANGE BALL HOLDER TO THE UNDERSIDE OF THE EXTENSION ROD AND REMOVE THE CHANGE BALL HOLDER LOWER THE SHIFT LEVER DUST SEAL,SHIFT LEVER BALL SEAT,SHIFT LEVER AND EXTENSION ROD.INSPECT THE BUSHING AT THE FRONT END OF THE EXTENSION ROD AND REPLACE IT IF ITS CRACKED TORN OR WORN. REPLACE THE ORINGS IN THE BASE OF THE LEVER.BESURE TO LUBRICATE NEW O RINGS AND BUSHINGS WITH A SILICONE GREASE.USE A NEW SPRING PIN TO ATTACH THE SHIFT ROD TO THE TRANSAXLE.INSTALL EVERY THING BACK VISA VERSA.

Mar 02, 2011 | 1994 Acura Legend

1 Answer

Gear shift lever in column is loose


your problem with the gear selector is in the item 25 these are 2 plastic bushings that wear out and cause the gear selector feels loose, you should also check the item 27 this item has one or two screws loose and cause the gear selector feels loose

ganyapr_8.gif

Item Part Number Description 10 3F609 Tilt Wheel Handle and Shank 11 7361 Column Shift Selector Lever Plunger 12 7210 Gearshift Lever 13 3D657 Steering Column Shaft 14 7B071 Transmission Control Selector Lever Plunger Spring 15 7G357 Gearshift Lever Pin 16 7212 Shift Tube 17 N806582 Tilt Column Pivot Screw 18 7C464 Transmission Control Selector Lever Spring Clip 19 7E400 Gearshift Tube Bushing Clamp 20 - Spacer (Fixed Column) 21 3E729 Steering Shaft (Fixed Column) 22 3F527 Lever Assembly (Manual Transmission) 23 3F530 Pin (Manual Transmission) 24 3F752 Brake Shift Interlock Solenoid 25 7335 Gearshift Lever Socket Bushing 26 7A216 Transmission Shift Selector Position Insert 27 7302 Transmission Selector Lever Arm and Support 28 7E395 Shift Cable and Bracket 29 7210 Gearshift Lever 30 3E691 Steering Column Lock Pawl

Feb 13, 2011 | 1998 Ford Econoline

1 Answer

Clucth not disengauging....


try this.you have 2 shifter cables.one is select cable the other is shift cable.first put the transmission selector lever in neutral.then move transmission shift lever to 4th gear.depress clutch to if necessary to shift.move the shift lever to the 4th gear position until contacts stop.then you turn the adjuster turn buckle so the shift cable eye aligns with the eye in the gear shift lever.when installing the cable eye. make sure the flange side of plastic bushing at the shift cable end is on the cotter pin side.the cables should be adjusted so the clearance between the shift lever and both stoppers are equal when the shift lever is moved to 3rd and 4th gear. move the shift lever to each position and check that the shifting is smooth.

Jul 12, 2009 | 1996 Mitsubishi Galant

1 Answer

1999 Dodge Intrepid...shift lever wil shift gears


I believe that the cable has to be adjusted. Most cases, the cable adjustment is off. Worst case senario, is the bushing in tranny is worn out.

Jun 22, 2009 | 1994 Dodge Intrepid

1 Answer

1996 sl2 manual


sounds like a bent shift lever.

Aug 12, 2008 | 1996 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...