Question about 2006 SsangYong Rexton 270

Open Question

Belt fan tension - 2006 SsangYong Rexton 270

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car broke down due to fan belt and no tensioner bolt. Is the tensioner connected to the alternator


Yes the belt runs over the alternator, A/C etc. This page shows how it works, and the tensioner needs to keep tension on the belt to drive the pulleys including the alternator.

1994 Dodge Spirit Drive Belt Diagram Other Category Problem 1994

Sep 19, 2015 | 1991 Dodge Spirit

2 Answers

Need timing belt digram for a 2000 kia sportage


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Apr 17, 2013 | 2000 Daewoo Nubira

1 Answer

99 kia sporage timing marks


Hi there:



Check this information...

dfd3ea1.gif


Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif



  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)


  1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
  2. Timing Belt Installation


eb770f2.gif

  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Mar 14, 2012 | Kia Sportage Cars & Trucks

1 Answer

Problem with 99 kia


Hi there:Check this information...

dfd3ea1.gif


Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif



  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)


  1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
  2. Timing Belt Installation


eb770f2.gif

  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Mar 14, 2012 | Kia Sportage Cars & Trucks

1 Answer

Replacing fan belt?what tools are required?


Instructions

Things You'll Need
3/8-inch drive breaker bar
Metric sockets
Serpentine belt

1 Open the hood and inspect the flat surface on top of the plastic fan shroud for the belt routing diagram. Follow the diagram instructions to route the new belt.

2 Locate the serpentine belt self-adjusting tensioner on the front of the engine block. The tensioner has a pulley on the bottom of the tensioner arm, which the belt travels under. The tensioner can only be rotated from the bolt that secures the pulley to the tensioner arm.

3 Rotate the tensioner in a clockwise motion with a metric socket and the breaker bar to loosen the tension from the belt. Then, pull the belt off the top of the tensioner pulley. Release the tensioner pulley and pull the breaker bar off the pulley bolt.

4 Pull the belt out of the accessory pulleys. Then, slide the belt around each fan blade and out of the engine bay. Rotate each fan blade to the top side of the engine to get the belt around each fan blade.

5 Match both the new belt and the old belt together to make sure that the new belt is the correct size. Then, route the new belt around each fan blade and around the crankshaft pulley. The crankshaft pulley is the big pulley at the very bottom of the engine.

6 Follow the routing directions from the belt routing diagram to install the new belt around the other accessory pulleys. Once the belt has been routed around all of the pulleys, look over the belt and make sure that it is secure inside all of the pulleys.

7 Crank the 1998 Dodge Caravan and let the motor run for about 15 seconds. This will finish seating the ridges of the new belt into the grooves of each accessory pulley.

8 Shut the motor off and close the hood.

Jul 07, 2011 | 1998 Dodge Caravan

1 Answer

Fan belt fell off. Need a new belt tensioner. Is AC belt and fan belt on same tensioner


The A/C compressor has its own belt and tensioner. The alternator, p/s pump, and water pump use the other belt and tensioner. Make sure you check the A/C belt while you're digging around in there. If it is cracked replace it.

Sep 27, 2010 | 2001 Chevrolet Silverado 2500HD

2 Answers

Diagramm serpantine belt 2005 sprinter2500


Hi.

Here the belt routing for 2005 Dodge Sprinter 2005, whch was sold only with the 2.7 engine mounted:



feac688.jpg


Fig. Accessory Belt Routing-A/C Compressor (1), Power Steering Pump (2), Tensioner (3), Crankshaft Pulley (4), Water Pump (5), Alternator (6), Idler Pulley (7)-All Engines

Here a different view:

62bcecc.jpg

Here also the fan belt routing;

729c6e0.jpg

Fig. Fan belt routing-Fan pulley (1), Fan belt (2), Crankshaft pulley (3)-3.0L engine shown

PROCEDURE Removal & Installation


2.7L Engine

1. Loosen the tension adjust and remove the A/C compressor drive belt.
2. Attach a 3 / 8 inch drive ratchet to the automatic belt tensioner.
3. Rotate the belt tensioner counterclockwise to release the belt tension.
4. Remove the accessory drive belt, starting with the water pump pulley.



To install:

1. Position the accessory drive belt around every pulley except the water pump pulley.
2. Rotate the drive belt tensioner clockwise, install the accessory drive belt and release the tensioner.
3. Position the A/C Compressor drive belt over the crankshaft pulley and A/C compressor pulley.
4. Tighten the drive belt tensioner.
5. Ensure the belt is seated properly on all of the pulleys.

If this solution was helpful, then please do not forget to Accept.
Writing dedicate solution, sharing skills, researching and extracting info from service documents takes time, and your feedback is important for us.
If you repute any solution useful, please click on Accept.

All the best.

Ginko.

Sep 21, 2010 | Dodge Sprinter Cars & Trucks

2 Answers

Need diagram to put timingbelt on 2001 kia sportage


prev.gif next.gif Timing Belt Removal & Installation SOHC To Remove:
  1. Disconnect battery negative cable.
  2. Remove fresh air duct.
  3. Drain engine coolant into an appropriate container and retighten radiator drain plug.
  4. Remove upper radiator hose.
  5. Remove fan clutch assembly bolts.
  6. Remove 5 cooling fan shroud bolts.
  7. Remove fan shroud and fan as an assembly.
  8. Loosen alternator mounting bolts and remove drive belt from pulley.
  9. Remove fan pulley.
  10. Remove 4 cooling fan assembly bolts.
  11. Remove cooling fan assembly.
  12. Remove 4 bolts and upper timing belt cover.
  13. Remove 2 lower bolts and lower timing belt cover.
  14. Loosen adjusting bolt and remove A/C belt.
  15. Remove alternator belt.
  16. Loosen power steering pump lock bolt and mounting bolt.
  17. Remove drive belt from crankshaft damper. Camshaft timing marks kia-03-20-7032.gif

  18. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  19. Remove 5 bolts and remove damper.
  20. Remove timing belt guide from timing belt pulley.
  21. Loosen tensioner lock bolt.
  22. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt. NOTE: Mark the direction of timing belt rotation on the belt if it is being reused.
  23. Remove timing belt.
To Install:
Timing belt pulley timing marks kia-03-20-7035.gif

NOTE: Timing belt pulley timing mark and timing mark must be aligned.
Camshaft timing marks kia-03-20-7032.gif

NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
Timing belt installation kia-03-20-7036.gif

  1. Install timing belt with minimal slack from timing belt pulley to water pump and from water pump to camshaft pulley.
  2. Loosen tensioner lock bolt until tension is applied to timing belt. CAUTION
    Do not turn crankshaft counterclockwise.
  3. Turn crankshaft pulley 2 full turns clockwise and ensure timing marks are properly aligned.
  4. Tighten tensioner lock bolt to 33 ft lb (45 Nm).
  5. Apply a force of 21 lb to timing belt midway between idler pulley and camshaft pulley.
    • Deflection should measure 0.43-0.51 inch (11-13 mm)
    NOTE: if timing belt deflection is incorrect remove timing belt and install NEW tensioner spring.
  6. Install timing belt guide.
  7. Install crankshaft damper pulley.
  8. Install 5 crankshaft damper pulley bolts. Tighten bolts to 132 in lb (15 Nm).
  9. Install power steering pump drive belt.
  10. Adjust power steering pump drive belt tension and tighten lock bolt and mounting bolt.
  11. Install alternator drive belt.
  12. Install A/C drive belt.
  13. Install lower timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
  14. Install upper timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
  15. Install cooling fan assembly and 4 bolts. Tighten bolts to 27 ft lb (37 Nm).
  16. Install fan pulley.
  17. Install fan clutch and shroud as an assembly. Tighten bolts to 74 in lb (8 Nm).
  18. Tighten 4 cooling fan nuts to 16 ft lb (22 Nm).
  19. Adjust alternator belt tension and tighten alternator mounting bolts.
  20. Install upper radiator hose.
  21. Install fresh air duct.
  22. Connect battery negative cable.
  23. Refill/bleed cooling system.
DOHC To Remove:
  1. Disconnect battery negative cable.
  2. Remove fresh air duct.
  3. Remove 5 cooling fan shroud bolts and 4 thermo-modulated fan nuts.
  4. Remove 4 thermo-modulated fan shroud fasteners.
  5. Remove generator drive belt.
  6. Remove fan pulley (located above crankshaft pulley).
  7. Remove 4 bolts and splash shield (located under front of vehicle).
  8. Remove A/C drive belt and power steering drive belt. Timing Belt Removal kia-03-20-7097.gif

  9. Remove 5 bolts and upper timing belt cover.
  10. Remove 2 bolts and lower timing belt cover.
  11. Loosen tensioner lock bolt and pivot tensioner pulley outboard.
  12. Retighten tensioner lock bolt. NOTE: Mark timing belt for rotation if it is being reused.
  13. Remove timing belt.
To Install:
Crankshaft match marks 79245g25.gif

  1. Align marks on timing belt pulley and pump body. Camshaft pulley alignment marks 79245g28.gif

  2. Align marks on camshaft pulleys with alignment marks on seal plate.
  3. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  4. Loosen tensioner lock bolt.
  5. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  6. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  7. Apply a force of 22 lbs to timing belt between camshaft sprockets.
    • Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
    NOTE: Replace tensioner spring if timing belt deflection is excessive.
    Timing Belt Installation kia-03-20-7097.gif

  8. Install lower timing belt cover.
  9. Install upper timing belt cover.
  10. Install power steering drive belt and adjust belt tension.
  11. Install fan pulley.
  12. Install generator drive belt and adjust belt tension.
  13. Install A/C drive belt and adjust belt tension.
  14. Install splash guard.
  15. Install fan and fan shroud.
  16. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  17. Install fan shroud mounting bolts.
  18. Install fresh air duct.
  19. Connect hose to resonance chamber.
  20. Connect battery negative cable.

Aug 02, 2010 | 2001 Kia Sportage

1 Answer

How replace the fan belt and idler pully


Your Catera does not have a fan belt, it has an accessory belt. The fan is electrically operated using a thermal switch.

To replace the accessory belt, you use a ratchet head to loosen the tensioner pulley, and slide the belt off one pulley, then release the tensioner and finish removing the belt. You install the new belt on all but the pulley closest to the tensioner, release the tension with a ratchet head, then install the belt on the tensioner pulley and release the tensioner so that it applies pressure on the belt.

Dec 27, 2009 | 1998 Cadillac Catera

3 Answers

1999 kia sportage timing marks


dfd3ea1.gif Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif
  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
  8. NOTE: Replace tensioner spring if timing belt deflection is excessive.
Timing Belt Installation


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Jul 26, 2009 | 1999 Kia Sportage

Not finding what you are looking for?
2006 SsangYong Rexton 270 Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top SsangYong Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

terry stevens

Level 3 Expert

991 Answers

Are you a SsangYong Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...