Question about 2006 Infiniti G35

Open Question

Air blend door actuator disconnect - 2006 Infiniti G35

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

1 Answer

How do i fix a stuck blend door on 2010 dodge nitro?


I would pull off the blend door actuator and swap it out with a new one. Or another option is to swap it out with one of the other actuators. The blend door actuator is interchangeable with the actuators for the mode-air doors and the recirculation-air door.

Disconnect and isolate the negative battery cable.

If equipped, remove the silencer from below the driver side of the instrument panel.

Disconnect the wire harness connector from the blend door actuator located on the driver side of the air distribution housing.

Remove the two screws that secure the blend door actuator to the actuator mounting bracket and remove the actuator

Feb 17, 2015 | 2010 Dodge Nitro

3 Answers

Driver side blowing hot air passenger side blowing cold air


I'm having the same problem except on mine it's the driver's side that's blowing cold. Do you have the pictures in a finer resolution? I can't make them out and when I zoom, they are too grainy. Does the replacement require removing the dashboard? What's the general cost of the acuators? Are they readily available at like NAPA or other parts stores?

Nov 26, 2011 | 2006 Kia Amanti

1 Answer

My 2004 Avalanche ' heating system will not heat. No matter what the setting it either blows no air or cold air and it is 25 degrees outside so this is a problem. The engine is up to temp and I have tried...


The most likely cause is a failed blend door actuator; however I recommend a little troubleshooting. First, can you hear a clicking sound behind the dash when you turn the setting to hot? If yes, it is certainly the actuator stripping its gears. If not, check to make sure the heater hoses are both hot as they connect to the heater core at the firewall (in the engine compartment). If one or both of the hoses do not get hot, there is a blockage caused either by an air bubble or a stuck water control valve in the heater hose. If the hoses are both hot, the indication is again the blend door actuator.

Below are instructions for replacing the actuator. Look at the diagrams carefully--the big arrows point to the front of the truck and the actuator is on the side of the heater box above the outlet duct that runs to the driver's side of the floor. Also, the actuator is expensive, so I recommend you make sure it's bad and shop around a bit to get a good price. To check out the actuator, first see if you can turn the blend door by hand. If you can't turn it, maybe it's jammed. Also, reconnect the actuator after removing it and see what it does when you turn the heater to hot.

Removal & Installation
  1. Remove the floor air outlet duct extension (1) from the floor duct (2).

    jturcotte_393.gif

Fig. Remove the floor air outlet duct extension (1) from the floor duct (2)


Disconnect the electrical connection at the blend door actuator (#10 in pic below). jturcotte_394.gif

Fig. Blend door actuator and related components


Remove the blend door actuator mounting screws from the HVAC module.


Remove the blend door actuator as an assembly with the actuator cam.
jturcotte_396.gif

Fig. Remove the blend door actuator mounting screws from the HVAC module



To install:

  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam

  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).

  3. Connect the electrical connection at the blend door actuator (10).
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).


Picture of actuator:


jturcotte_57.jpg

Dec 07, 2010 | 2004 Chevrolet Avalanche

2 Answers

Heater blows cold air


Hi!
If the Temp. Selector Control is set to Heat and blows cold air, your Blend Door Actuator may be stuck or it is inoperative. The actuator is not fixable, if it fails, it must be replaced. Follow the instructions to remove and replace it.
  1. Disconnect battery negative cable from battery and properly isolate to prevent accidental reconnection.
  2. Remove the instrument panel.
  3. Disconnect the electrical connector from the blend door motor/actuator.
  4. Remove the four screws holding the blend door actuator to the plenum.
  5. Remove the temperature blend door actuator.
BLEND DOOR ACTUATOR CONNECTOR e8349ea.jpg

BLEND DOOR FASTENING SCREWS 9744710.jpg

Show your appreciation with a - 4 THUMBS - rating for answering your FREE question. Thank you for using FixYa.

Oct 07, 2010 | 2003 Mercury Grand Marquis

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

2 Answers

Air conditioner blowing hot air


Blowing hot air when set to A/C is almost always a stuck blend door, dead blend door actuator, or a cracked or disconnected blend door actuator vacuum line. The blend door is inside the a/c ducting under the dash, but the actuator will be accessible outside the ducting.

Jul 05, 2010 | 2000 Lincoln LS

1 Answer

My heater will only blow hot air out of the rear vents from the rear controls. The front vents only blow cold air. Is there a simple fix?


blend door or temp contrl switch is bad.

Section 12-02: Heating and Defrosting 1998 Windstar Workshop Manual
REMOVAL AND INSTALLATION Actuator Motors, Electric Temperature Blend Door
Removal
  1. Remove cassette storage box or center shelf unit, if equipped.
  1. Remove instrument panel ash receptacle (04810) by depressing service lever.
  1. Disconnect electrical harness connector from electric blend door actuator.


    sww~us~en~file=am0101a.gif~gen~ref.gif

  1. Remove three retaining screws.


    sww~us~en~file=am0100a.gif~gen~ref.gif

  1. Carefully pull electric blend door actuator outward and off A/C evaporator housing (19850) assembly.
Installation
  1. Follow removal procedure in reverse order.
  1. Air temperature control door shaft is keyed. Move door to properly insert electronic actuator shaft. Make sure the shaft is completely in and properly seated.

Jan 14, 2010 | Ford Windstar Cars & Trucks

2 Answers

200 Jeep Laredo..Air is cold and fan is blowing,


there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.
7d2da02.gif
  1. Disconnect and isolate the negative battery cable.
  2. Remove the glove box from the instrument panel.
  3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
  4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
  5. Remove the blend door actuator from the vehicle
to instal
  1. Position the blend door actuator into the vehicle.
  2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
  3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
  4. Connect the HVAC wire harness connector to the blend door actuator.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable.

Sep 09, 2009 | 1998 Cadillac Seville

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14184 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...