Question about 1999 Buick Park Avenue

Open Question

04 buick park avenue 3.8l how to set timing marks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 416 Answers

SOURCE: 1997 Buick Park Avenue

This is the diagram but you should have factory belt diagram sticker is still somewhere under the hood
If not:
http://www.mvreader.com/multiview/dayco/zoom.php?zoom_item=C0001D&l=n&catalog=auto&category=
To replace the serpentine belt on a V6 3800 you must jack up the motor and remove a motor mount. You must then use a breaker bar with a socket (13/64") and pull it toward the front of the car to release the belt tensioner. Put the new belt on, tighten it, put the mount back on, and lower the jack.
Driving without a belt can cause the motor to overheat, will cut power steering, and will not recharge the battery, so you should probably get a tow
Good Luck

Posted on Jan 08, 2009

  • 6 Answers

SOURCE: 1991 buick park avenue will not run fuel pump is good and replaced the fuel filter

http://www.fixya.com/cars/t1810766-1991_buick_park_avenue_stop_running

Check out this link. It may help you with your problem.

Posted on Apr 23, 2009

matney68
  • 426 Answers

SOURCE: Cannot change 3 rear spark plugs on 1999 Buick park avenue

there is a special tool for this job but I have cheated on this but you ned to be careful when doing this.The wishbone shaped mount on the front going from motor to front of vehicle, remove and it allows the motor to tilt.

Posted on Jun 19, 2009

  • 115 Answers

SOURCE: 2000 Buick Park Avenue Service engine soon light

need to take car somewhere to have the code read with a scanner,try parts stores first some will do it for free if not the dealers have them

Posted on Sep 15, 2009

ZJLimited
  • 17970 Answers

SOURCE: FUSE IDENTIFICATION FOR 97 BUICK PARK AVENUE

Several Fuse Panel locations there; all fuse's description can find it in 1997 Buick Park Avenue Owners Manual (page 331 and next).

Hope this help (remember comment and rated this post) TY for using Fixya.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have replace 4 coil packs in the last year and half. the car shut off as I am driving down the road and will not start back up. What would cause this?


Engine Stalling Due to Mass Air Flow/Crankshift Position ...

repairpal.com > Problems > Buick > Park Avenue
Buick Park Avenue Engine Stalling Due to Mass Air Flow/Crankshift Position Sensor ...engine shuts off when driving. ... The next two times it stop while driving it took longer to start, so i decided to ... 2000 Buick Park Avenue- 3.8L V6Visitor.

Sep 14, 2015 | 2000 Buick Park Avenue

1 Answer

How many quarts of oil is needed in a 2001 buick park avenue ultra


I looked the specification up but it was not listed as such.

I would add 5 quarts of oil in the buick park avenue ultra to start.
Then, I would check the dipstick and add until it hits the full mark.

This is what they would do at Walmart or Sears.

Good luck on this one.

Jul 06, 2010 | 2001 Buick Park Avenue

1 Answer

98 Buick Park Avenue (Turbo) P0717 fault code,


CODE PO717 IS - A/T INPUT SHAFT SPEED SENSOR LOW INPUT CONDITIONS.YOUR INPUT SHAFT SPEED SENSOR COULD BE DEFECTIVE.CHANGE FLUID + FILTER IF IT HAVE NOT BEEN CHANGED IN A LONG PERIOD OF TIME.

May 29, 2010 | 1998 Buick Park Avenue

1 Answer

Need get timing chain set righton chrysler 2.7 1999


Did you change engines or replace parts on your engine? If you changed engines with a year newer the cam gear is different and it will also run this way. If you didn't change engines I'll post the timing marks. You line the colored links up to the marks on the gears

Apr 24, 2010 | 2001 Buick Park Avenue

1 Answer

Buick park avenue engine start problem


Try replacing the coolant control temp sensor, the one to the computer (usually it will have two wires), not the sensor to the temp light or gauge (usually has only one wire).

Apr 20, 2010 | 1991 Buick Park Avenue

1 Answer

Cigarette lighters don't work on Buick 1992 Park Avenue


More than likely, it is close to the back of the lighter though it may be in the fuse box. It might be a sign for you that it is time to quit.

Since you know where the fuse box is but cannot id which fuse protects this circuit, I suggest you remove the fuses one at a time until you discover which, if any, fuse if burnt. A pair of needle nose pliers will make this job easy for you.

Mar 21, 2010 | 1992 Buick Park Avenue

1 Answer

Transmission gasket,how to do


make sure the pan is not warped by setting on flat surface w/the gasket side on the ground. don't over tighten spec is 8-12 inch lbs. not ft. lbs.

Oct 03, 2008 | 1989 Buick Park Avenue

Not finding what you are looking for?
1999 Buick Park Avenue Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...