Question about 2007 Jeep Commander 4.7

1 Answer

How do I remove/replace driver door wiring harness from my 2007 jeep commander?

How do I disconnect the wiring harness from the body to bring it through the boot and out the speaker hole in the door?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

I dont know the specifics of your Jeep but on most cars there are alot of harness connector plugs behind the plastic kick panels under the dash-ahead of the doors

Posted on May 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

scoobystevey
  • 25 Answers

SOURCE: Replacing 1993 Jeep Grand Cherokee wiring harness in driver's door

watch the vaccuum lines very carefully. they are hell to track down and replace. other than that, just make sure you get everything correct. jeeps freak out when you screw up even just 1

Posted on Oct 22, 2008

  • 1 Answer

SOURCE: 2004 Jeep Grand Cherokee driver side power windows do not work

I had the same problem with now power to windows, mirrors and seat. The common soulution is the orange and or black wire in the boot have broken between the door and post.

Posted on Dec 07, 2008

  • 6982 Answers

SOURCE: 1995 Jeep Grand Cherokee power window wire broken

Your best way in is through the kick panel on the side. I generally solder an additional length of wire on and before connecting to other end, slide a piece of thin tubing (like washer fluid line) over it. After soldering the other end, slide the tubing over the repair and put a dab of silicone or other glue on the wire just before you have it all the way in position. Doing this protects the repair and the wire from further failure.Make sure you secure any extra wire inside the door where the window regulator won't grab it and tear it out.

Posted on Aug 31, 2009

BCally1
  • 133 Answers

SOURCE: 2007 jeep commander rocky mountain no sound from radio

take it to the dealer. they will put a new radio in it if you have under 36000 miles

Posted on Sep 12, 2009

  • 1986 Answers

SOURCE: replace exterior door handle on a jeep commander

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door

Posted on Oct 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disconnect a BCM in a chevy colorado 2007


Removal Procedure
Important:
• The ignition switch should be in the OFF position when connecting or disconnecting the connectors to the body control module (BCM).
• Always disconnect the black body wiring harness connector FIRST and the gray instrument panel (I/P) wiring harness connector LAST.
• Always connect the black body wiring harness connector FIRST and the gray I/P wiring harness LAST.
• Do not open the BCM housing. The module does not have any serviceable components. The module may be replaced only as an assembly.
Ensure the ignition switch is in the OFF position.
Remove the right front hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Right Side .
Disconnect the body wiring harness electrical connector (1) from the BCM.
Release the fastener retaining the body wiring harness electrical connector to the BCM. Remove the 2 fasteners retaining the BCM to the hinge pillar.
Remove the BCM from the hinge pillar by unlocking the integral tab.
Remove the BCM from the vehicle.
If installing a replacement BCM, program the BCM. Refer to Control Module References .

Dec 19, 2016 | Cars & Trucks

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

Jeep wrangler 2007 door hinges


I have removed the doors on my 2007 JKL several times and there is only the retaining nut, and grease in there. That's it.
Maybe there is no grease left in there?
Try spraying WD40 into the hinge over a few days, then disconnecting the electrical harness for the door, then remove the retaining nut from the bottom. Then get a muscular friend or a floor jack and piece of wood to slowly lift the door out of the hinge. Grease it well before you re-install the door. Reconnect wiring.

May 22, 2012 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

Remove and replace drivers door 1999 taurus?


Please don't forget to rate! Thank you!

Removal & Installation
c17hydro_32.gif

The door-to-body mounting



c17hydro_33.gif

Detach the door wiring from the connector


This is a two person operation.

  1. Remove the two door check-to-body retaining screws.

WARNING

Cover the end of the check strap to prevent possible paint damage.


  1. On the rear doors, remove the rear door trim panel, detach the electrical connectors from the components (if equipped) and remove the wiring harness from rear door.
  2. On the driver's side front door, disconnect the window regulator wiring, if so equipped, by removing the wire connector cover, loosening the screw and separating the connector halves.
  3. On the passenger side front door, remove the rubber harness protector from the body to reveal the electrical connectors. Detach the two electrical connectors.
  4. If the door is to be replaced, transfer the following components to the new door if in usable condition:
    • Door trim panel
    • Watershield
    • Outside mouldings
    • Trim clips
    • Window regulator
    • Door latch components.
  5. Remove the hinge retaining screws and nuts from the door and remove the door.

To install:

  1. Position the door onto the hinges and hand tighten the screws.
  2. Align the door and tighten the screws to 19-25 ft. lbs. (25-35 Nm).
  3. If removed, install the wiring harness to the rear doors.
  4. Attach the electrical connectors to the door panel.
  5. Install the door panel(s).
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 31; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Nov 20, 2010 | 1999 Ford Taurus

2 Answers

How do you remove the driver side door panel on a 2004 Jeep Cherokee.


- Remove trim plug from mirror flag bezel.
- Remove screws attaching trim panel to door
- Using a trim remover, detach trim panel perimeter push-in fasteners from door trim panel
- Lift trim panel upward and separate from door.
- If equipped, disconnect harness connectors for power accesories.
- Disconnect latch rods from inside handle actuator
- Finally, separate trim panel from vehicle.

I suggest check all information in the WJ Repair Manual Section 23 Body with graphics and other details.

Good luck (remember rated this help).


Feb 03, 2010 | Jeep Grand Cherokee Cars & Trucks

2 Answers

How to find fuse for a 2006 chevy equinox driver's power window


power windows are not usually fused. They have a circuit breaker that controls all the windows. So if only one window is not working it is something like a bad switch or window motor. Remove the door panel and unplug the connector to the window motor and check for power and ground when activating the switch.

Jan 02, 2010 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Drivers side door hinge replace


If your vehicle is equipped with power windows and locks, remove door trim panel.
- Disconnect power windows regulator, power lock motor and all other wire harness connections.
- Mark an outline around door hinges for installation alignement reference.
- Remove door hinge covers, retaining bolts, plates and shims. Remove door from vehicle.

For details and graphics, you can refer to the ZJ Repair Manual Secc-23-Body-Components (page 16).

I really hope helped with this; remember rated this help. Good luck.

Nov 26, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Replacing heater core on 2000 durango


  1. Disconnect the negative battery cable.CAUTION
    After disconnecting the negative battery cable, wait 2 minutes for the driver's/passenger's air bag system capacitor to discharge before attempting to do any work around the steering column or instrument

  2. Remove the instrument panel by performing the following procedure:
    1. Remove the trim from the right and left door sills.
    2. Remove the trim from the right and left cowl side inner panels.
    3. Remove the steering column opening cover from the instrument panel.
    4. Remove the 2 hood latch release handle-to-instrument panel lower reinforcement screws and lower the release handle to the floor.
    5. Disconnect the driver's side air bag module wire harness connector.
    6. If equipped, disconnect the overdrive lockout switch harness connector.
    7. Do not disassemble the steering column but remove the assembly from the vehicle.
    8. From under the driver's side of the instrument panel, disconnect or remove the following items:
      • The screw from the center of the headlight/dash-to-instrument panel bulkhead wire harness connector and disconnect the connector.
      • The 2 body wire harness connectors from the 2 instrument panel wire harness connector that secure the outboard side of the instrument panel bulkhead connector.
      • The 3 wire harness connectors from the 3 junction block connector receptacles located closest to the dash panel; 1 from the body wire harness and 2 from the headlight/dash wire harness.
      • The plastic park brake release linkage rod-to-rear parking brake release handle lever. Disengage the linkage rod from the handle lever.
      • The stoplight switch connector.
      • The vacuum harness connector from the left side of the heater/air conditioning housing assembly.
    9. Remove the instrument panel center support bracket.
    10. Remove the instrument panel wire harness ground screw located on the left side of the air bag control module (ACM) mount on the floor panel transmission tunnel.

Nov 08, 2009 | 2000 Dodge Durango

3 Answers

2004 grand cherokee jeep power windows and


Check for a 40 amp blown fuse for the BCM this controls those 2 unit. If this checks ok disconnect the BCM module and plug back in this will reset it the BCM is located under the Drivers side kick panel against the firewall. If it work after the BCM reset replace the BCM it will work only temporaraly.

Aug 29, 2009 | 2004 Jeep Grand Cherokee

1 Answer

How to remove rear light cover to change bulb


298002.jpg 1. Disconnect and isolate the battery negative cable. 2. Open the liftgate to access and remove the two push-pins (3) that secure the rear lamp unit (1) to the side jamb (2) of the liftgate opening. 3. Pull the outboard side of the rear lamp unit rearward far enough to unsnap the two ball studs on the outboard side of the lamp housing from the two plastic grommets (6) in the quarter outer panel. 4. Pull the lamp away from the vehicle far enough to access and disengage the retainer on the body wire harness (4) from the tab on the lower lamp housing. 5. Disconnect the body wire harness connector from the pigtail wire connector (5) on the back of the lamp housing. 6. Remove the lamp from the lamp opening of the quarter outer panel.
Hope this helps.

Mar 26, 2009 | 2007 Jeep Commander Rocky Mountain

Not finding what you are looking for?
2007 Jeep Commander 4.7 Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...