Question about 2004 BMW 525i Touring

Open Question

WHERE IS AUC SENSOR 2004 BMW 5 SERIES 2.5 L?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: How do you reset the service lights on 2004 BMW Series 5 330TDi

You should not have the 20-pin DLC connector in your car so you only need to hold the left odometer reset button while turning the ignition key to position 1 (Accessory). Keep holding the button for 5 or so seconds until any of the following shows in the display: OIL SERVICE or INSPECTION with RESET or RE. Release the button and press it again for another 5 or so seconds until RESET or RE flash. While the display flashes, press the button one more time briefly. If done correctly, END SIA should show up for a few seconds.
This should sort your problem!

Posted on Dec 19, 2008

Ad
  • 90 Answers

SOURCE: bmw 5 series 96 starter misses engagment

MISSES HOW EXACTLY?
IF IT CLICKS THEN ITS LACK OF POWER FROM THE BATTERY OR IF IT SPINS OUT FREELY THEN ITS THE STARTER MOTOR

Posted on Mar 15, 2009

  • 39 Answers

SOURCE: Bmw 2004 Tailgate lights

is this an X5? is so most likely it is the contact points on the bulb itself take a flash light and look inside the tail light assembly at all the contact points of the affected bulbs

Posted on Mar 31, 2009

  • 121 Answers

SOURCE: i am about to purchase a bmw 2004 525i but cannot

if you see a blue tooth sign it will have blue tooth, best to fine out from a main dealer

Posted on Jun 05, 2009

  • 41 Answers

SOURCE: how to change the headlight on a 2004 bmw 5 series

if you have an entire headlight assembly (in case of accident) remove bumper, there are 8mm screws on the inner lining of the fron wheel well where the fender plastics and the air dam connect to the bumper, undo the screws concerning the bumper on bot sides of the car. then remove the plastic cover under the bumper (either philips screw heads or 10mm) and then under the aluminum re-enforcement strip behind the bumper (access from under the car) remove the torx screws that hold the bumper aluminum to the car frame, get a friend to help you pull the bumper off evenly an then seek the 8mm screws that hold the headlamp in place. the headlamp comes off the car strait out the direction of the front. disconnect the wires and connect the new lamp and fasten to the car. then do the assempbly in reverse order for the bumper installation.
for just changing the bulb, there are some rubber seals behind the light where the bulb rests. there are metal clips than you depress to release the bulb. install a new bulb and then replace the rubber caps.

Posted on Nov 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My BMW is in limp mode


year model and engine code will help

Jul 27, 2016 | 2007 BMW 320i E90

1 Answer

How to program "Welcome ligths" on bmw e60 2004?


Well Get Your Manual Book on the Page Setup Program Utility and Follow the instrution... Under Your Dash You Got what they Call The Terminal Box Connection For Computer Analyzer But off corse To do So .. You must bring your Car on The BMW Deeler To
Activate The Rom Memory Utility.. To Re-program your Light sensor What you call Welcome Lights On your risk Pin 2.8.13. must be short respectively with a diode 2 and 8 13 for ground. on your ignition If you miss it will just cost you S750 dollards for new computer Dash... So dont do it.. Try to re-program your Key Tranceiver some time they work Good luck

Sep 22, 2010 | 2004 BMW 5 Series

1 Answer

Brake change reset on 2004 BMW 525I sedan


some you can reset just by replacing the brake sensors, others you need a scanner.

Jul 06, 2010 | 2004 BMW 5 Series

1 Answer

My 2004 bmw 525i wont start or crank although the battery has full power


won't crank????? Starter motor probably. Crank but won't run...fuel pump, crank sensor, coil pack and/or computer.
could also be the relay sending full juice to the starter motor.

Apr 23, 2010 | 2004 BMW 5 Series

1 Answer

I have fault code EGS (054) 36 Gear monitoring 4, BMW X5 E53 3,0 D 2002


2003 X5 bmw the trans. fail safe program comes on when driving, I was told that the trans needs to clean out and put new sensors. Is that true it gives the code 055

Apr 09, 2010 | 2004 BMW 5 Series

3 Answers

Where is the abs speed sensor on a 5 series bmw?as the abs light and traction light have both illuminated


You have 4 wheel speed sensors. There is one at each wheel located just behind the hub. You can trace it by loacting the black insulated wire leading out from the wheel well and going behind the wheel.

Mar 27, 2010 | 2001 BMW 5 Series

1 Answer

What is the location ofttgen sensor, bank 2


Its located in the exhaust manifold on the passenger side,its the sensor closest to the rear of the engine.

Feb 07, 2010 | 2004 BMW 3 Series

2 Answers

X5 wont start


check the map sensor and the idle speed sensor. check the fuel pressure at the engine. check all fuse and relay for proper operation

Jul 31, 2009 | 2004 BMW 5 Series

Not finding what you are looking for?
2004 BMW 525i Touring Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...