Question about 2006 Pontiac Montana

Open Question

How to instal a knock sensor on a 2006 pontic montana sv6

Is there a certain position or way to tighten the new sensor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: 2005 Pontiac SV6 Montana key fob unlocks doors but will not lock

For the sliding doors you need to clean the contacts, there are 6 or 8 on both sides, just wipe them clean as they are probably covered in oil/grease/grime.

Posted on Feb 14, 2009

Ad
  • 1 Answer

SOURCE: clunking from front end

CHECK FRONT STABILIZER LINK KITS FOR PLAY.
ONE ON EACH SIDE ATTACHED TO STRUTS.

Posted on Apr 26, 2009

fingaz22
  • 1068 Answers

SOURCE: Changing the front brake pads on a 2006 Pontiac Montana SV6

no that is only the older rear calipers on gm and others. the fronts do not have that style caliper and sound like the calipers are frozen and may be way your changing the pads. try opening the bleeder screw and then compressing them if they go then you need need brake hoses and if not you need calipers. god luck man

Posted on Dec 13, 2009

  • 32 Answers

SOURCE: Where is the fuse box for a 2006 Pontiac Montana

on the driver side under the dash or the side by the door jam

Posted on Apr 02, 2010

  • 5 Answers

SOURCE: 2006 Pontiac montana SV6 power sliding door sensor

I have a 2006 SV6 with the power sliding doors. The problem that I found was with the contacts on the door ( They are called plungers) the movable pins were losing connection with the fixed part The plunger is very easy to replace if you can find one. The plungers are covered with a rubber cover and is held in place with 2 plastic pins. My Pontiac dealer could not even find one in his books or even a picture of one, and claimed that he had never had anyone come with a door problem. My Chevy dealer said that it came with a wiring harness that is not needed for $154. The cure that I came up with was to take the plunger block apart (it snaps together)and replace the rusted out springs then solder 3" wires to the end of the plunger pins (they solder easy) to the tabs that go to the plug(pop out the tabs or you will melt the plastic. It took about 45 min. now the doors work like new and will never loose contact again

Posted on Aug 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 PONTIAC MONTANA FUSE BOX DIAGRAM


On this website you find fuse box diagram for Pontiac Montana SV6 2005 - 2006

Pontiac Montana SV6 2005 2006 fuse box diagram Auto Genius

Mar 02, 2013 | 2006 Pontiac Montana SV6

1 Answer

Where 2005 Pontiac Montana SV6 heater fuse in the box


On this website (link below) you find fuse box diagram and description for Pontiac Montana Sv6 (2005 - 2006)

Pontiac Montana SV6 2005 2006 fuse box diagram Auto Genius

Feb 01, 2013 | Pontiac Montana SV6 Cars & Trucks

2 Answers

I have a 06 montana the rear wiper not working but it only works when i push on the arm so i check and tight the arm but it till doing the samething what could it be


Wiper shaft is stuck by rust (aluminium oxide). Remove wiper motor. Knock out wiper shaft with soft hammer. Clean shaft hole with similar size drill bit.

Mar 14, 2010 | 2006 Pontiac Montana SV6

1 Answer

How to install brakes on 2006 montan sv6


Dear Stray Shims.........these shims that came along with the new brake pads are designed to be installed on the non friction side of the brake pad(the side that does not rub up against the rotor). These are designed to absorb a little runout so that you can have a better pedal. When you install these shims make sure to install them with brake temp approved adhesive so they don't shift and start rubbing against the rotor. Most shims are shipped with adhesive already on them though. If you have any other questions you're more than welcome to get back to me.....THX and I HOPE I COULD HELP!!!

Nov 17, 2009 | 2006 Pontiac Montana SV6

1 Answer

Rear wiper won't work


I have a 2006 Montana. Mine was seized. I fixed it by knocking the shaft out of the motor gear socket with a piece of wood with hammer, cleaned the hole with a drill and it worked.

Nov 17, 2009 | 2006 Pontiac Montana SV6

1 Answer

No clunking until replaced front end brake pads and rotors. Pontiac Montana 2002 not a FWD. I'm not 100% sure but I also believe I can feel a vibration on steering wheel coming from front.


1. Have the caliper checked if the retaining bolts are fully tightened and all shims and pins are properly installed. 2. Was your rotors resurfaced??If not, The new pads are flat(new), and the rotor might be uneven causing the pads to vibrate. 3. If they aren't the rotors, inspect the CV shafts for tightening, or damage. Hopefully this helps

Jul 28, 2009 | 2006 Pontiac Montana SV6

1 Answer

Clunking from front end


CHECK FRONT STABILIZER LINK KITS FOR PLAY.
ONE ON EACH SIDE ATTACHED TO STRUTS.

Mar 22, 2009 | 2006 Pontiac Montana SV6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...