Question about 1997 Volkswagen Jetta
Timing Belts are actually easy to change....... IF you take extra EXTRA care when replacing to have ALL the pointers lined up..... I am not sure about the VW... but I have done a few over the years.... Toyota mainly....... but if you have not done a Timing Belt before I strongly recommend you go to a Mechanic to have it done............. You just need to be ONE TOOTH out and it is a new engine.......
Posted on May 08, 2014
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Hello, VW polos 1.0, 1.4. 1.6, suffer from carbon bulid up in the throttle bodys causing bad idling, esp the Bosch Mono-Motronic (Throttle Body Injection systems), a good clean with carb cleaner should repair the problem, also engine temp sensor replacement and idle speed control valve replacement can help idle problems.
Posted on Apr 19, 2009
the cover just pulls off and disconnect breather hose as u lift it.there is about 15 screws to remove then the cover opens
Posted on Jul 12, 2009
I have changed a few cylinder heads under warranty for this type of problem. The exhaust valve guides wear, this causes the exhaust valve to seat badly, giving low compression. if one cylinder compresion reading is more than about 50 psi below the others, then this warrants head removal. It is quite a job, due to the fact that the camshft id chain driven. If you are up for it then once the head is removed, poor liquid into the exhaust ports and see if it leaks out through any of the exhaust valves.
Posted on Jul 23, 2009
SOURCE: Removing VW polo 2005 battery?
Removing a battery from a Beetle is a bit complex and tricky. I just changed the battery in a 2003 2.0 Beetle. However, the process is very similar in a TDI Beetle. You will need more than your standard generic tool set in order to complete this task. Your tool list needs to consist of a pair of pliers (prefer locking type), a # 20 TORX head screwdriver (You will also need this if you ever plan on changing the Beetle's internal dash pollen filter for the A/C. ), a 10 mm and 13 mm sockets, a long extension and a wobble or universal to allow flexibility in tight spaces, an allen socket for removing the power steering reservoir, and a small adjustable wrench or a 10mm to remove the battery cables. If you are changing the battery you might as well buy a new Air filter since you will need to remove the air box in order to replace the battery. If you do change the air filter you will need a phillips head screwdriver.
1. Pop the hood.
2. Remove the two 10 mm bolts that hold down the air filter box.
3. Undo the clamp that holds the large tubing to the air box using your pliers. Move the tubing away from the box.
4. Unclip hose attached to the back of the air box near the large hose (under it).
5. remove the small breather hose from the air box.
6. Pull air box up and out.
7. Remove snap on cover from top of battery.
8. Remove small snap on wiring cover from back of the battery covering.
9. Unbolt power steering reservoir (next to battery case).
10. Disconnect the battery cables. Positive side first.
11. Remove the 13 mm bolt at the base of the battery along with the hold down clamp.
12. Pull the top wiring away from the battery case and then slide the battery towards the engine.
13. Remove the plastic battery case.
14. Remove the battery
Posted on Oct 07, 2009
Crankshaft sensor is located on the right side of the cylinder block behind or under the starter. It is fitted into the rear crankshaft oil seal hausing
Posted on Sep 12, 2010
Tips for a great answer:
Oct 08, 2015 | Cars & Trucks
Jan 10, 2018 | 1995 Volkswagen Polo 1.4
Jun 28, 2010 | 2000 Ford Focus
Aug 20, 2009 | 1997 Volkswagen Golf
95 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: