Question about 2007 Chevrolet Silverado 1500 2WD

1 Answer

Why did my cruse control stop working after just a few miles

Cruse control DOES NOT WORK

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Is the Check Engine Light coming on?

Posted on Jun 16, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Benimur
  • 6966 Answers

SOURCE: 98 chevy k1500 cruse control

Hi,

Appreciate the "Ask Me".

To my knowledge, Cruise Control would be relatively difficult to diagnose without a scan tool attached to the control module to read the error codes. Additionally, car versions in my country seldom have such a device since our roads are narrower and travel distance is not that great.

Though most known causes are:

  • the connector to the module;
  • loose brake pedal/switch;
  • loose clutch pedal/switch (for manual transmission);
  • vacuum line to actuator (most likely), vacuum actuator, diaphragm, control valve.
Other possible components to check are:
  • the control module itself (bolted to the firewall);
  • control cable or linkage;
  • speedometer sensor;
  • steering wheel controls switches;
  • throttle position sensor.
As posted above, quite a number of possibilities. Any other indications, speedometer OK; abnormal throttle responses; abnormal idling, brake light always ON, slack in the accelerator/gas pedal? Was it cutting in/out before? Was there any recent repair work done on the engine before the cruise control cut out?

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Posted on Aug 04, 2008

  • 16 Answers

SOURCE: 2004 chev impala cruse control not working

if pulling up on the brake pedal worked, lets start there. I'm not sure on that specific car, but there should be a white switch on the brake pedal bar up under the dash that turns on the brake lights when you push the pedal. It would also turn of the cruise. those switches are adjustable. it should skrew in and out. if that is the problem, you've probably been driving around with the brake lights on all the time.

Posted on Jan 14, 2009

  • 155 Answers

SOURCE: my cruse control stop working were do i find the

its not your fuse its the combo switch

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to fix Cruise Control


The most common problem on this vehicle is the sensor right on the master brake cylinder the seal goes out and brake fluid gets right in the sensor ruining it that is the most common problem lete no if it helps

Sep 22, 2014 | 2001 Ford Windstar

1 Answer

Cruse control stop working while I was driving ... now it won't work


Hi, it sounds like you have a faulty pedal switch or the switch needs adjusting, on the brake and clutch pedal there are small switches that turn the cruse control off when the pedals are used, hope this helps

May 15, 2014 | Cars & Trucks

1 Answer

Horn doesnt work after re-pack of airbag


The horn, cruse control and air bag each get power from the clock spring and each have a wire plugged no to it. The horn wire is probably not connected. When the clock spring breaks the horn and cruse control stop working and the air bag light stays on.

Apr 21, 2014 | 2002 Chevrolet Monte Carlo

1 Answer

Cruse control stoped working is there a fuse out?


If your cruse is out, there few thing to ck such as fuses . brake switch operation & cruse switchs .If u have could use a dvom & ck these items for an open circuit or resistance . this may point to your issue . The dealer uses a consult3 that can scan these items fast and may show your issue in seconds .

May 12, 2013 | 2007 Nissan Sentra 2.0 SL Sedan

1 Answer

Cruse control stopped working.light comes on but cruse won't work


you need to wrap a zip tie around the throttle linkage and reconnect the cruise to the linkage

Jan 23, 2011 | 2005 Ford Taurus

1 Answer

Auto has 23K and cruse stopped working. checked


I had the same problem with my 2003 santa fe. Do you have any brake lights out in back? Weird as it is, as soon as I fixed a burned out brake bulb, my cruise worked again. The only relation I can think of is that tapping the breaks causes cruise to turn off - so maybe a broken brake/tail light passes a singal to cruise control from some reason???

Apr 07, 2009 | 2003 Hyundai Santa Fe

1 Answer

Speedometer, odometer, cruse control & tranny overstopped working


If it has antilock brakes, the sensor is on the top of the rear differential. This sensor usually drives the speedometer. check the sensor for an open in its windings and also the wire that connects to it for any breaks.

Mar 31, 2009 | 1994 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...