Question about 2006 Chrysler Town & Country

Open Question

Where is the wiring connector for the center console on a 2006 town and country?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2006 town and country passanger sliding door problem

I've leased two Town and Country vans over the past 4 years, and actually purchased the latest one after the lease. In both vans the sliding doors, normally the drivers side, reacted teh same way. If the door was closed it would open, stop a one point, and then return to the open position. At times I could get it close. But over time the doors stoped working all together.

It is not due to the switch or the motor. Most cases like this (in in both of mine) it is due to the repetitive use of that door, and the realitive inflexibility of the wire harness. Over time, and with more uses (in my case the driver side sliding door was used alot) the wire in the harness fails. Picture it as a willow branch. One snapped off of a tree it first is green and flexible, and bends pretty well into any form. But over time, with age and repetitive bending, it will break.

The only recourse is a new harness, as the wire/wires are broken somewhere in the harness (the belt chain in the lower track of the door). I was temped to take it apart and try to repair it myself, but as the parts were under warranty (I have the extended 85,000 mile), I opted to have the professionals handle it. The repair without the warranty is under $200 typically (parts and labor). Good luck.

Posted on Oct 09, 2008

polarcycle
  • 1392 Answers

SOURCE: Whirring sound after long drives 2006 Chrysler Town & Country

It is your power steering pump. The solution is to replace the P/S fluid resevoir and fill or flush the system.

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: fuse for stereo/cd in chrysler town and country minivan

Its in the box next to the battery and i had the same problem.The fuse is on the first line top.

Thanks

Posted on Mar 08, 2009

  • 85 Answers

SOURCE: Map light replacement on 2006 Town and Country?

Jun 17, 2009- ok I just looked at it. it is simple.
the lens pivots and presses a switch in on one end to make the light come on. take a butter knife or very small screw driver and reach in between the lens and the black center console. there you will CAREFULLY press a flat tab to the side that is made onto the lens ( I hope you dont break this tab).
on the very opposite position on the clear lens towards the door is where the lens has a tab that has a small hole in it. there is a plastic pin made onto the console trim that fits into this hole so the lens will pivot. this will give you an idea of which direction to pull the lens when you press in the tab,. it does look like it would break easily. I havent had to take mine off yet thankfully.
please visit again and rank this answer if this helps!... good luck

Posted on Jun 17, 2009

  • 7 Answers

SOURCE: Power door lock on pass sliding door not working

I just had mine fixed at the dealer for the same problem. Their first response to me was "this happens ALL THE TIME". He said there is a little plastic pin in the door handle assembly and the pin has been known to slip out of the assembly. However, when they got inside, they said it was the actual door handle (inside) that was broken and had to replace the whole piece. So, the first step according to my dealer/servicer would be to check for the little plastic pin.

Posted on Jul 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how to install an after market radio in a 1997 town and country lx


Go to Best Buy Or Pap Boys and Buy an Aftermarket install kit and A direct fit harness! Very easy to remove center bezal:
  1. Remove screw access cover.
  2. Remove the attaching screws holding bottom of the bezel to instrument panel.
  3. Remove the attaching screws holding top of the bezel to the instrument panel.
  4. Remove the bezel from the instrument panel.
  5. Disconnect the wire connector from back of the rear blower switch, if equipped.
  6. Disconnect the wire connector from the back of the HVAC Control.
  7. Remove the bezel.

Dec 23, 2014 | 1997 Chrysler Town & Country

1 Answer

Passenger light want come on when i first turn on the lights a2006 town and country van


Low beam circuit is open some where,acquire a wire diagram to trace to the source,could be at the connector at the bulb easiest to check there first for ground and power to each of the wires with a test light with lights on dim then on high beam to determine which wire is low beam circuit,ground always is the black wire.

Dec 14, 2014 | 2006 Chrysler Town and Country

1 Answer

My 2005 town and country driver side will only open manually. It wont open with the remote or with the button on the overhead console.


Bad fuse.Bad link on the wires betwen the door and the car is a removable link (electrical window/mirror,car speaker also connected...subject to fail).Ultimate,bad servo motor or bad controller board.Wish you luck.

Oct 21, 2013 | 2006 Chrysler Town & Country

1 Answer

We just replaced the EGR valve on our Chrysler Town and Country. After we got the new one on we realized that the female connector that connects to the solenoid has a prong stuck in it from the old EGR...


if you cannot pull it out with pliers or tweezers, then you will probaby have to replace the terminal in the female connector. Picking at it with a pick may help. but will most likely damage the connector. Whatever you do, be careful not to damage the connector shell. These can be very hard to come by. Pins with wire attached (pigtails) can be purchaced from the dealer. They usually do not have the entire connector shell available, but you can ask. With the pigtail, you would simply cut the wire and replace the connector pin in the connector. If they have the connector shell with wires, you would cut all the wires and splice a whole new connector shell onto the vehicle wiring harness.

Apr 02, 2011 | 2006 Chrysler Town & Country

1 Answer

How do I change a blower motor in a chrysler Town and country


Hello, to change the blower motor resistor follow this steps:
  1. Disconnect and isolate the battery negative cable.
  2. Open the glove box.
  3. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
  4. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle.Blower motor Resistor
  5. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  6. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  7. Remove the blower motor resistor from the evaporator housing.

Thanks

Aug 25, 2010 | 2006 Chrysler Town & Country

1 Answer

Looking to replace passenger side mirror on a 2006 Town and Country. Anyone have Instructions available?


    Remove Old Mirror
  1. 1 Open the side door to the Chrysler Town & Country, and find thescrew that holds the side mirror molding in place.

  2. Take the screw out and remove the molding panel that attached around the outside of the power mirror.

  3. Remove the bolts connecting the mirror to the door assembly. If equipped, unplug the power side view mirror wiring harness connector.

  4. Unplug the electric connectors, and pull the mirror out of the molding.

Jun 01, 2010 | 2006 Chrysler Town & Country

1 Answer

Who do i replace the rear ABS speed sensor on 2006


i belive theres two ,one on each wheel in the rear, you unplug connector, then remove the bolt holding sensor to backing plate and then remove, two wheel drive vans you need too replace the wheel bearing asm,heres two pictures too show you and then you see which type you have,one is the sensor the wire type the other is the bearing asm, hope this helps,6608e12.jpgdbfde76.jpga7cca55.jpg

May 15, 2010 | 2006 Chrysler Town & Country

1 Answer

2006 town and country overhead console temperature plug in


the ambient temp sensor is mounted in front of a/c condenser..sensor may be broken/missing..should be able to see sensor looking straight in front of lower grille opening..fairly inexpensive and not too bad to replace..dealer part

Apr 17, 2009 | 2006 Chrysler Town & Country

1 Answer

Map light replacement on 2006 Town and Country?


Jun 17, 2009- ok I just looked at it. it is simple.
the lens pivots and presses a switch in on one end to make the light come on. take a butter knife or very small screw driver and reach in between the lens and the black center console. there you will CAREFULLY press a flat tab to the side that is made onto the lens ( I hope you dont break this tab).
on the very opposite position on the clear lens towards the door is where the lens has a tab that has a small hole in it. there is a plastic pin made onto the console trim that fits into this hole so the lens will pivot. this will give you an idea of which direction to pull the lens when you press in the tab,. it does look like it would break easily. I havent had to take mine off yet thankfully.
please visit again and rank this answer if this helps!... good luck

Apr 13, 2009 | 2006 Chrysler Town & Country

Not finding what you are looking for?
2006 Chrysler Town & Country Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...